[PATCH v8 7/8] drm/msm/dpu: add DSC 1.2 hw blocks for relevant chipsets
Abhinav Kumar
quic_abhinavk at quicinc.com
Mon May 15 22:03:46 UTC 2023
On 5/15/2023 2:21 PM, Marijn Suijten wrote:
> On 2023-05-12 11:00:22, Kuogee Hsieh wrote:
>>
>> From: Abhinav Kumar <quic_abhinavk at quicinc.com>
>>
>> Add DSC 1.2 hardware blocks to the catalog with necessary sub-block and
>> feature flag information. Each display compression engine (DCE) contains
>> dual hard slice DSC encoders so both share same base address but with
>> its own different sub block address.
>
> Can we have an explanation of hard vs soft slices in some commit message
> and/or code documentation?
>
Not in this one. It wont look appropriate. I would rather remove "hard"
to avoid confusion.
>>
>> changes in v4:
>> -- delete DPU_DSC_HW_REV_1_1
>> -- re arrange sc8280xp_dsc[]
>>
>> changes in v4:
>> -- fix checkpatch warning
>>
>> Signed-off-by: Abhinav Kumar <quic_abhinavk at quicinc.com>
>> Signed-off-by: Kuogee Hsieh <quic_khsieh at quicinc.com>
>> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
>> ---
>> .../gpu/drm/msm/disp/dpu1/catalog/dpu_7_0_sm8350.h | 14 ++++++++++++
>> .../gpu/drm/msm/disp/dpu1/catalog/dpu_7_2_sc7280.h | 7 ++++++
>> .../drm/msm/disp/dpu1/catalog/dpu_8_0_sc8280xp.h | 16 ++++++++++++++
>> .../gpu/drm/msm/disp/dpu1/catalog/dpu_8_1_sm8450.h | 14 ++++++++++++
>> .../gpu/drm/msm/disp/dpu1/catalog/dpu_9_0_sm8550.h | 14 ++++++++++++
>> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c | 25 +++++++++++++++++++++-
>> 6 files changed, 89 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_0_sm8350.h b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_0_sm8350.h
>> index 500cfd0..c4c93c8 100644
>> --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_0_sm8350.h
>> +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_0_sm8350.h
>> @@ -153,6 +153,18 @@ static const struct dpu_merge_3d_cfg sm8350_merge_3d[] = {
>> MERGE_3D_BLK("merge_3d_2", MERGE_3D_2, 0x50000),
>> };
>>
>> +/*
>> + * NOTE: Each display compression engine (DCE) contains dual hard
>> + * slice DSC encoders so both share same base address but with
>> + * its own different sub block address.
>> + */
>> +static const struct dpu_dsc_cfg sm8350_dsc[] = {
>> + DSC_BLK_1_2("dce_0", DSC_0, 0x80000, 0x100, 0, dsc_sblk_0),
>
> Downstream says that the size is 0x10 (and 0x100 for the enc sblk, 0x10
> for the ctl sblk). This simply fills it up to the start of the enc sblk
> so that we can see all registers in the dump? After all only
> DSC_CMN_MAIN_CNF is defined in the main register space, so 0x10 is
> adequate.
>
.len today is always only for the dump. and yes even here we have only
0x100 for the enc and 0x10 for the ctl.
+static const struct dpu_dsc_sub_blks dsc_sblk_0 = {
+ .enc = {.base = 0x100, .len = 0x100},
+ .ctl = {.base = 0xF00, .len = 0x10},
+};
The issue here is that, the dpu snapshot does not handle sub_blk parsing
today. Its a to-do item. So for that reason, 0x100 was used here to
atleast get the full encoder dumps.
>> + DSC_BLK_1_2("dce_0", DSC_1, 0x80000, 0x100, 0, dsc_sblk_1),
>
> Should we add an extra suffix to the name to indicate which hard-slice
> DSC encoder it is? i.e. "dce_0_0" and "dce_0_1" etc?
Ok, that should be fine. We can add it.
>
>> + DSC_BLK_1_2("dce_1", DSC_2, 0x81000, 0x100, BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_0),
>> + DSC_BLK_1_2("dce_1", DSC_3, 0x81000, 0x100, BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_1),
>
> See comment below about loose BIT() in features.
Responded below.
