[Freedreno] [PATCH v8 7/8] drm/msm/dpu: add DSC 1.2 hw blocks for relevant chipsets
Abhinav Kumar
quic_abhinavk at quicinc.com
Mon May 15 22:10:02 UTC 2023
On 5/15/2023 3:03 PM, Abhinav Kumar wrote:
>
>
> On 5/15/2023 2:21 PM, Marijn Suijten wrote:
>> On 2023-05-12 11:00:22, Kuogee Hsieh wrote:
>>>
>>> From: Abhinav Kumar <quic_abhinavk at quicinc.com>
>>>
>>> Add DSC 1.2 hardware blocks to the catalog with necessary sub-block and
>>> feature flag information. Each display compression engine (DCE)
>>> contains
>>> dual hard slice DSC encoders so both share same base address but with
>>> its own different sub block address.
>>
>> Can we have an explanation of hard vs soft slices in some commit message
>> and/or code documentation?
>>
>
> Not in this one. It wont look appropriate. I would rather remove "hard"
> to avoid confusion.
>
>>>
>>> changes in v4:
>>> -- delete DPU_DSC_HW_REV_1_1
>>> -- re arrange sc8280xp_dsc[]
>>>
>>> changes in v4:
>>> -- fix checkpatch warning
>>>
>>> Signed-off-by: Abhinav Kumar <quic_abhinavk at quicinc.com>
>>> Signed-off-by: Kuogee Hsieh <quic_khsieh at quicinc.com>
>>> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
>>> ---
>>> .../gpu/drm/msm/disp/dpu1/catalog/dpu_7_0_sm8350.h | 14 ++++++++++++
>>> .../gpu/drm/msm/disp/dpu1/catalog/dpu_7_2_sc7280.h | 7 ++++++
>>> .../drm/msm/disp/dpu1/catalog/dpu_8_0_sc8280xp.h | 16 ++++++++++++++
>>> .../gpu/drm/msm/disp/dpu1/catalog/dpu_8_1_sm8450.h | 14 ++++++++++++
>>> .../gpu/drm/msm/disp/dpu1/catalog/dpu_9_0_sm8550.h | 14 ++++++++++++
>>> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c | 25
>>> +++++++++++++++++++++-
>>> 6 files changed, 89 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_0_sm8350.h
>>> b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_0_sm8350.h
>>> index 500cfd0..c4c93c8 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_0_sm8350.h
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_0_sm8350.h
>>> @@ -153,6 +153,18 @@ static const struct dpu_merge_3d_cfg
>>> sm8350_merge_3d[] = {
>>> MERGE_3D_BLK("merge_3d_2", MERGE_3D_2, 0x50000),
>>> };
>>> +/*
>>> + * NOTE: Each display compression engine (DCE) contains dual hard
>>> + * slice DSC encoders so both share same base address but with
>>> + * its own different sub block address.
>>> + */
>>> +static const struct dpu_dsc_cfg sm8350_dsc[] = {
>>> + DSC_BLK_1_2("dce_0", DSC_0, 0x80000, 0x100, 0, dsc_sblk_0),
>>
>> Downstream says that the size is 0x10 (and 0x100 for the enc sblk, 0x10
>> for the ctl sblk). This simply fills it up to the start of the enc sblk
>> so that we can see all registers in the dump? After all only
>> DSC_CMN_MAIN_CNF is defined in the main register space, so 0x10 is
>> adequate.
>>
>
> .len today is always only for the dump. and yes even here we have only
> 0x100 for the enc and 0x10 for the ctl.
>
> +static const struct dpu_dsc_sub_blks dsc_sblk_0 = {
> + .enc = {.base = 0x100, .len = 0x100},
> + .ctl = {.base = 0xF00, .len = 0x10},
> +};
>
> The issue here is that, the dpu snapshot does not handle sub_blk parsing
> today. Its a to-do item. So for that reason, 0x100 was used here to
> atleast get the full encoder dumps.
>
>>> + DSC_BLK_1_2("dce_0", DSC_1, 0x80000, 0x100, 0, dsc_sblk_1),
>>
>> Should we add an extra suffix to the name to indicate which hard-slice
>> DSC encoder it is? i.e. "dce_0_0" and "dce_0_1" etc?
>
> Ok, that should be fine. We can add it.
>
>>
>>> + DSC_BLK_1_2("dce_1", DSC_2, 0x81000, 0x100,
>>> BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_0),
>>> + DSC_BLK_1_2("dce_1", DSC_3, 0x81000, 0x100,
>>> BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_1),
>>
>
>> See comment below about loose BIT() in features.
