[Intel-gfx] [PATCH 07/25] drm/i915: split out DPLL update code from i9xx_crtc_mode_set
Jesse Barnes
jbarnes at virtuousgeek.org
Wed Mar 21 20:48:28 CET 2012
ValleyView needs something different here, and it cleans up the function
quite a bit.
Signed-off-by: Jesse Barnes <jbarnes at virtuousgeek.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy at linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes at virtuousgeek.org>
---
drivers/gpu/drm/i915/intel_display.c | 408 +++++++++++++++++++--------------
1 files changed, 235 insertions(+), 173 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 084e154..f9ac7b7 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -5245,6 +5245,233 @@ static void i9xx_update_pll_dividers(struct drm_crtc *crtc,
}
}
+static void intel_update_lvds(struct drm_crtc *crtc, intel_clock_t *clock,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int pipe = intel_crtc->pipe;
+ u32 temp, lvds_sync = 0;
+
+ temp = I915_READ(LVDS);
+ temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
+ if (pipe == 1) {
+ temp |= LVDS_PIPEB_SELECT;
+ } else {
+ temp &= ~LVDS_PIPEB_SELECT;
+ }
+ /* set the corresponsding LVDS_BORDER bit */
+ temp |= dev_priv->lvds_border_bits;
+ /* Set the B0-B3 data pairs corresponding to whether we're going to
+ * set the DPLLs for dual-channel mode or not.
+ */
+ if (clock->p2 == 7)
+ temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
+ else
+ temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
+
+ /* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
+ * appropriately here, but we need to look more thoroughly into how
+ * panels behave in the two modes.
+ */
+ /* set the dithering flag on LVDS as needed */
+ if (INTEL_INFO(dev)->gen >= 4) {
+ if (dev_priv->lvds_dither)
+ temp |= LVDS_ENABLE_DITHER;
+ else
+ temp &= ~LVDS_ENABLE_DITHER;
+ }
+ if (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC)
+ lvds_sync |= LVDS_HSYNC_POLARITY;
+ if (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC)
+ lvds_sync |= LVDS_VSYNC_POLARITY;
+ if ((temp & (LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY))
+ != lvds_sync) {
+ char flags[2] = "-+";
+ DRM_INFO("Changing LVDS panel from "
+ "(%chsync, %cvsync) to (%chsync, %cvsync)\n",
+ flags[!(temp & LVDS_HSYNC_POLARITY)],
+ flags[!(temp & LVDS_VSYNC_POLARITY)],
+ flags[!(lvds_sync & LVDS_HSYNC_POLARITY)],
+ flags[!(lvds_sync & LVDS_VSYNC_POLARITY)]);
+ temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
+ temp |= lvds_sync;
+ }
+ I915_WRITE(LVDS, temp);
+}
+
+static void i9xx_update_pll(struct drm_crtc *crtc,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode,
+ intel_clock_t *clock, intel_clock_t *reduced_clock,
+ int num_connectors)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int pipe = intel_crtc->pipe;
+ u32 dpll;
+ bool is_sdvo;
+
+ is_sdvo = intel_pipe_has_type(crtc, INTEL_OUTPUT_SDVO) ||
+ intel_pipe_has_type(crtc, INTEL_OUTPUT_HDMI);
+
+ dpll = DPLL_VGA_MODE_DIS;
+
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
+ dpll |= DPLLB_MODE_LVDS;
+ else
+ dpll |= DPLLB_MODE_DAC_SERIAL;
+ if (is_sdvo) {
+ int pixel_multiplier = intel_mode_get_pixel_multiplier(adjusted_mode);
+ if (pixel_multiplier > 1) {
+ if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
+ dpll |= (pixel_multiplier - 1) << SDVO_MULTIPLIER_SHIFT_HIRES;
+ }
+ dpll |= DPLL_DVO_HIGH_SPEED;
+ }
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT))
+ dpll |= DPLL_DVO_HIGH_SPEED;
+
