[PATCH v4 6/7] arm64: qcom: dts: sm8550: add interconnect and opp-peak-kBps for GPU

[Akhil P Oommen]

On 12/9/2024 6:32 PM, Akhil P Oommen wrote:
> On 12/5/2024 8:31 PM, Neil Armstrong wrote:
>> Each GPU OPP requires a specific peak DDR bandwidth, let's add
>> those to each OPP and also the related interconnect path.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong at linaro.org>
> 
> I haven't checked each bw value, still
> 
> Reviewed-by: Akhil P Oommen <quic_akhilpo at quicinc.com>
> 
> -Akhil
> 
>> ---
>>  arch/arm64/boot/dts/qcom/sm8550.dtsi | 13 +++++++++++++
>>  1 file changed, 13 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
>> index e7774d32fb6d2288748ecec00bf525b2b3c40fbb..955f58b2cb4e4ca3fd33f1555e36a15cfc82d642 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
>> @@ -14,6 +14,7 @@
>>  #include <dt-bindings/firmware/qcom,scm.h>
>>  #include <dt-bindings/gpio/gpio.h>
>>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/interconnect/qcom,icc.h>
>>  #include <dt-bindings/interconnect/qcom,sm8550-rpmh.h>
>>  #include <dt-bindings/mailbox/qcom-ipcc.h>
>>  #include <dt-bindings/power/qcom-rpmpd.h>
>> @@ -2114,6 +2115,10 @@ gpu: gpu at 3d00000 {
>>  			qcom,gmu = <&gmu>;
>>  			#cooling-cells = <2>;
>>  
>> +			interconnects = <&gem_noc MASTER_GFX3D QCOM_ICC_TAG_ALWAYS
>> +					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
>> +			interconnect-names = "gfx-mem";
>> +
>>  			status = "disabled";
>>  
>>  			zap-shader {
>> @@ -2127,41 +2132,49 @@ gpu_opp_table: opp-table {
>>  				opp-680000000 {
>>  					opp-hz = /bits/ 64 <680000000>;
>>  					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
>> +					opp-peak-kBps = <16500000>;
>>  				};
>>  
>>  				opp-615000000 {
>>  					opp-hz = /bits/ 64 <615000000>;
>>  					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L0>;
>> +					opp-peak-kBps = <16500000>;

Seems like you are using value from "qcom,bus-max" node for each opp in
downstream devicetree. Except for the highest OPP, we should use the
value from "qcom,bus-freq" node. That is supposed to give the best perf
per watt.

-Akhil.

>>  				};
>>  
>>  				opp-550000000 {
>>  					opp-hz = /bits/ 64 <550000000>;
>>  					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
>> +					opp-peak-kBps = <12449218>;
>>  				};
>>  
>>  				opp-475000000 {
>>  					opp-hz = /bits/ 64 <475000000>;
>>  					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_L1>;
>> +					opp-peak-kBps = <8171875>;
>>  				};
>>  
>>  				opp-401000000 {
>>  					opp-hz = /bits/ 64 <401000000>;
>>  					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
>> +					opp-peak-kBps = <6671875>;
>>  				};
>>  
>>  				opp-348000000 {
>>  					opp-hz = /bits/ 64 <348000000>;
>>  					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D0>;
>> +					opp-peak-kBps = <6074218>;
>>  				};
>>  
>>  				opp-295000000 {
>>  					opp-hz = /bits/ 64 <295000000>;
>>  					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>;
>> +					opp-peak-kBps = <6074218>;
>>  				};
>>  
>>  				opp-220000000 {
>>  					opp-hz = /bits/ 64 <220000000>;
>>  					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D2>;
>> +					opp-peak-kBps = <6074218>;
>>  				};
>>  			};
>>  		};
>>
>