>
>> +};
>> +
>> static const struct dpu_intf_cfg sm8350_intf[] = {
>> INTF_BLK("intf_0", INTF_0, 0x34000, 0x280, INTF_DP, MSM_DP_CONTROLLER_0, 24, INTF_SC7280_MASK,
>> DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR, 24),
>> @@ -215,6 +227,8 @@ const struct dpu_mdss_cfg dpu_sm8350_cfg = {
>> .dspp = sm8350_dspp,
>> .pingpong_count = ARRAY_SIZE(sm8350_pp),
>> .pingpong = sm8350_pp,
>> + .dsc = sm8350_dsc,
>> + .dsc_count = ARRAY_SIZE(sm8350_dsc),
>
> Count goes first **everywhere else**, let's not break consistency here.
>
the order of DSC entries is swapped for all chipsets. Please refer to
dpu_sc8180x_cfg, dpu_sm8250_cfg etc.
So if you are talking about consistency, this is actually consistent
with whats present in other chipsets.
If you are very particular about this, then once this lands, you can
change the order for all of them in another change.
Same answer for all swap comments.
>> .merge_3d_count = ARRAY_SIZE(sm8350_merge_3d),
>> .merge_3d = sm8350_merge_3d,
>> .intf_count = ARRAY_SIZE(sm8350_intf),
>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_2_sc7280.h b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_2_sc7280.h
>> index 5646713..42c66fe 100644
>> --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_2_sc7280.h
>> +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_2_sc7280.h
>> @@ -93,6 +93,11 @@ static const struct dpu_pingpong_cfg sc7280_pp[] = {
>> PP_BLK_DITHER("pingpong_3", PINGPONG_3, 0x6c000, 0, sc7280_pp_sblk, -1, -1),
>> };
>>
>> +/* NOTE: sc7280 only has one dsc hard slice encoder */
>
> DSC
>
>> +static const struct dpu_dsc_cfg sc7280_dsc[] = {
>> + DSC_BLK_1_2("dce_0", DSC_0, 0x80000, 0x100, BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_0),
>> +};
>> +
>> static const struct dpu_intf_cfg sc7280_intf[] = {
>> INTF_BLK("intf_0", INTF_0, 0x34000, 0x280, INTF_DP, MSM_DP_CONTROLLER_0, 24, INTF_SC7280_MASK,
>> DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR, 24),
>> @@ -149,6 +154,8 @@ const struct dpu_mdss_cfg dpu_sc7280_cfg = {
>> .mixer = sc7280_lm,
>> .pingpong_count = ARRAY_SIZE(sc7280_pp),
>> .pingpong = sc7280_pp,
>> + .dsc_count = ARRAY_SIZE(sc7280_dsc),
>> + .dsc = sc7280_dsc,
>> .intf_count = ARRAY_SIZE(sc7280_intf),
>> .intf = sc7280_intf,
>> .vbif_count = ARRAY_SIZE(sdm845_vbif),
>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_0_sc8280xp.h b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_0_sc8280xp.h
>> index 808aacd..1901fff 100644
>> --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_0_sc8280xp.h
>> +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_0_sc8280xp.h
>> @@ -141,6 +141,20 @@ static const struct dpu_merge_3d_cfg sc8280xp_merge_3d[] = {
>> MERGE_3D_BLK("merge_3d_2", MERGE_3D_2, 0x50000),
>> };
>>
>> +/*
>> + * NOTE: Each display compression engine (DCE) contains dual hard
>> + * slice DSC encoders so both share same base address but with
>> + * its own different sub block address.