+ /* compute bitmask from p1 value */
+ if (IS_PINEVIEW(dev))
+ dpll |= (1 << (clock->p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT_PINEVIEW;
+ else {
+ dpll |= (1 << (clock->p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
+ if (IS_G4X(dev) && reduced_clock)
+ dpll |= (1 << (reduced_clock->p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
+ }
+ switch (clock->p2) {
+ case 5:
+ dpll |= DPLL_DAC_SERIAL_P2_CLOCK_DIV_5;
+ break;
+ case 7:
+ dpll |= DPLLB_LVDS_P2_CLOCK_DIV_7;
+ break;
+ case 10:
+ dpll |= DPLL_DAC_SERIAL_P2_CLOCK_DIV_10;
+ break;
+ case 14:
+ dpll |= DPLLB_LVDS_P2_CLOCK_DIV_14;
+ break;
+ }
+ if (INTEL_INFO(dev)->gen >= 4)
+ dpll |= (6 << PLL_LOAD_PULSE_PHASE_SHIFT);
+
+ if (is_sdvo && intel_pipe_has_type(crtc, INTEL_OUTPUT_TVOUT))
+ dpll |= PLL_REF_INPUT_TVCLKINBC;
+ else if (intel_pipe_has_type(crtc, INTEL_OUTPUT_TVOUT))
+ /* XXX: just matching BIOS for now */
+ /* dpll |= PLL_REF_INPUT_TVCLKINBC; */
+ dpll |= 3;
+ else if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS) &&
+ intel_panel_use_ssc(dev_priv) && num_connectors < 2)
+ dpll |= PLLB_REF_INPUT_SPREADSPECTRUMIN;
+ else
+ dpll |= PLL_REF_INPUT_DREFCLK;
+
+ dpll |= DPLL_VCO_ENABLE;
+ I915_WRITE(DPLL(pipe), dpll & ~DPLL_VCO_ENABLE);
+ POSTING_READ(DPLL(pipe));
+ udelay(150);
+
+ /* The LVDS pin pair needs to be on before the DPLLs are enabled.
+ * This is an exception to the general rule that mode_set doesn't turn
+ * things on.
+ */
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
+ intel_update_lvds(crtc, clock, adjusted_mode);
+
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT))
+ intel_dp_set_m_n(crtc, mode, adjusted_mode);
+
+ I915_WRITE(DPLL(pipe), dpll);
+
+ /* Wait for the clocks to stabilize. */
+ POSTING_READ(DPLL(pipe));
+ udelay(150);
+
+ if (INTEL_INFO(dev)->gen >= 4) {
+ u32 temp = 0;
+ if (is_sdvo) {
+ temp = intel_mode_get_pixel_multiplier(adjusted_mode);
+ if (temp > 1)
+ temp = (temp - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT;
+ else
+ temp = 0;
+ }
+ I915_WRITE(DPLL_MD(pipe), temp);
+ } else {
+ /* The pixel multiplier can only be updated once the
+ * DPLL is enabled and the clocks are stable.
+ *
+ * So write it again.
+ */
+ I915_WRITE(DPLL(pipe), dpll);
+ }
+}
+
+static void i8xx_update_pll(struct drm_crtc *crtc,
+ struct drm_display_mode *adjusted_mode,
+ intel_clock_t *clock,
+ int num_connectors)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int pipe = intel_crtc->pipe;
+ u32 dpll;
+
+ dpll = DPLL_VGA_MODE_DIS;
+
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)) {
+ dpll |= (1 << (clock->p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
+ } else {
+ if (clock->p1 == 2)
+ dpll |= PLL_P1_DIVIDE_BY_TWO;
+ else
+ dpll |= (clock->p1 - 2) << DPLL_FPA01_P1_POST_DIV_SHIFT;
+ if (clock->p2 == 4)
+ dpll |= PLL_P2_DIVIDE_BY_4;
+ }
+
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_TVOUT))
+ /* XXX: just matching BIOS for now */
+ /* dpll |= PLL_REF_INPUT_TVCLKINBC; */
+ dpll |= 3;
+ else if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS) &&
+ intel_panel_use_ssc(dev_priv) && num_connectors < 2)
+ dpll |= PLLB_REF_INPUT_SPREADSPECTRUMIN;
+ else
+ dpll |= PLL_REF_INPUT_DREFCLK;
+
+ dpll |= DPLL_VCO_ENABLE;
+ I915_WRITE(DPLL(pipe), dpll & ~DPLL_VCO_ENABLE);
+ POSTING_READ(DPLL(pipe));
+ udelay(150);
+
+ /* The LVDS pin pair needs to be on before the DPLLs are enabled.
+ * This is an exception to the general rule that mode_set doesn't turn
+ * things on.
