[PATCH] fbtft: add tearing signal detect

[Dan Carpenter]

On Sun, Jan 24, 2021 at 11:35:37PM +0800, Carlis wrote:
> +static irqreturn_t spi_panel_te_handler(int irq, void *data)
> +{
> +	complete(&spi_panel_te);
> +	return IRQ_HANDLED;
> +}
> +
> +static void enable_spi_panel_te_irq(struct fbtft_par *par, bool enable)

It quite confused me that enable actually disables.  I always feel like
it's clearer to write these as two separate functions.

> +{
> +	static int te_irq_count;
> +
> +	if (!par->gpio.te) {

This is always checked in the caller.  And it's when it's NULL that
means it's deliberate so don't print a message.

> +		pr_err("%s:%d,SPI panel TE GPIO not configured\n",
> +		       __func__, __LINE__);
> +		return;
> +	}
> +
> +	mutex_lock(&te_mutex);
> +
> +	if (enable) {
> +		if (++te_irq_count == 1)
> +			enable_irq(gpiod_to_irq(par->gpio.te));
> +	} else {
> +		if (--te_irq_count == 0)
> +			disable_irq(gpiod_to_irq(par->gpio.te));
> +	}
> +	mutex_unlock(&te_mutex);
> +}
> +
>  /**
>   * init_display() - initialize the display controller
>   *
> @@ -82,6 +117,28 @@ enum st7789v_command {
>   */
>  static int init_display(struct fbtft_par *par)
>  {
> +	int rc;
> +	struct device *dev = par->info->device;
> +
> +	par->gpio.te = devm_gpiod_get_index_optional(dev, "te", 0, GPIOD_IN);
> +	if (par->gpio.te) {

devm_gpiod_get_index_optional() can return NULL or error pointers.  If
it returns NULL then don't print an error message.  NULL reports are
deliberate.

	par->gpio.te = devm_gpiod_get_index_optional(dev, "te", 0, GPIOD_IN);
	if (IS_ERR(par->gpio.te)) {
		pr_err("%s:%d, TE gpio not specified\n", __func__, __LINE__);
		return PTR_ERR(par->gpio.te);
	}

	if (par->gpio.te) {


> +		init_completion(&spi_panel_te);
> +		mutex_init(&te_mutex);
> +		rc = devm_request_irq(dev,
> +				      gpiod_to_irq(par->gpio.te),
> +				     spi_panel_te_handler, IRQF_TRIGGER_RISING,
> +				     "TE_GPIO", par);
> +		if (rc) {
> +			pr_err("TE request_irq failed.\n");
> +			par->gpio.te = NULL;
> +		} else {
> +			disable_irq_nosync(gpiod_to_irq(par->gpio.te));
> +			pr_err("TE request_irq completion.\n");

Why is this printing an error message if devm_request_irq() succeeds?

> +		}
> +	} else {
> +		pr_err("%s:%d, TE gpio not specified\n",
> +		       __func__, __LINE__);
> +	}
>  	/* turn off sleep mode */
>  	write_reg(par, MIPI_DCS_EXIT_SLEEP_MODE);
>  	mdelay(120);
> @@ -137,6 +194,9 @@ static int init_display(struct fbtft_par *par)
>  	 */
>  	write_reg(par, PWCTRL1, 0xA4, 0xA1);
>  
> +    /*Tearing Effect Line On*/
> +	if (par->gpio.te)
> +		write_reg(par, 0x35, 0x00);
>  	write_reg(par, MIPI_DCS_SET_DISPLAY_ON);
>  
>  	if (HSD20_IPS)
> @@ -145,6 +205,76 @@ static int init_display(struct fbtft_par *par)
>  	return 0;
>  }
>  
> +/*****************************************************************************
> + *
> + *   int (*write_vmem)(struct fbtft_par *par);
> + *
> + *****************************************************************************/
> +
> +/* 16 bit pixel over 8-bit databus */
> +int st7789v_write_vmem16_bus8(struct fbtft_par *par, size_t offset, size_t len)
> +{
> +	u16 *vmem16;
> +	__be16 *txbuf16 = par->txbuf.buf;
> +	size_t remain;
> +	size_t to_copy;
> +	size_t tx_array_size;
> +	int i;
> +	int rc, ret = 0;

Delete one of these "rc" or "rec" variables.

> +	size_t startbyte_size = 0;
> +
> +	fbtft_par_dbg(DEBUG_WRITE_VMEM, par, "st7789v ---%s(offset=%zu, len=%zu)\n",
> +		      __func__, offset, len);
> +
> +	remain = len / 2;
> +	vmem16 = (u16 *)(par->info->screen_buffer + offset);
> +
> +	if (par->gpio.dc)
> +		gpiod_set_value(par->gpio.dc, 1);
> +
> +	/* non buffered write */
> +	if (!par->txbuf.buf)
> +		return par->fbtftops.write(par, vmem16, len);
> +
> +	/* buffered write */
> +	tx_array_size = par->txbuf.len / 2;
> +
> +	if (par->startbyte) {
> +		txbuf16 = par->txbuf.buf + 1;
> +		tx_array_size -= 2;
> +		*(u8 *)(par->txbuf.buf) = par->startbyte | 0x2;
> +		startbyte_size = 1;
> +	}
> +
> +	while (remain) {
> +		to_copy = min(tx_array_size, remain);
> +		dev_dbg(par->info->device, "    to_copy=%zu, remain=%zu\n",
> +			to_copy, remain - to_copy);
> +
> +		for (i = 0; i < to_copy; i++)
> +			txbuf16[i] = cpu_to_be16(vmem16[i]);
> +
> +		vmem16 = vmem16 + to_copy;
> +		if (par->gpio.te) {
> +			enable_spi_panel_te_irq(par, true);
> +			reinit_completion(&spi_panel_te);
> +			rc = wait_for_completion_timeout(&spi_panel_te,
> +							 msecs_to_jiffies(SPI_PANEL_TE_TIMEOUT));
> +			if (rc == 0)
> +				pr_err("wait panel TE time out\n");
> +		}
> +		ret = par->fbtftops.write(par, par->txbuf.buf,
> +								startbyte_size + to_copy * 2);

Line break is whacky.

> +		if (par->gpio.te)
> +			enable_spi_panel_te_irq(par, false);
> +		if (ret < 0)
> +			return ret;
> +		remain -= to_copy;
> +	}
> +
> +	return ret;

Shouldn't this be "return len;" or something?

> +}
> +

regards,
dan carpenter