>
> Responded below.
>>
>>> +};
>>> +
>>> static const struct dpu_intf_cfg sm8350_intf[] = {
>>> INTF_BLK("intf_0", INTF_0, 0x34000, 0x280, INTF_DP,
>>> MSM_DP_CONTROLLER_0, 24, INTF_SC7280_MASK,
>>> DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR, 24),
>>> @@ -215,6 +227,8 @@ const struct dpu_mdss_cfg dpu_sm8350_cfg = {
>>> .dspp = sm8350_dspp,
>>> .pingpong_count = ARRAY_SIZE(sm8350_pp),
>>> .pingpong = sm8350_pp,
>>> + .dsc = sm8350_dsc,
>>> + .dsc_count = ARRAY_SIZE(sm8350_dsc),
>>
>> Count goes first **everywhere else**, let's not break consistency here.
>>
>
> the order of DSC entries is swapped for all chipsets. Please refer to
> dpu_sc8180x_cfg, dpu_sm8250_cfg etc.
>
> So if you are talking about consistency, this is actually consistent
> with whats present in other chipsets.
>
> If you are very particular about this, then once this lands, you can
> change the order for all of them in another change.
>
> Same answer for all swap comments.
Actually, I am wrong here, I misread the entries. Sure, I can fix this up.
Please ignore this response and you can check the others.
>
>>> .merge_3d_count = ARRAY_SIZE(sm8350_merge_3d),
>>> .merge_3d = sm8350_merge_3d,
>>> .intf_count = ARRAY_SIZE(sm8350_intf),
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_2_sc7280.h
>>> b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_2_sc7280.h
>>> index 5646713..42c66fe 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_2_sc7280.h
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_7_2_sc7280.h
>>> @@ -93,6 +93,11 @@ static const struct dpu_pingpong_cfg sc7280_pp[] = {
>>> PP_BLK_DITHER("pingpong_3", PINGPONG_3, 0x6c000, 0,
>>> sc7280_pp_sblk, -1, -1),
>>> };
>>> +/* NOTE: sc7280 only has one dsc hard slice encoder */
>>
>> DSC
>>
>>> +static const struct dpu_dsc_cfg sc7280_dsc[] = {
>>> + DSC_BLK_1_2("dce_0", DSC_0, 0x80000, 0x100,
>>> BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_0),
>>> +};
>>> +
>>> static const struct dpu_intf_cfg sc7280_intf[] = {
>>> INTF_BLK("intf_0", INTF_0, 0x34000, 0x280, INTF_DP,
>>> MSM_DP_CONTROLLER_0, 24, INTF_SC7280_MASK,
>>> DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR, 24),
>>> @@ -149,6 +154,8 @@ const struct dpu_mdss_cfg dpu_sc7280_cfg = {
>>> .mixer = sc7280_lm,
>>> .pingpong_count = ARRAY_SIZE(sc7280_pp),
>>> .pingpong = sc7280_pp,
>>> + .dsc_count = ARRAY_SIZE(sc7280_dsc),
>>> + .dsc = sc7280_dsc,
>>> .intf_count = ARRAY_SIZE(sc7280_intf),
>>> .intf = sc7280_intf,
>>> .vbif_count = ARRAY_SIZE(sdm845_vbif),
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_0_sc8280xp.h
>>> b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_0_sc8280xp.h
>>> index 808aacd..1901fff 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_0_sc8280xp.h
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_0_sc8280xp.h
>>> @@ -141,6 +141,20 @@ static const struct dpu_merge_3d_cfg
>>> sc8280xp_merge_3d[] = {
>>> MERGE_3D_BLK("merge_3d_2", MERGE_3D_2, 0x50000),
>>> };
>>> +/*
>>> + * NOTE: Each display compression engine (DCE) contains dual hard
>>> + * slice DSC encoders so both share same base address but with
>>> + * its own different sub block address.
