[PATCH v7 1/2] arm64: dts: qcom: sa8775p: add Display Serial Interface device nodes
Ayushi Makhija
quic_amakhija at quicinc.com
Mon May 19 11:00:55 UTC 2025
On 5/19/2025 6:31 AM, Dmitry Baryshkov wrote:
> On Tue, May 13, 2025 at 03:56:10PM +0530, Ayushi Makhija wrote:
>> From: Ayushi Makhija <quic_amakhija at quicinc.com>
>>
>> Add device tree nodes for the DSI0 and DSI1 controllers
>> with their corresponding PHYs found on Qualcomm SA8775P SoC.
>>
>> Signed-off-by: Ayushi Makhija <quic_amakhija at quicinc.com>
>> Reviewed-by: Dmitry Baryshkov <lumag at kernel.org>
>> Reviewed-by: Konrad Dybcio <konrad.dybcio at oss.qualcomm.com>
>> ---
>> arch/arm64/boot/dts/qcom/sa8775p.dtsi | 186 +++++++++++++++++++++++++-
>> 1 file changed, 185 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
>> index 5bd0c03476b1..f8777f17d24a 100644
>> --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
>> @@ -6,6 +6,7 @@
>>
>> #include <dt-bindings/interconnect/qcom,icc.h>
>> #include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/clock/qcom,dsi-phy-28nm.h>
>> #include <dt-bindings/clock/qcom,rpmh.h>
>> #include <dt-bindings/clock/qcom,sa8775p-dispcc.h>
>> #include <dt-bindings/clock/qcom,sa8775p-gcc.h>
>> @@ -4034,6 +4035,22 @@ dpu_intf4_out: endpoint {
>> remote-endpoint = <&mdss0_dp1_in>;
>> };
>> };
>> +
>> + port at 2 {
>> + reg = <2>;
>> +
>> + dpu_intf1_out: endpoint {
>> + remote-endpoint = <&mdss0_dsi0_in>;
>> + };
>> + };
>> +
>> + port at 3 {
>> + reg = <3>;
>> +
>> + dpu_intf2_out: endpoint {
>> + remote-endpoint = <&mdss0_dsi1_in>;
>> + };
>> + };
>> };
>>
>> mdss0_mdp_opp_table: opp-table {
>> @@ -4061,6 +4078,170 @@ opp-650000000 {
>> };
>> };
>>
>> + mdss0_dsi0: dsi at ae94000 {
>> + compatible = "qcom,sa8775p-dsi-ctrl", "qcom,mdss-dsi-ctrl";
>> + reg = <0x0 0x0ae94000 0x0 0x400>;
>> + reg-names = "dsi_ctrl";
>> +
>> + interrupt-parent = <&mdss0>;
>> + interrupts = <4>;
>> +
>> + clocks = <&dispcc0 MDSS_DISP_CC_MDSS_BYTE0_CLK>,
>> + <&dispcc0 MDSS_DISP_CC_MDSS_BYTE0_INTF_CLK>,
>> + <&dispcc0 MDSS_DISP_CC_MDSS_PCLK0_CLK>,
>> + <&dispcc0 MDSS_DISP_CC_MDSS_ESC0_CLK>,
>> + <&dispcc0 MDSS_DISP_CC_MDSS_AHB_CLK>,
>> + <&gcc GCC_DISP_HF_AXI_CLK>;
>> + clock-names = "byte",
>> + "byte_intf",
>> + "pixel",
>> + "core",
>> + "iface",
>> + "bus";
>> + assigned-clocks = <&dispcc0 MDSS_DISP_CC_MDSS_BYTE0_CLK_SRC>,
>> + <&dispcc0 MDSS_DISP_CC_MDSS_PCLK0_CLK_SRC>;
>> + assigned-clock-parents = <&mdss0_dsi0_phy DSI_BYTE_PLL_CLK>,
>> + <&mdss0_dsi0_phy DSI_PIXEL_PLL_CLK>;
>> + phys = <&mdss0_dsi0_phy>;
>> +
>> + operating-points-v2 = <&dsi0_opp_table>;
>> + power-domains = <&rpmhpd SA8775P_MMCX>;
>> +
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + status = "disabled";
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port at 0 {
>> + reg = <0>;
>> +
>> + mdss0_dsi0_in: endpoint {
>> + remote-endpoint = <&dpu_intf1_out>;
>> + };
>> + };
>> +
>> + port at 1 {
>> + reg = <1>;
>> +
>> + mdss0_dsi0_out: endpoint{ };
>> + };
>> + };
>> +
>> + dsi0_opp_table: opp-table {
>
> mdss_dsi_opp_table: opp-table {}
>
>> + compatible = "operating-points-v2";
>> +
>> + opp-358000000 {
>
> Is there only one entry? Usually there are several.
>
Hi Dmitry,
Thanks, for the review.
In the IP catalog Clock documentation of SA8775P, the same DSI clock frequency (358Mhz)
is mentioned for all the voltage corners (svs_l1, nom, turbo and turbo_l1).
That's why I kept the single entry opp-358000000 for 358Mhz and selected lowest voltage corner svs_l1.
I will address rest of the comments in next version of series.