>> + */
>> +static const struct dpu_dsc_cfg sc8280xp_dsc[] = {
>> + DSC_BLK_1_2("dce_0", DSC_0, 0x80000, 0x100, 0, dsc_sblk_0),
>> + DSC_BLK_1_2("dce_0", DSC_1, 0x80000, 0x100, 0, dsc_sblk_1),
>> + DSC_BLK_1_2("dce_1", DSC_2, 0x81000, 0x100, BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_0),
>> + DSC_BLK_1_2("dce_1", DSC_3, 0x81000, 0x100, BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_1),
>> + DSC_BLK_1_2("dce_2", DSC_4, 0x82000, 0x100, 0, dsc_sblk_0),
>> + DSC_BLK_1_2("dce_2", DSC_5, 0x82000, 0x100, 0, dsc_sblk_1),
>> +};
>> +
>> /* TODO: INTF 3, 8 and 7 are used for MST, marked as INTF_NONE for now */
>> static const struct dpu_intf_cfg sc8280xp_intf[] = {
>> INTF_BLK("intf_0", INTF_0, 0x34000, 0x280, INTF_DP, MSM_DP_CONTROLLER_0, 24, INTF_SC7280_MASK,
>> @@ -216,6 +230,8 @@ const struct dpu_mdss_cfg dpu_sc8280xp_cfg = {
>> .dspp = sc8280xp_dspp,
>> .pingpong_count = ARRAY_SIZE(sc8280xp_pp),
>> .pingpong = sc8280xp_pp,
>> + .dsc = sc8280xp_dsc,
>> + .dsc_count = ARRAY_SIZE(sc8280xp_dsc),
>
> Swap the two lines.
>
>> .merge_3d_count = ARRAY_SIZE(sc8280xp_merge_3d),
>> .merge_3d = sc8280xp_merge_3d,
>> .intf_count = ARRAY_SIZE(sc8280xp_intf),
>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_1_sm8450.h b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_1_sm8450.h
>> index 1a89ff9..741d03f 100644
>> --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_1_sm8450.h
>> +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_1_sm8450.h
>> @@ -161,6 +161,18 @@ static const struct dpu_merge_3d_cfg sm8450_merge_3d[] = {
>> MERGE_3D_BLK("merge_3d_3", MERGE_3D_3, 0x65f00),
>> };
>>
>> +/*
>> + * NOTE: Each display compression engine (DCE) contains dual hard
>> + * slice DSC encoders so both share same base address but with
>> + * its own different sub block address.
>> + */
>> +static const struct dpu_dsc_cfg sm8450_dsc[] = {
>> + DSC_BLK_1_2("dce_0", DSC_0, 0x80000, 0x100, 0, dsc_sblk_0),
>> + DSC_BLK_1_2("dce_0", DSC_1, 0x80000, 0x100, 0, dsc_sblk_1),
>> + DSC_BLK_1_2("dce_1", DSC_2, 0x81000, 0x100, BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_0),
>> + DSC_BLK_1_2("dce_1", DSC_3, 0x81000, 0x100, BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_1),
>> +};
>> +
>> static const struct dpu_intf_cfg sm8450_intf[] = {
>> INTF_BLK("intf_0", INTF_0, 0x34000, 0x280, INTF_DP, MSM_DP_CONTROLLER_0, 24, INTF_SC7280_MASK,
>> DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR, 24),
>> @@ -223,6 +235,8 @@ const struct dpu_mdss_cfg dpu_sm8450_cfg = {
>> .dspp = sm8450_dspp,
>> .pingpong_count = ARRAY_SIZE(sm8450_pp),
>> .pingpong = sm8450_pp,
>> + .dsc = sm8450_dsc,
>> + .dsc_count = ARRAY_SIZE(sm8450_dsc),
>
> Another swap.
>
>> .merge_3d_count = ARRAY_SIZE(sm8450_merge_3d),
>> .merge_3d = sm8450_merge_3d,
>> .intf_count = ARRAY_SIZE(sm8450_intf),
>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_9_0_sm8550.h b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_9_0_sm8550.h
>> index 497b34c..3ee6dc8 100644
>> --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_9_0_sm8550.h
>> +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_9_0_sm8550.h
>> @@ -165,6 +165,18 @@ static const struct dpu_merge_3d_cfg sm8550_merge_3d[] = {
>> MERGE_3D_BLK("merge_3d_3", MERGE_3D_3, 0x66700),
>> };
>>
>> +/*
>> + * NOTE: Each display compression engine (DCE) contains dual hard
>> + * slice DSC encoders so both share same base address but with
>> + * its own different sub block address.
