[PATCH RFC 5/8] dt-bindings: display: add Unisoc's mipi dsi&dphy bindings

[Maxime Ripard]

On Tue, Dec 10, 2019 at 04:36:32PM +0800, Kevin Tang wrote:
> From: Kevin Tang <kevin.tang at unisoc.com>
>
> Adds MIPI DSI Master and MIPI DSI-PHY (D-PHY)
> support for Unisoc's display subsystem.
>
> Cc: Orson Zhai <orsonzhai at gmail.com>
> Cc: Baolin Wang <baolin.wang at linaro.org>
> Cc: Chunyan Zhang <zhang.lyra at gmail.com>
> Signed-off-by: Kevin Tang <kevin.tang at unisoc.com>
> ---
>  .../devicetree/bindings/display/sprd/dphy.txt      | 49 ++++++++++++++++
>  .../devicetree/bindings/display/sprd/dsi.txt       | 68 ++++++++++++++++++++++
>  2 files changed, 117 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/sprd/dphy.txt
>  create mode 100644 Documentation/devicetree/bindings/display/sprd/dsi.txt
>
> diff --git a/Documentation/devicetree/bindings/display/sprd/dphy.txt b/Documentation/devicetree/bindings/display/sprd/dphy.txt
> new file mode 100644
> index 0000000..474c2b2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/sprd/dphy.txt
> @@ -0,0 +1,49 @@
> +Unisoc MIPI DSI-PHY (D-PHY)
> +============================================================================
> +
> +Required properties:
> +  - compatible: value should be "sprd,dsi-phy".
> +  - reg: must be the dsi controller base address.
> +  - #address-cells, #size-cells: should be set respectively to <1> and <0>
> +
> +Video interfaces:
> +  Device node can contain video interface port nodes according to [1].
> +  The following are properties specific to those nodes:
> +
> +  port node inbound:
> +    - reg: (required) must be 0.
> +  port node outbound:
> +    - reg: (required) must be 1.
> +
> +  endpoint node connected from DSI controller node (reg = 0):
> +    - remote-endpoint: specifies the endpoint in DSI node.
> +  endpoint node connected to panel node (reg = 1):
> +    - remote-endpoint: specifies the endpoint in panel node.
> +
> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> +
> +Example:
> +
> +	dphy: dphy {
> +		compatible = "sprd,dsi-phy";
> +		reg = <0x0 0x63100000 0x0 0x1000>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		/* input port*/
> +		port at 1 {
> +			reg = <1>;
> +			dphy_in: endpoint {
> +				remote-endpoint = <&dsi_out>;
> +			};
> +		};
> +
> +		/* output port */
> +		port at 0 {
> +			reg = <0>;
> +			dphy_out: endpoint {
> +				remote-endpoint = <&panel_in>;
> +			};
> +		};
> +	};

There's support for the MIPI D-PHY in the Linux PHY framework now, so
it would be a good fit for this (and that would mean using the generic
PHY bindings too.

> diff --git a/Documentation/devicetree/bindings/display/sprd/dsi.txt b/Documentation/devicetree/bindings/display/sprd/dsi.txt
> new file mode 100644
> index 0000000..1719ff5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/sprd/dsi.txt
> @@ -0,0 +1,68 @@
> +Unisoc MIPI DSI Master
> +=============================================================================
> +
> +Required properties:
> +  - compatible: value should be "sprd,dsi-host";
> +  - reg: physical base address and length of the registers set for the device
> +  - interrupts: should contain DSI interrupt
> +  - clocks: list of clock specifiers, must contain an entry for each required
> +	    entry in clock-names
> +  - clock-names: list of clock names sorted in the same order as the clocks
> +                 property.

Again, a list of the expected clock names and what they represent
would be great here.

Thanks!
Maxime
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 228 bytes
Desc: not available
URL: <https://lists.freedesktop.org/archives/dri-devel/attachments/20191213/f44896c7/attachment-0001.sig>