[Freedreno] [PATCH v12 3/5] dt-bindings: drm/bridge: Document sn65dsi86 bridge bindings

[spanda at codeaurora.org]

On 2018-06-22 06:42, Stephen Boyd wrote:
> Quoting Sandeep Panda (2018-06-21 05:32:07)
>> diff --git 
>> a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt 
>> b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
>> new file mode 100644
>> index 000000000000..c8b8f018356f
>> --- /dev/null
>> +++ 
>> b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
>> @@ -0,0 +1,86 @@
>> +SN65DSI86 DSI to eDP bridge chip
>> +--------------------------------
>> +
>> +This is the binding for Texas Instruments SN65DSI86 bridge.
>> +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf
>> +
>> +Required properties:
>> +- compatible: Must be "ti,sn65dsi86"
>> +- reg: i2c address of the chip, 0x2d as per datasheet
>> +- enable-gpios: OF device-tree gpio specification for bridge_en pin 
>> (active high)
>> +
>> +- vccio-supply: A 1.8V supply that powers up the digital IOs.
>> +- vpll-supply: A 1.8V supply that powers up the displayport PLL.
>> +- vcca-supply: A 1.2V supply that powers up the analog circuits.
>> +- vcc-supply: A 1.2V supply that powers up the digital core.
>> +
>> +Optional properties:
>> +- interrupts-extended: Specifier for the SN65DSI86 interrupt line.
>> +
>> +- ddc-i2c-bus: phandle of the I2C controller used for DDC EDID 
>> probing
>> +
>> +- gpio-controller: Marks the device has a GPIO controller.
>> +- #gpio-cells    : Should be two. The first cell is the pin number 
>> and
>> +                   the second cell is used to specify flags.
>> +                   See ../../gpio/gpio.txt for more information.
>> +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description 
>> of
>> +               the cell formats.
>> +
>> +- clock-names: should be "refclk"
>> +- clocks: Specification for input reference clock. The reference
>> +         clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 
>> MHz.
>> +
>> +- data-lanes: See ../../media/video-interface.txt
>> +- lane-polarities: See ../../media/video-interface.txt
> 
> We need another property for suspend-gpios function of GPIO1. I suppose
> for the other GPIOs we don't need anything like this because they're
> output functions only? GPIO4 can do PWM and I guess if pwm is used in 
> DT
> from here then the driver can mux that out of gpio4 properly. I have no
> idea how the hsync and vsync GPIOs would work though. I see that GPIO3
> can do DSIA hsync or vsync and GPIO2 can do DSIA vsync and I would 
> guess
> those are in output mode only. Maybe that's just another property on
> this node to indicate if we should mux out the function or not. Usually
> that's done from pinctrl though. I don't have a use case for those
> functions but I do care about suspend gpios so at least add that one
> please.

I was thinking of adding gpio1 (suspend-gpio) documentation when we add
support for PSR feature. Since for PSR we will be using this 
suspoend-gpio.