>> + */
>> +static const struct dpu_dsc_cfg sm8550_dsc[] = {
>> + DSC_BLK_1_2("dce_0", DSC_0, 0x80000, 0x100, 0, dsc_sblk_0),
>> + DSC_BLK_1_2("dce_0", DSC_1, 0x80000, 0x100, 0, dsc_sblk_1),
>> + DSC_BLK_1_2("dce_1", DSC_2, 0x81000, 0x100, BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_0),
>> + DSC_BLK_1_2("dce_1", DSC_3, 0x81000, 0x100, BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_1),
>> +};
>> +
>> static const struct dpu_intf_cfg sm8550_intf[] = {
>> INTF_BLK("intf_0", INTF_0, 0x34000, 0x280, INTF_DP, MSM_DP_CONTROLLER_0, 24, INTF_SC7280_MASK,
>> DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR, 24),
>> @@ -227,6 +239,8 @@ const struct dpu_mdss_cfg dpu_sm8550_cfg = {
>> .dspp = sm8550_dspp,
>> .pingpong_count = ARRAY_SIZE(sm8550_pp),
>> .pingpong = sm8550_pp,
>> + .dsc = sm8550_dsc,
>> + .dsc_count = ARRAY_SIZE(sm8550_dsc),
>
> Swap.
>
>> .merge_3d_count = ARRAY_SIZE(sm8550_merge_3d),
>> .merge_3d = sm8550_merge_3d,
>> .intf_count = ARRAY_SIZE(sm8550_intf),
>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
>> index 78e4bf6..c1d7338 100644
>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
>> @@ -1,6 +1,6 @@
>> // SPDX-License-Identifier: GPL-2.0-only
>> /* Copyright (c) 2015-2018, The Linux Foundation. All rights reserved.
>> - * Copyright (c) 2022. Qualcomm Innovation Center, Inc. All rights reserved.
>> + * Copyright (c) 2022-2023, Qualcomm Innovation Center, Inc. All rights reserved.
>> */
>>
>> #define pr_fmt(fmt) "[drm:%s:%d] " fmt, __func__, __LINE__
>> @@ -522,6 +522,16 @@ static const struct dpu_pingpong_sub_blks sc7280_pp_sblk = {
>> /*************************************************************
>> * DSC sub blocks config
>> *************************************************************/
>> +static const struct dpu_dsc_sub_blks dsc_sblk_0 = {
>> + .enc = {.base = 0x100, .len = 0x100},
>> + .ctl = {.base = 0xF00, .len = 0x10},
>> +};
>> +
>> +static const struct dpu_dsc_sub_blks dsc_sblk_1 = {
>> + .enc = {.base = 0x200, .len = 0x100},
>> + .ctl = {.base = 0xF80, .len = 0x10},
>> +};
>> +
>> #define DSC_BLK(_name, _id, _base, _features) \
>> {\
>> .name = _name, .id = _id, \
>> @@ -529,6 +539,19 @@ static const struct dpu_pingpong_sub_blks sc7280_pp_sblk = {
>> .features = _features, \
>> }
>>
>> +/*
>> + * NOTE: Each display compression engine (DCE) contains dual hard
>> + * slice DSC encoders so both share same base address but with
>> + * its own different sub block address.
>> + */
>> +#define DSC_BLK_1_2(_name, _id, _base, _len, _features, _sblk) \
>
> There are no address values here so this comment doesn't seem very
> useful, and it is already duplicated on every DSC block array, where the
> duplication is more visible. Drop the comment here?
>
_base is the address. So base address. Does that clarify things?
>> + {\
>> + .name = _name, .id = _id, \
>> + .base = _base, .len = _len, \
>
> The len is always 0x100 (downstream says 0x10), should we hardcode it
> here and drop _len? We can always add it back if a future revision
> starts changing it, but that's not the case currently.
>
>> + .features = BIT(DPU_DSC_HW_REV_1_2) | _features, \
>
> We don't willy-nilly append bits like that: should there be global
> feature flags?
So this approach is actually better. This macro is a DSC_1_2 macro so it
will have the 1.2 feature flag and other features like native_422
support of that encoder are ORed on top of it. Nothing wrong with this.
>
> Or is this the start of a new era where we expand those defines in-line
> and drop them altogether? I'd much prefer that but we should first
> align on this direction (and then also make the switch globally in a
> followup).
>
Its case by case. No need to generalize.
In this the feature flag ORed with the base feature flag of DSC_1_2
makes it more clear.
> - Marijn
>
>> + .sblk = &_sblk, \
>> + }
>> +
>> /*************************************************************
>> * INTF sub blocks config
>> *************************************************************/
>> --
>> 2.7.4
>>
More information about the dri-devel
mailing list