+ */
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
+ intel_update_lvds(crtc, clock, adjusted_mode);
+
+ I915_WRITE(DPLL(pipe), dpll);
+
+ /* Wait for the clocks to stabilize. */
+ POSTING_READ(DPLL(pipe));
+ udelay(150);
+
+ /* The pixel multiplier can only be updated once the
+ * DPLL is enabled and the clocks are stable.
+ *
+ * So write it again.
+ */
+ I915_WRITE(DPLL(pipe), dpll);
+}
+
static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
struct drm_display_mode *mode,
struct drm_display_mode *adjusted_mode,
@@ -5258,15 +5485,13 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
int plane = intel_crtc->plane;
int refclk, num_connectors = 0;
intel_clock_t clock, reduced_clock;
- u32 dpll, dspcntr, pipeconf, vsyncshift;
- bool ok, has_reduced_clock = false, is_sdvo = false, is_dvo = false;
- bool is_crt = false, is_lvds = false, is_tv = false, is_dp = false;
+ u32 dspcntr, pipeconf, vsyncshift;
+ bool ok, has_reduced_clock = false, is_sdvo = false;
+ bool is_lvds = false, is_tv = false;
struct drm_mode_config *mode_config = &dev->mode_config;
struct intel_encoder *encoder;
const intel_limit_t *limit;
int ret;
- u32 temp;
- u32 lvds_sync = 0;
list_for_each_entry(encoder, &mode_config->encoder_list, base.head) {
if (encoder->base.crtc != crtc)
@@ -5282,18 +5507,9 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
if (encoder->needs_tv_clock)
is_tv = true;
break;
- case INTEL_OUTPUT_DVO:
- is_dvo = true;
- break;
case INTEL_OUTPUT_TVOUT:
is_tv = true;
break;
- case INTEL_OUTPUT_ANALOG:
- is_crt = true;
- break;
- case INTEL_OUTPUT_DISPLAYPORT:
- is_dp = true;
- break;
}
num_connectors++;
@@ -5337,71 +5553,12 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
i9xx_update_pll_dividers(crtc, &clock, has_reduced_clock ?
&reduced_clock : NULL);
- dpll = DPLL_VGA_MODE_DIS;
-
- if (!IS_GEN2(dev)) {
- if (is_lvds)
- dpll |= DPLLB_MODE_LVDS;
- else
- dpll |= DPLLB_MODE_DAC_SERIAL;
- if (is_sdvo) {
- int pixel_multiplier = intel_mode_get_pixel_multiplier(adjusted_mode);
- if (pixel_multiplier > 1) {
- if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
- dpll |= (pixel_multiplier - 1) << SDVO_MULTIPLIER_SHIFT_HIRES;
- }
- dpll |= DPLL_DVO_HIGH_SPEED;
- }
- if (is_dp)
- dpll |= DPLL_DVO_HIGH_SPEED;
-
- /* compute bitmask from p1 value */
- if (IS_PINEVIEW(dev))
- dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT_PINEVIEW;
- else {
- dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
- if (IS_G4X(dev) && has_reduced_clock)
- dpll |= (1 << (reduced_clock.p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
- }
- switch (clock.p2) {
- case 5:
- dpll |= DPLL_DAC_SERIAL_P2_CLOCK_DIV_5;
- break;
- case 7:
- dpll |= DPLLB_LVDS_P2_CLOCK_DIV_7;
- break;
- case 10:
- dpll |= DPLL_DAC_SERIAL_P2_CLOCK_DIV_10;
- break;
- case 14:
- dpll |= DPLLB_LVDS_P2_CLOCK_DIV_14;
- break;
- }
- if (INTEL_INFO(dev)->gen >= 4)
- dpll |= (6 << PLL_LOAD_PULSE_PHASE_SHIFT);
- } else {
- if (is_lvds) {
- dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
- } else {
- if (clock.p1 == 2)
- dpll |= PLL_P1_DIVIDE_BY_TWO;
- else
- dpll |= (clock.p1 - 2) << DPLL_FPA01_P1_POST_DIV_SHIFT;
- if (clock.p2 == 4)
- dpll |= PLL_P2_DIVIDE_BY_4;
- }
- }
-
- if (is_sdvo && is_tv)
- dpll |= PLL_REF_INPUT_TVCLKINBC;
- else if (is_tv)
- /* XXX: just matching BIOS for now */
- /* dpll |= PLL_REF_INPUT_TVCLKINBC; */
- dpll |= 3;
- else if (is_lvds && intel_panel_use_ssc(dev_priv) && num_connectors < 2)
