[PATCH v2 1/2] dt-bindings: display: bridge: Add documentation for SN65DSI84

Rob Herring robh at kernel.org
Thu Feb 4 17:40:37 UTC 2021


On Wed, Feb 03, 2021 at 12:42:55PM +0530, Jagan Teki wrote:
> SN65DSI84 is a Single Channel DSI to Dual-link LVDS bridge from
> Texas Instruments.
> 
> SN65DSI83, SN65DSI85 are variants of the same family of bridge
> controllers.
> 
> Right now the bridge driver is supporting a single link, dual-link
> support requires to initiate I2C Channel B registers, so dt-bindings
> documented with single link LVDS.
> 
> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
> ---
> Changes for v2:
> - none
> 
>  .../bindings/display/bridge/ti,sn65dsi84.yaml | 127 ++++++++++++++++++
>  1 file changed, 127 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi84.yaml
> 
> diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi84.yaml b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi84.yaml
> new file mode 100644
> index 000000000000..891382a76c1a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi84.yaml
> @@ -0,0 +1,127 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/bridge/ti,sn65dsi84.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: TI SN65DSI84 MIPI DSI to LVDS bridge bindings
> +
> +maintainers:
> +  - Jagan Teki <jagan at amarulasolutions.com>
> +
> +description: |
> +  The SN65DSI84 DSI to FlatLink bridge features a single channel MIPI D-PHY receiver
> +  front-end configuration with 4 lanes per channel operating at 1 Gbps per lanes.
> +  The bridge decodes MIPI DSI 18bpp RGB666 and 240bpp RG888 packets and converts
> +  the formatted video data stream to a FlatLink compatible LVDS output operating
> +  at pixel clocks operating from 25 MHx to 154 MHz, offering a Dual-Link LVDS,
> +  Single-Link LVDS interface with four data lanes per link.
> +
> +  https://www.ti.com/product/SN65DSI84
> +
> +properties:
> +  compatible:
> +    const: ti,sn65dsi84
> +
> +  reg:
> +    maxItems: 1
> +    description: i2c address of the bridge, 0x2c

Just 'const: 0x2c' if that's the only valid address.

> +
> +  enable-gpios:
> +    maxItems: 1
> +    description: GPIO specifier for bridge enable pin (active high).
> +
> +  ports:
> +    type: object
> +    description:
> +      A node containing input and output port nodes with endpoint definitions
> +      as documented in
> +      Documentation/devicetree/bindings/media/video-interfaces.txt
> +    properties:
> +      "#address-cells":
> +        const: 1
> +
> +      "#size-cells":
> +        const: 0
> +
> +      port at 0:
> +        type: object
> +        description: |
> +          DSI Input. The remote endpoint phandle should be a
> +          reference to a valid mipi_dsi_host device node.
> +
> +      port at 1:
> +        type: object
> +        description: |
> +          Video port for LVDS output (panel or connector).

This needs to use the graph.yaml schema. See the ones in drm-misc-next 
that are already converted.

> +
> +    required:
> +      - port at 0
> +      - port at 1
> +
> +required:
> +  - compatible
> +  - reg
> +  - enable-gpios
> +  - ports
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +
> +    dsi {
> +       #address-cells = <1>;
> +       #size-cells = <0>;
> +
> +       ports {
> +           #address-cells = <1>;
> +           #size-cells = <0>;
> +
> +           port at 0 {
> +               reg = <0>;
> +               dsi_in: endpoint {
> +                   remote-endpoint = <&ltdc_ep0_out>;
> +               };
> +           };
> +
> +           port at 1 {
> +               reg = <1>;
> +               dsi_out: endpoint {
> +                   remote-endpoint = <&bridge_in>;
> +                   data-lanes = <0 1>;
> +               };
> +           };
> +       };
> +    };
> +
> +    i2c6 {
> +       #address-cells = <1>;
> +       #size-cells = <0>;
> +
> +       bridge at 2c {
> +           compatible = "ti,sn65dsi84";
> +           reg = <0x2c>;
> +           enable-gpios = <&gpiof 15 GPIO_ACTIVE_HIGH>;
> +
> +           ports {
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               port at 0 {
> +                   reg = <0>;
> +                   bridge_in: endpoint {
> +                        remote-endpoint = <&dsi_out>;
> +                   };
> +               };
> +
> +               port at 1 {
> +                   reg = <1>;
> +                   bridge_out: endpoint {
> +                        remote-endpoint = <&panel_in_lvds>;
> +                   };
> +               };
> +           };
> +       };
> +    };
> -- 
> 2.25.1
> 


More information about the dri-devel mailing list