[PATCH v3 6/6] ARM: dts: stm32: Use new media bus type macros

[Laurent Pinchart]

Hugues, Maxime, Alexandre, could one of you take this patch in your tree
for v6.3 ? The two patches that it depends on have both been merged in
v6.2.

On Thu, Jun 16, 2022 at 01:14:10AM +0300, Laurent Pinchart wrote:
> Now that a header exists with macros for the media interface bus-type
> values, replace hardcoding numerical constants with the corresponding
> macros in the DT sources.
> 
> Signed-off-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
> ---
>  arch/arm/boot/dts/stm32429i-eval.dts  | 3 ++-
>  arch/arm/boot/dts/stm32mp157c-ev1.dts | 3 ++-
>  2 files changed, 4 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/stm32429i-eval.dts b/arch/arm/boot/dts/stm32429i-eval.dts
> index 0d98aca01736..5fae11e6607b 100644
> --- a/arch/arm/boot/dts/stm32429i-eval.dts
> +++ b/arch/arm/boot/dts/stm32429i-eval.dts
> @@ -50,6 +50,7 @@
>  #include "stm32f429-pinctrl.dtsi"
>  #include <dt-bindings/input/input.h>
>  #include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/media/video-interfaces.h>
>  
>  / {
>  	model = "STMicroelectronics STM32429i-EVAL board";
> @@ -186,7 +187,7 @@ &dcmi {
>  	port {
>  		dcmi_0: endpoint {
>  			remote-endpoint = <&ov2640_0>;
> -			bus-type = <5>;
> +			bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
>  			bus-width = <8>;
>  			hsync-active = <0>;
>  			vsync-active = <0>;
> diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
> index d142dd30e16b..306d41a6138f 100644
> --- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
> +++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
> @@ -8,6 +8,7 @@
>  #include "stm32mp157c-ed1.dts"
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/input.h>
> +#include <dt-bindings/media/video-interfaces.h>
>  
>  / {
>  	model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
> @@ -90,7 +91,7 @@ &dcmi {
>  	port {
>  		dcmi_0: endpoint {
>  			remote-endpoint = <&ov5640_0>;
> -			bus-type = <5>;
> +			bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
>  			bus-width = <8>;
>  			hsync-active = <0>;
>  			vsync-active = <0>;

-- 
Regards,

Laurent Pinchart