[RESEND PATCH v1] dt-bindings: display/msm: convert MDP5 schema to YAML format
Dmitry Baryshkov
dmitry.baryshkov at linaro.org
Wed Nov 2 22:08:44 UTC 2022
Convert the mdp5.txt into the yaml format. Changes to the existing (txt) schema:
- MSM8996 has additional "iommu" clock, define it separately
- Add new properties used on some of platforms:
- interconnects, interconnect-names
- iommus
- power-domains
- operating-points-v2, opp-table
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
---
Resending as I noticed that I didn't include devicetree maintainers and
list in the first attempt.
---
.../devicetree/bindings/display/msm/mdp5.txt | 132 -----------------
.../bindings/display/msm/qcom,mdp5.yaml | 137 ++++++++++++++++++
2 files changed, 137 insertions(+), 132 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/msm/mdp5.txt
create mode 100644 Documentation/devicetree/bindings/display/msm/qcom,mdp5.yaml
diff --git a/Documentation/devicetree/bindings/display/msm/mdp5.txt b/Documentation/devicetree/bindings/display/msm/mdp5.txt
deleted file mode 100644
index 65d03c58dee6..000000000000
--- a/Documentation/devicetree/bindings/display/msm/mdp5.txt
+++ /dev/null
@@ -1,132 +0,0 @@
-Qualcomm adreno/snapdragon MDP5 display controller
-
-Description:
-
-This is the bindings documentation for the MDP5 display
-controller found in SoCs like MSM8974, APQ8084, MSM8916, MSM8994 and MSM8996.
-
-MDP5:
-Required properties:
-- compatible:
- * "qcom,mdp5" - MDP5
-- reg: Physical base address and length of the controller's registers.
-- reg-names: The names of register regions. The following regions are required:
- * "mdp_phys"
-- interrupts: Interrupt line from MDP5 to MDSS interrupt controller.
-- clocks: device clocks. See ../clocks/clock-bindings.txt for details.
-- clock-names: the following clocks are required.
-- * "bus"
-- * "iface"
-- * "core"
-- * "vsync"
-- ports: contains the list of output ports from MDP. These connect to interfaces
- that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a
- special case since it is a part of the MDP block itself).
-
- Each output port contains an endpoint that describes how it is connected to an
- external interface. These are described by the standard properties documented
- here:
- Documentation/devicetree/bindings/graph.txt
- Documentation/devicetree/bindings/media/video-interfaces.txt
-
- The availability of output ports can vary across SoC revisions:
-
- For MSM8974 and APQ8084:
- Port 0 -> MDP_INTF0 (eDP)
- Port 1 -> MDP_INTF1 (DSI1)
- Port 2 -> MDP_INTF2 (DSI2)
- Port 3 -> MDP_INTF3 (HDMI)
-
- For MSM8916:
- Port 0 -> MDP_INTF1 (DSI1)
-
- For MSM8994 and MSM8996:
- Port 0 -> MDP_INTF1 (DSI1)
- Port 1 -> MDP_INTF2 (DSI2)
- Port 2 -> MDP_INTF3 (HDMI)
-
-Optional properties:
-- clock-names: the following clocks are optional:
- * "lut"
- * "tbu"
- * "tbu_rt"
-
-Example:
-
-/ {
- ...
-
- mdss: mdss at 1a00000 {
- compatible = "qcom,mdss";
- reg = <0x1a00000 0x1000>,
- <0x1ac8000 0x3000>;
- reg-names = "mdss_phys", "vbif_phys";
-
- power-domains = <&gcc MDSS_GDSC>;
-
- clocks = <&gcc GCC_MDSS_AHB_CLK>,
- <&gcc GCC_MDSS_AXI_CLK>,
- <&gcc GCC_MDSS_VSYNC_CLK>;
- clock-names = "iface",
- "bus",
- "vsync"
-
- interrupts = <0 72 0>;
-
- interrupt-controller;
- #interrupt-cells = <1>;
-
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- mdp: mdp at 1a01000 {
- compatible = "qcom,mdp5";
- reg = <0x1a01000 0x90000>;
- reg-names = "mdp_phys";
-
- interrupt-parent = <&mdss>;
- interrupts = <0 0>;
-
- clocks = <&gcc GCC_MDSS_AHB_CLK>,
- <&gcc GCC_MDSS_AXI_CLK>,
- <&gcc GCC_MDSS_MDP_CLK>,
- <&gcc GCC_MDSS_VSYNC_CLK>;
- clock-names = "iface",
- "bus",
- "core",
- "vsync";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 0 {
- reg = <0>;
- mdp5_intf1_out: endpoint {
- remote-endpoint = <&dsi0_in>;
- };
- };
- };
- };
-
- dsi0: dsi at 1a98000 {
- ...
- ports {
- ...
- port at 0 {
- reg = <0>;
- dsi0_in: endpoint {
- remote-endpoint = <&mdp5_intf1_out>;
- };
- };
- ...
- };
- ...
- };
-
- dsi_phy0: dsi-phy at 1a98300 {
- ...
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/display/msm/qcom,mdp5.yaml b/Documentation/devicetree/bindings/display/msm/qcom,mdp5.yaml
new file mode 100644
index 000000000000..574e8b7bd67b
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/qcom,mdp5.yaml
@@ -0,0 +1,137 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/qcom,mdp5.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Adreno/Snapdragon Mobile Display controller (MDP5)
+
+description: >
+ MDP5 display controller found in SoCs like MSM8974, APQ8084, MSM8916, MSM8994
+ and MSM8996.
+
+maintainers:
+ - Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
+ - Rob Clark <robdclark at gmail.com>
+
+properties:
+ compatible:
+ const: qcom,mdp5
+
+ reg:
+ maxItems: 1
+
+ reg-names:
+ items:
+ - const: mdp_phys
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ minItems: 4
+ maxItems: 7
+
+ clock-names:
+ oneOf:
+ - minItems: 4
+ items:
+ - const: iface
+ - const: bus
+ - const: core
+ - const: vsync
+ - const: lut
+ - const: tbu
+ - const: tbu_rt
+ #MSM8996 has additional iommu clock
+ - items:
+ - const: iface
+ - const: bus
+ - const: core
+ - const: iommu
+ - const: vsync
+
+ interconnects:
+ minItems: 1
+ items:
+ - description: Interconnect path from mdp0 (or a single mdp) port to the data bus
+ - description: Interconnect path from mdp1 port to the data bus
+ - description: Interconnect path from rotator port to the data bus
+
+ interconnect-names:
+ minItems: 1
+ items:
+ - const: mdp0-mem
+ - const: mdp1-mem
+ - const: rotator-mem
+
+ iommus:
+ items:
+ - description: Phandle to apps_smmu node with SID mask for Hard-Fail port0
+
+ power-domains:
+ maxItems: 1
+
+ operating-points-v2: true
+ opp-table:
+ type: object
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+ description: |
+ Contains the list of output ports from DPU device. These ports
+ connect to interfaces that are external to the DPU hardware,
+ such as DSI, DP etc.
+
+ patternProperties:
+ "^port@[0-9a-f]+$":
+ $ref: /schemas/graph.yaml#/properties/port
+
+ # at least one port is required
+ required:
+ - port at 0
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - clock-names
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-msm8916.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ mdp at 1a01000 {
+ compatible = "qcom,mdp5";
+ reg = <0x1a01000 0x90000>;
+ reg-names = "mdp_phys";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_VSYNC_CLK>;
+ clock-names = "iface",
+ "bus",
+ "core",
+ "vsync";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+ };
+ };
+...
--
2.35.1
More information about the dri-devel
mailing list