[Intel-gfx] [PATCH] drm/i915: enable sdvo interrupt on pch platforms

[Jesse Barnes]

On Mon, 10 Dec 2012 01:37:18 +0100
Daniel Vetter <daniel.vetter at ffwll.ch> wrote:

> Noticed while strolling through docs. Might make a few dual-link dvi
> users happy(ier).
> 
> v2: Remove the unrelated debug hacks in intel_display.c
> 
> v3: Preserve register contexts to not upset fastboot or the modeset
> hw state checker.
> 
> v4: Actually enable it in the irq handler/postinstall functions, too
> 
> Signed-off-by: Daniel Vetter <daniel.vetter at ffwll.ch>
> ---
>  drivers/gpu/drm/i915/i915_irq.c   |  3 +++
>  drivers/gpu/drm/i915/i915_reg.h   |  6 ++++--
>  drivers/gpu/drm/i915/intel_sdvo.c | 14 +++++++++++++-
>  3 files changed, 20 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
> index d02e022..e9b9460 100644
> --- a/drivers/gpu/drm/i915/i915_irq.c
> +++ b/drivers/gpu/drm/i915/i915_irq.c
> @@ -1910,6 +1910,7 @@ static int ironlake_irq_postinstall(struct drm_device *dev)
>  				SDE_PORTB_HOTPLUG_CPT |
>  				SDE_PORTC_HOTPLUG_CPT |
>  				SDE_PORTD_HOTPLUG_CPT |
> +				SDE_SDVOB_HOTPLUG_CPT |
>  				SDE_GMBUS_CPT |
>  				SDE_AUX_MASK_CPT);
>  	} else {
> @@ -1917,6 +1918,7 @@ static int ironlake_irq_postinstall(struct drm_device *dev)
>  				SDE_PORTB_HOTPLUG |
>  				SDE_PORTC_HOTPLUG |
>  				SDE_PORTD_HOTPLUG |
> +				SDE_SDVOB_HOTPLUG |
>  				SDE_GMBUS |
>  				SDE_AUX_MASK);
>  	}
> @@ -1979,6 +1981,7 @@ static int ivybridge_irq_postinstall(struct drm_device *dev)
>  			SDE_PORTB_HOTPLUG_CPT |
>  			SDE_PORTC_HOTPLUG_CPT |
>  			SDE_PORTD_HOTPLUG_CPT |
> +			SDE_SDVOB_HOTPLUG_CPT |
>  			SDE_GMBUS_CPT |
>  			SDE_AUX_MASK_CPT);
>  	dev_priv->pch_irq_mask = ~hotplug_mask;

I guess this needs fixing on top of your latest hotplug setup changes.

> diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> index f2a5ea6..d8162f8 100644
> --- a/drivers/gpu/drm/i915/i915_reg.h
> +++ b/drivers/gpu/drm/i915/i915_reg.h
> @@ -1673,7 +1673,7 @@
>  #define   SDVO_ENABLE		(1 << 31)
>  #define   SDVO_PIPE_B_SELECT	(1 << 30)
>  #define   SDVO_STALL_SELECT	(1 << 29)
> -#define   SDVO_INTERRUPT_ENABLE	(1 << 26)
> +#define   SDVO_INTERRUPT_ENABLE_PCH	(1 << 23)

Why drop the old one?  Not possible to use there too?

> @@ -1085,6 +1085,9 @@ static void intel_sdvo_mode_set(struct drm_encoder *encoder,
>  	if (!mode)
>  		return;
>  
> +	/* Preserve the PCH interrupt enable bit. */
> +	sdvox = I915_READ(intel_sdvo->sdvo_reg) & SDVO_INTERRUPT_ENABLE_PCH;
> +

Don't we unconditionally set sdvox later?  Do you need to add some
s/=/|=/ later on in sdvo_mode_set?

>  	/* First, set the input mapping for the first input to our controlled
>  	 * output. This is only correct if we're a single-input device, in
>  	 * which case the first input is the output from the appropriate SDVO
> @@ -2775,9 +2778,18 @@ bool intel_sdvo_init(struct drm_device *dev, uint32_t sdvo_reg, bool is_sdvob)
>  	/* Only enable the hotplug irq if we need it, to work around noisy
>  	 * hotplug lines.
>  	 */
> -	if (intel_sdvo->hotplug_active)
> +	if (intel_sdvo->hotplug_active) {
>  		dev_priv->hotplug_supported_mask |= hotplug_mask;
>  
> +		if (HAS_PCH_SPLIT(dev)) {
> +			u32 temp;
> +
> +			temp = I915_READ(intel_sdvo->sdvo_reg);
> +			temp &= SDVO_INTERRUPT_ENABLE_PCH;
> +			intel_sdvo_write_sdvox(intel_sdvo, temp);
> +		}
> +	}

Clearing everything but the interrupt enable bit?  Or should this be |=?

-- 
Jesse Barnes, Intel Open Source Technology Center