- dpll |= PLLB_REF_INPUT_SPREADSPECTRUMIN;
+ if (IS_GEN2(dev))
+ i8xx_update_pll(crtc, adjusted_mode, &clock, num_connectors);
else
- dpll |= PLL_REF_INPUT_DREFCLK;
+ i9xx_update_pll(crtc, mode, adjusted_mode, &clock,
+ has_reduced_clock ? &reduced_clock : NULL,
+ num_connectors);
/* setup pipeconf */
pipeconf = I915_READ(PIPECONF(pipe));
@@ -5430,105 +5587,10 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
/* default to 8bpc */
pipeconf &= ~(PIPECONF_BPP_MASK | PIPECONF_DITHER_EN);
- if (is_dp) {
- if (mode->private_flags & INTEL_MODE_DP_FORCE_6BPC) {
- pipeconf |= PIPECONF_BPP_6 |
- PIPECONF_DITHER_EN |
- PIPECONF_DITHER_TYPE_SP;
- }
- }
-
- dpll |= DPLL_VCO_ENABLE;
DRM_DEBUG_KMS("Mode for pipe %c:\n", pipe == 0 ? 'A' : 'B');
drm_mode_debug_printmodeline(mode);
- I915_WRITE(DPLL(pipe), dpll & ~DPLL_VCO_ENABLE);
-
- POSTING_READ(DPLL(pipe));
- udelay(150);
-
- /* The LVDS pin pair needs to be on before the DPLLs are enabled.
- * This is an exception to the general rule that mode_set doesn't turn
- * things on.
- */
- if (is_lvds) {
- temp = I915_READ(LVDS);
- temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
- if (pipe == 1) {
- temp |= LVDS_PIPEB_SELECT;
- } else {
- temp &= ~LVDS_PIPEB_SELECT;
- }
- /* set the corresponsding LVDS_BORDER bit */
- temp |= dev_priv->lvds_border_bits;
- /* Set the B0-B3 data pairs corresponding to whether we're going to
- * set the DPLLs for dual-channel mode or not.
- */
- if (clock.p2 == 7)
- temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
- else
- temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
-
- /* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
- * appropriately here, but we need to look more thoroughly into how
- * panels behave in the two modes.
- */
- /* set the dithering flag on LVDS as needed */
- if (INTEL_INFO(dev)->gen >= 4) {
- if (dev_priv->lvds_dither)
- temp |= LVDS_ENABLE_DITHER;
- else
- temp &= ~LVDS_ENABLE_DITHER;
- }
- if (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC)
- lvds_sync |= LVDS_HSYNC_POLARITY;
- if (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC)
- lvds_sync |= LVDS_VSYNC_POLARITY;
- if ((temp & (LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY))
- != lvds_sync) {
- char flags[2] = "-+";
- DRM_INFO("Changing LVDS panel from "
- "(%chsync, %cvsync) to (%chsync, %cvsync)\n",
- flags[!(temp & LVDS_HSYNC_POLARITY)],
- flags[!(temp & LVDS_VSYNC_POLARITY)],
- flags[!(lvds_sync & LVDS_HSYNC_POLARITY)],
- flags[!(lvds_sync & LVDS_VSYNC_POLARITY)]);
- temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
- temp |= lvds_sync;
- }
- I915_WRITE(LVDS, temp);
- }
-
- if (is_dp) {
- intel_dp_set_m_n(crtc, mode, adjusted_mode);
- }
-
- I915_WRITE(DPLL(pipe), dpll);
-
- /* Wait for the clocks to stabilize. */
- POSTING_READ(DPLL(pipe));
- udelay(150);
-
- if (INTEL_INFO(dev)->gen >= 4) {
- temp = 0;
- if (is_sdvo) {
- temp = intel_mode_get_pixel_multiplier(adjusted_mode);
- if (temp > 1)
- temp = (temp - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT;
- else
- temp = 0;
- }
- I915_WRITE(DPLL_MD(pipe), temp);
- } else {
- /* The pixel multiplier can only be updated once the
- * DPLL is enabled and the clocks are stable.
- *
- * So write it again.
- */
- I915_WRITE(DPLL(pipe), dpll);
- }
-
if (HAS_PIPE_CXSR(dev)) {
if (intel_crtc->lowfreq_avail) {
DRM_DEBUG_KMS("enabling CxSR downclocking\n");
--
1.7.5.4
More information about the Intel-gfx
mailing list