[PATCH v1 4/5] arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge

[Krzysztof Kozlowski]

On 04/11/2022 09:13, Dmitry Baryshkov wrote:
> From: Vinod Koul <vkoul at kernel.org>
> 
> Add the LT9611uxc DSI-HDMI bridge and supplies
> 
> Signed-off-by: Vinod Koul <vkoul at kernel.org>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 61 +++++++++++++++++++++++++
>  1 file changed, 61 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> index e1a4cf1ee51d..9522dd29a38a 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> @@ -20,6 +20,28 @@ chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
>  
> +	lt9611_1v2: lt9611-vdd12-regulator {

Node name: drop lt9611

> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_1V2";
> +
> +		vin-supply = <&vph_pwr>;
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +		gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	lt9611_3v3: lt9611-3v3 {

Node name: drop lt9611 and add "regulator suffix

> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_3V3";
> +
> +		vin-supply = <&vreg_bob>;
> +		gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		enable-active-high;
> +	};
> +
>  	vph_pwr: vph-pwr-regulator {
>  		compatible = "regulator-fixed";
>  		regulator-name = "vph_pwr";
> @@ -349,6 +371,27 @@ vreg_l7e_2p8: ldo7 {
>  	};
>  };
>  
> +&i2c9 {
> +	status = "okay";
> +	clock-frequency = <400000>;
> +
> +	lt9611_codec: hdmi-bridge at 2b {
> +		compatible = "lontium,lt9611uxc";
> +		reg = <0x2b>;
> +
> +		interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
> +
> +		reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
> +
> +		vdd-supply = <&lt9611_1v2>;
> +		vcc-supply = <&lt9611_3v3>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
> +
> +	};
> +};
> +
>  &pcie0 {
>  	status = "okay";
>  	max-link-speed = <2>;
> @@ -394,8 +437,26 @@ &qupv3_id_0 {
>  	status = "okay";
>  };
>  
> +&qupv3_id_1 {
> +	status = "okay";
> +};
> +
>  &tlmm {
>  	gpio-reserved-ranges = <28 4>, <36 4>;
> +
> +	lt9611_irq_pin: lt9611-irq {

-state


Best regards,
Krzysztof