[PATCH v4 9/9] arm64: dts: qcom: Add display support for QCS615 RIDE board

[Dmitry Baryshkov]

On Tue, Dec 10, 2024 at 02:54:00PM +0800, Fange Zhang wrote:
> From: Li Liu <quic_lliu6 at quicinc.com>
> 
> Add display MDSS and DSI configuration for QCS615 RIDE board.
> QCS615 has a DP port, and DP support will be added in a later patch.
> 
> Signed-off-by: Li Liu <quic_lliu6 at quicinc.com>
> Signed-off-by: Fange Zhang <quic_fangez at quicinc.com>
> ---
>  arch/arm64/boot/dts/qcom/qcs615-ride.dts | 89 ++++++++++++++++++++++++++++++++
>  1 file changed, 89 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qcs615-ride.dts b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
> index a25928933e2b66241258e418c6e5bc36c306101e..694719a09ac46bfa2fe34f1883c0970b9d0902be 100644
> --- a/arch/arm64/boot/dts/qcom/qcs615-ride.dts
> +++ b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
> @@ -32,6 +32,18 @@ xo_board_clk: xo-board-clk {
>  			#clock-cells = <0>;
>  		};
>  	};
> +
> +	dp-connector {
> +		compatible = "dp-connector";
> +		label = "DP";
> +		type = "mini";
> +
> +		port {
> +			dp_connector_out: endpoint {
> +				remote-endpoint = <&anx_7625_out>;
> +			};
> +		};
> +	};
>  };
>  
>  &apps_rsc {
> @@ -202,6 +214,83 @@ &gcc {
>  		 <&sleep_clk>;
>  };
>  
> +&i2c2 {
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	ioexp: gpio at 3e {
> +		compatible = "semtech,sx1509q";
> +		reg = <0x3e>;
> +		interrupt-parent = <&tlmm>;
> +		interrupts = <58 0>;

Use IRQ flags instead of just 0 (here and further on). Also it might be
better to use interrupts-extended instead.

> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		semtech,probe-reset;
> +	};
> +
> +	i2c-mux at 77 {
> +		compatible = "nxp,pca9542";
> +		reg = <0x77>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;

Add empty line before device nodes (here and furher on).

> +		i2c at 0 {
> +			reg = <0>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			anx7625 at 58 {
> +				compatible = "analogix,anx7625";
> +				reg = <0x58>;
> +				interrupt-parent = <&ioexp>;
> +				interrupts = <0 0>;
> +				enable-gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
> +				reset-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
> +				wakeup-source;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port at 0 {
> +						reg = <0>;
> +						anx_7625_in: endpoint {
> +							remote-endpoint = <&mdss_dsi0_out>;
> +						};
> +					};
> +
> +					port at 1 {
> +						reg = <1>;
> +						anx_7625_out: endpoint {
> +							remote-endpoint = <&dp_connector_out>;
> +						};
> +					};
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&mdss {
> +	status = "okay";
> +};
> +
> +&mdss_dsi0 {
> +	vdda-supply = <&vreg_l11a>;
> +	status = "okay";
> +};
> +
> +&mdss_dsi0_out {
> +	remote-endpoint = <&anx_7625_in>;
> +	data-lanes = <0 1 2 3>;
> +};
> +
> +&mdss_dsi0_phy {
> +	vdds-supply = <&vreg_l5a>;
> +	status = "okay";
> +};
> +
>  &qupv3_id_0 {
>  	status = "okay";
>  };
> 
> -- 
> 2.34.1
> 

-- 
With best wishes
Dmitry