>>> + */
>>> +static const struct dpu_dsc_cfg sc8280xp_dsc[] = {
>>> + DSC_BLK_1_2("dce_0", DSC_0, 0x80000, 0x100, 0, dsc_sblk_0),
>>> + DSC_BLK_1_2("dce_0", DSC_1, 0x80000, 0x100, 0, dsc_sblk_1),
>>> + DSC_BLK_1_2("dce_1", DSC_2, 0x81000, 0x100,
>>> BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_0),
>>> + DSC_BLK_1_2("dce_1", DSC_3, 0x81000, 0x100,
>>> BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_1),
>>> + DSC_BLK_1_2("dce_2", DSC_4, 0x82000, 0x100, 0, dsc_sblk_0),
>>> + DSC_BLK_1_2("dce_2", DSC_5, 0x82000, 0x100, 0, dsc_sblk_1),
>>> +};
>>> +
>>> /* TODO: INTF 3, 8 and 7 are used for MST, marked as INTF_NONE for
>>> now */
>>> static const struct dpu_intf_cfg sc8280xp_intf[] = {
>>> INTF_BLK("intf_0", INTF_0, 0x34000, 0x280, INTF_DP,
>>> MSM_DP_CONTROLLER_0, 24, INTF_SC7280_MASK,
>>> @@ -216,6 +230,8 @@ const struct dpu_mdss_cfg dpu_sc8280xp_cfg = {
>>> .dspp = sc8280xp_dspp,
>>> .pingpong_count = ARRAY_SIZE(sc8280xp_pp),
>>> .pingpong = sc8280xp_pp,
>>> + .dsc = sc8280xp_dsc,
>>> + .dsc_count = ARRAY_SIZE(sc8280xp_dsc),
>>
>> Swap the two lines.
>>
>>> .merge_3d_count = ARRAY_SIZE(sc8280xp_merge_3d),
>>> .merge_3d = sc8280xp_merge_3d,
>>> .intf_count = ARRAY_SIZE(sc8280xp_intf),
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_1_sm8450.h
>>> b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_1_sm8450.h
>>> index 1a89ff9..741d03f 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_1_sm8450.h
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_8_1_sm8450.h
>>> @@ -161,6 +161,18 @@ static const struct dpu_merge_3d_cfg
>>> sm8450_merge_3d[] = {
>>> MERGE_3D_BLK("merge_3d_3", MERGE_3D_3, 0x65f00),
>>> };
>>> +/*
>>> + * NOTE: Each display compression engine (DCE) contains dual hard
>>> + * slice DSC encoders so both share same base address but with
>>> + * its own different sub block address.
>>> + */
>>> +static const struct dpu_dsc_cfg sm8450_dsc[] = {
>>> + DSC_BLK_1_2("dce_0", DSC_0, 0x80000, 0x100, 0, dsc_sblk_0),
>>> + DSC_BLK_1_2("dce_0", DSC_1, 0x80000, 0x100, 0, dsc_sblk_1),
>>> + DSC_BLK_1_2("dce_1", DSC_2, 0x81000, 0x100,
>>> BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_0),
>>> + DSC_BLK_1_2("dce_1", DSC_3, 0x81000, 0x100,
>>> BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_1),
>>> +};
>>> +
>>> static const struct dpu_intf_cfg sm8450_intf[] = {
>>> INTF_BLK("intf_0", INTF_0, 0x34000, 0x280, INTF_DP,
>>> MSM_DP_CONTROLLER_0, 24, INTF_SC7280_MASK,
>>> DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR, 24),
>>> @@ -223,6 +235,8 @@ const struct dpu_mdss_cfg dpu_sm8450_cfg = {
>>> .dspp = sm8450_dspp,
>>> .pingpong_count = ARRAY_SIZE(sm8450_pp),
>>> .pingpong = sm8450_pp,
>>> + .dsc = sm8450_dsc,
>>> + .dsc_count = ARRAY_SIZE(sm8450_dsc),
>>
>> Another swap.
>>
>>> .merge_3d_count = ARRAY_SIZE(sm8450_merge_3d),
>>> .merge_3d = sm8450_merge_3d,
>>> .intf_count = ARRAY_SIZE(sm8450_intf),
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_9_0_sm8550.h
>>> b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_9_0_sm8550.h
>>> index 497b34c..3ee6dc8 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_9_0_sm8550.h
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_9_0_sm8550.h
>>> @@ -165,6 +165,18 @@ static const struct dpu_merge_3d_cfg
>>> sm8550_merge_3d[] = {
>>> MERGE_3D_BLK("merge_3d_3", MERGE_3D_3, 0x66700),
>>> };
>>> +/*
>>> + * NOTE: Each display compression engine (DCE) contains dual hard
>>> + * slice DSC encoders so both share same base address but with
>>> + * its own different sub block address.