Thanks,
Ayushi
>> + opp-hz = /bits/ 64 <358000000>;
>> + required-opps = <&rpmhpd_opp_svs_l1>;
>> + };
>> + };
>> + };
>> +
>> + mdss0_dsi0_phy: phy at ae94400 {
>> + compatible = "qcom,sa8775p-dsi-phy-5nm";
>> + reg = <0x0 0x0ae94400 0x0 0x200>,
>> + <0x0 0x0ae94600 0x0 0x280>,
>> + <0x0 0x0ae94900 0x0 0x27c>;
>> + reg-names = "dsi_phy",
>> + "dsi_phy_lane",
>> + "dsi_pll";
>> +
>> + #clock-cells = <1>;
>> + #phy-cells = <0>;
>> +
>> + clocks = <&dispcc0 MDSS_DISP_CC_MDSS_AHB_CLK>,
>> + <&rpmhcc RPMH_CXO_CLK>;
>> + clock-names = "iface", "ref";
>> +
>> + status = "disabled";
>> + };
>> +
>> + mdss0_dsi1: dsi at ae96000 {
>> + compatible = "qcom,sa8775p-dsi-ctrl", "qcom,mdss-dsi-ctrl";
>> + reg = <0x0 0x0ae96000 0x0 0x400>;
>> + reg-names = "dsi_ctrl";
>> +
>> + interrupt-parent = <&mdss0>;
>> + interrupts = <5>;
>> +
>> + clocks = <&dispcc0 MDSS_DISP_CC_MDSS_BYTE1_CLK>,
>> + <&dispcc0 MDSS_DISP_CC_MDSS_BYTE1_INTF_CLK>,
>> + <&dispcc0 MDSS_DISP_CC_MDSS_PCLK1_CLK>,
>> + <&dispcc0 MDSS_DISP_CC_MDSS_ESC1_CLK>,
>> + <&dispcc0 MDSS_DISP_CC_MDSS_AHB_CLK>,
>> + <&gcc GCC_DISP_HF_AXI_CLK>;
>> + clock-names = "byte",
>> + "byte_intf",
>> + "pixel",
>> + "core",
>> + "iface",
>> + "bus";
>> + assigned-clocks = <&dispcc0 MDSS_DISP_CC_MDSS_BYTE1_CLK_SRC>,
>> + <&dispcc0 MDSS_DISP_CC_MDSS_PCLK1_CLK_SRC>;
>> + assigned-clock-parents = <&mdss0_dsi1_phy DSI_BYTE_PLL_CLK>,
>> + <&mdss0_dsi1_phy DSI_PIXEL_PLL_CLK>;
>> + phys = <&mdss0_dsi1_phy>;
>> +
>> + operating-points-v2 = <&dsi1_opp_table>;
>> + power-domains = <&rpmhpd SA8775P_MMCX>;
>> +
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + status = "disabled";
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port at 0 {
>> + reg = <0>;
>> +
>> + mdss0_dsi1_in: endpoint {
>> + remote-endpoint = <&dpu_intf2_out>;
>> + };
>> + };
>> +
>> + port at 1 {
>> + reg = <1>;
>> +
>> + mdss0_dsi1_out: endpoint { };
>> + };
>> + };
>> +
>> + dsi1_opp_table: opp-table {
>
> You don't need a second DSI OPP table.
>
>> + compatible = "operating-points-v2";
>> +
>> + opp-358000000 {
>> + opp-hz = /bits/ 64 <358000000>;
>> + required-opps = <&rpmhpd_opp_svs_l1>;
>> + };
>> + };
>> + };
>> +
>> + mdss0_dsi1_phy: phy at ae96400 {
>> + compatible = "qcom,sa8775p-dsi-phy-5nm";
>> + reg = <0x0 0x0ae96400 0x0 0x200>,
>> + <0x0 0x0ae96600 0x0 0x280>,
>> + <0x0 0x0ae96900 0x0 0x27c>;
>> + reg-names = "dsi_phy",
>> + "dsi_phy_lane",
>> + "dsi_pll";
>> +
>> + #clock-cells = <1>;
>> + #phy-cells = <0>;
>> +
>> + clocks = <&dispcc0 MDSS_DISP_CC_MDSS_AHB_CLK>,
>> + <&rpmhcc RPMH_CXO_CLK>;
>> + clock-names = "iface", "ref";
>> +
>> + status = "disabled";
>> + };
>> +
>> mdss0_dp0_phy: phy at aec2a00 {
>> compatible = "qcom,sa8775p-edp-phy";
>>
>> @@ -4267,7 +4448,10 @@ dispcc0: clock-controller at af00000 {
>> <&sleep_clk>,
>> <&mdss0_dp0_phy 0>, <&mdss0_dp0_phy 1>,
>> <&mdss0_dp1_phy 0>, <&mdss0_dp1_phy 1>,
>> - <0>, <0>, <0>, <0>;
>> + <&mdss0_dsi0_phy DSI_BYTE_PLL_CLK>,
>> + <&mdss0_dsi0_phy DSI_PIXEL_PLL_CLK>,
>> + <&mdss0_dsi1_phy DSI_BYTE_PLL_CLK>,
>> + <&mdss0_dsi1_phy DSI_PIXEL_PLL_CLK>;
>> power-domains = <&rpmhpd SA8775P_MMCX>;
>> #clock-cells = <1>;
>> #reset-cells = <1>;
>> --
>> 2.34.1
>>
>
More information about the dri-devel
mailing list