[PATCH v4 9/9] arm64: dts: qcom: Add display support for QCS615 RIDE board

[fange zhang]

On 2024/12/13 18:19, Dmitry Baryshkov wrote:
> On Fri, 13 Dec 2024 at 11:21, fange zhang <quic_fangez at quicinc.com> wrote:
>>
>>
>>
>> On 2024/12/10 19:02, Dmitry Baryshkov wrote:
>>> On Tue, Dec 10, 2024 at 02:54:00PM +0800, Fange Zhang wrote:
>>>> From: Li Liu <quic_lliu6 at quicinc.com>
>>>>
>>>> Add display MDSS and DSI configuration for QCS615 RIDE board.
>>>> QCS615 has a DP port, and DP support will be added in a later patch.
>>>>
>>>> Signed-off-by: Li Liu <quic_lliu6 at quicinc.com>
>>>> Signed-off-by: Fange Zhang <quic_fangez at quicinc.com>
>>>> ---
>>>>    arch/arm64/boot/dts/qcom/qcs615-ride.dts | 89 ++++++++++++++++++++++++++++++++
>>>>    1 file changed, 89 insertions(+)
>>>>
>>>> diff --git a/arch/arm64/boot/dts/qcom/qcs615-ride.dts b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
>>>> index a25928933e2b66241258e418c6e5bc36c306101e..694719a09ac46bfa2fe34f1883c0970b9d0902be 100644
>>>> --- a/arch/arm64/boot/dts/qcom/qcs615-ride.dts
>>>> +++ b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
>>>> @@ -32,6 +32,18 @@ xo_board_clk: xo-board-clk {
>>>>                       #clock-cells = <0>;
>>>>               };
>>>>       };
>>>> +
>>>> +    dp-connector {
>>>> +            compatible = "dp-connector";
>>>> +            label = "DP";
>>>> +            type = "mini";
>>>> +
>>>> +            port {
>>>> +                    dp_connector_out: endpoint {
>>>> +                            remote-endpoint = <&anx_7625_out>;
>>>> +                    };
>>>> +            };
>>>> +    };
>>>>    };
>>>>
>>>>    &apps_rsc {
>>>> @@ -202,6 +214,83 @@ &gcc {
>>>>                <&sleep_clk>;
>>>>    };
>>>>
>>>> +&i2c2 {
>>>> +    clock-frequency = <400000>;
>>>> +    status = "okay";
>>>> +
>>>> +    ioexp: gpio at 3e {
>>>> +            compatible = "semtech,sx1509q";
>>>> +            reg = <0x3e>;
>>>> +            interrupt-parent = <&tlmm>;
>>>> +            interrupts = <58 0>;
>>>
>>> Use IRQ flags instead of just 0 (here and further on). Also it might be
>>> better to use interrupts-extended instead.
>> Got it, will use interrupts-extended instead
>> -               interrupt-parent = <&tlmm>;
>> -               interrupts = <58 0>;
>> +               interrupts-extended = <&tlmm 58 IRQ_TYPE_NONE>;
>>>
>>>> +            gpio-controller;
>>>> +            #gpio-cells = <2>;
>>>> +            interrupt-controller;
>>>> +            #interrupt-cells = <2>;
>>>> +            semtech,probe-reset;
>>>> +    };
>>>> +
>>>> +    i2c-mux at 77 {
>>>> +            compatible = "nxp,pca9542";
>>>> +            reg = <0x77>;
>>>> +            #address-cells = <1>;
>>>> +            #size-cells = <0>;
>>>
>>> Add empty line before device nodes (here and furher on).
>> Sorry, will add it in next patch.
>>>
>>>> +            i2c at 0 {
>>>> +                    reg = <0>;
>>>> +                    #address-cells = <1>;
>>>> +                    #size-cells = <0>;
>>>> +
>>>> +                    anx7625 at 58 {
>>>> +                            compatible = "analogix,anx7625";
>>>> +                            reg = <0x58>;
>>>> +                            interrupt-parent = <&ioexp>;
>>>> +                            interrupts = <0 0>;
>> will change it to interrupts-extended in next patch
>> -               interrupt-parent = <&ioexp>;
>> -               interrupts = <0 0>;
>> +               interrupts-extended = <&ioexp 0 IRQ_TYPE_NONE>;
> 
> Yes, much better. BTW: are you sure that it's really IRQ_TYPE_NONE?
We extensively tested FALLING and BOTH type, and they all work. However, 
I believe it’s better to use the default type, which is the same as the 
downstream approach. This way, it will be more stable.
> 
>>>> +                            enable-gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
>>>> +                            reset-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
>>>> +                            wakeup-source;
>>>> +
>>>> +                            ports {
>>>> +                                    #address-cells = <1>;
>>>> +                                    #size-cells = <0>;
>>>> +
>>>> +                                    port at 0 {
>>>> +                                            reg = <0>;
>>>> +                                            anx_7625_in: endpoint {
>>>> +                                                    remote-endpoint = <&mdss_dsi0_out>;
>>>> +                                            };
>>>> +                                    };
>>>> +
>>>> +                                    port at 1 {
>>>> +                                            reg = <1>;
>>>> +                                            anx_7625_out: endpoint {
>>>> +                                                    remote-endpoint = <&dp_connector_out>;
>>>> +                                            };
>>>> +                                    };
>>>> +                            };
>>>> +                    };
>>>> +            };
>>>> +    };
>>>> +};
>>>> +
>>>> +&mdss {
>>>> +    status = "okay";
>>>> +};
>>>> +
>>>> +&mdss_dsi0 {
>>>> +    vdda-supply = <&vreg_l11a>;
>>>> +    status = "okay";
>>>> +};
>>>> +
>>>> +&mdss_dsi0_out {
>>>> +    remote-endpoint = <&anx_7625_in>;
>>>> +    data-lanes = <0 1 2 3>;
>>>> +};
>>>> +
>>>> +&mdss_dsi0_phy {
>>>> +    vdds-supply = <&vreg_l5a>;
>>>> +    status = "okay";
>>>> +};
>>>> +
>>>>    &qupv3_id_0 {
>>>>       status = "okay";
>>>>    };
>>>>
>>>> --
>>>> 2.34.1
>>>>
>>>
>>
> 
>