>>> + */
>>> +static const struct dpu_dsc_cfg sm8550_dsc[] = {
>>> + DSC_BLK_1_2("dce_0", DSC_0, 0x80000, 0x100, 0, dsc_sblk_0),
>>> + DSC_BLK_1_2("dce_0", DSC_1, 0x80000, 0x100, 0, dsc_sblk_1),
>>> + DSC_BLK_1_2("dce_1", DSC_2, 0x81000, 0x100,
>>> BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_0),
>>> + DSC_BLK_1_2("dce_1", DSC_3, 0x81000, 0x100,
>>> BIT(DPU_DSC_NATIVE_422_EN), dsc_sblk_1),
>>> +};
>>> +
>>> static const struct dpu_intf_cfg sm8550_intf[] = {
>>> INTF_BLK("intf_0", INTF_0, 0x34000, 0x280, INTF_DP,
>>> MSM_DP_CONTROLLER_0, 24, INTF_SC7280_MASK,
>>> DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR, 24),
>>> @@ -227,6 +239,8 @@ const struct dpu_mdss_cfg dpu_sm8550_cfg = {
>>> .dspp = sm8550_dspp,
>>> .pingpong_count = ARRAY_SIZE(sm8550_pp),
>>> .pingpong = sm8550_pp,
>>> + .dsc = sm8550_dsc,
>>> + .dsc_count = ARRAY_SIZE(sm8550_dsc),
>>
>> Swap.
>>
>>> .merge_3d_count = ARRAY_SIZE(sm8550_merge_3d),
>>> .merge_3d = sm8550_merge_3d,
>>> .intf_count = ARRAY_SIZE(sm8550_intf),
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
>>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
>>> index 78e4bf6..c1d7338 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
>>> @@ -1,6 +1,6 @@
>>> // SPDX-License-Identifier: GPL-2.0-only
>>> /* Copyright (c) 2015-2018, The Linux Foundation. All rights reserved.
>>> - * Copyright (c) 2022. Qualcomm Innovation Center, Inc. All rights
>>> reserved.
>>> + * Copyright (c) 2022-2023, Qualcomm Innovation Center, Inc. All
>>> rights reserved.
>>> */
>>> #define pr_fmt(fmt) "[drm:%s:%d] " fmt, __func__, __LINE__
>>> @@ -522,6 +522,16 @@ static const struct dpu_pingpong_sub_blks
>>> sc7280_pp_sblk = {
>>> /*************************************************************
>>> * DSC sub blocks config
>>> *************************************************************/
>>> +static const struct dpu_dsc_sub_blks dsc_sblk_0 = {
>>> + .enc = {.base = 0x100, .len = 0x100},
>>> + .ctl = {.base = 0xF00, .len = 0x10},
>>> +};
>>> +
>>> +static const struct dpu_dsc_sub_blks dsc_sblk_1 = {
>>> + .enc = {.base = 0x200, .len = 0x100},
>>> + .ctl = {.base = 0xF80, .len = 0x10},
>>> +};
>>> +
>>> #define DSC_BLK(_name, _id, _base, _features) \
>>> {\
>>> .name = _name, .id = _id, \
>>> @@ -529,6 +539,19 @@ static const struct dpu_pingpong_sub_blks
>>> sc7280_pp_sblk = {
>>> .features = _features, \
>>> }
>>> +/*
>>> + * NOTE: Each display compression engine (DCE) contains dual hard
>>> + * slice DSC encoders so both share same base address but with
>>> + * its own different sub block address.
>>> + */
>>> +#define DSC_BLK_1_2(_name, _id, _base, _len, _features, _sblk) \
>>
>> There are no address values here so this comment doesn't seem very
>> useful, and it is already duplicated on every DSC block array, where the
>> duplication is more visible. Drop the comment here?
>>
>
> _base is the address. So base address. Does that clarify things?
>
>>> + {\
>>> + .name = _name, .id = _id, \
>>> + .base = _base, .len = _len, \
>>
>> The len is always 0x100 (downstream says 0x10), should we hardcode it
>> here and drop _len? We can always add it back if a future revision
>> starts changing it, but that's not the case currently.
>>
>>> + .features = BIT(DPU_DSC_HW_REV_1_2) | _features, \
>>
>> We don't willy-nilly append bits like that: should there be global
>> feature flags?
>
> So this approach is actually better. This macro is a DSC_1_2 macro so it
> will have the 1.2 feature flag and other features like native_422
> support of that encoder are ORed on top of it. Nothing wrong with this.
>
>>
>> Or is this the start of a new era where we expand those defines in-line
>> and drop them altogether? I'd much prefer that but we should first
>> align on this direction (and then also make the switch globally in a
>> followup).
>>
>
> Its case by case. No need to generalize.
>
> In this the feature flag ORed with the base feature flag of DSC_1_2
> makes it more clear.
>
>> - Marijn
>>
>>> + .sblk = &_sblk, \
>>> + }
>>> +
>>> /*************************************************************
>>> * INTF sub blocks config
>>> *************************************************************/
>>> --
>>> 2.7.4
>>>
More information about the dri-devel
mailing list