[Intel-gfx] [PATCH 11/13] drm/i915: do full backlight setup at enable time
Jani Nikula
jani.nikula at intel.com
Fri Nov 8 15:49:03 CET 2013
We should now have all the information we need to do a full
initialization of the backlight registers.
Signed-off-by: Jani Nikula <jani.nikula at intel.com>
---
drivers/gpu/drm/i915/intel_panel.c | 145 ++++++++++++++++++++++--------------
1 file changed, 89 insertions(+), 56 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_panel.c b/drivers/gpu/drm/i915/intel_panel.c
index 0e8f0a3..da088e3 100644
--- a/drivers/gpu/drm/i915/intel_panel.c
+++ b/drivers/gpu/drm/i915/intel_panel.c
@@ -719,50 +719,71 @@ static void pch_enable_backlight(struct intel_connector *connector)
enum pipe pipe = intel_get_pipe_from_connector(connector);
enum transcoder cpu_transcoder =
intel_pipe_to_cpu_transcoder(dev_priv, pipe);
- u32 tmp;
-
- tmp = I915_READ(BLC_PWM_CPU_CTL2);
+ u32 cpu_ctl2, pch_ctl1, pch_ctl2;
- /* Note that this can also get called through dpms changes. And
- * we don't track the backlight dpms state, hence check whether
- * we have to do anything first. */
- if (tmp & BLM_PWM_ENABLE)
- return;
+ cpu_ctl2 = I915_READ(BLC_PWM_CPU_CTL2);
+ if (cpu_ctl2 & BLM_PWM_ENABLE) {
+ WARN(1, "cpu backlight already enabled\n");
+ cpu_ctl2 &= ~BLM_PWM_ENABLE;
+ I915_WRITE(BLC_PWM_CPU_CTL2, cpu_ctl2);
+ }
- if (INTEL_INFO(dev)->num_pipes == 3)
- tmp &= ~BLM_PIPE_SELECT_IVB;
- else
- tmp &= ~BLM_PIPE_SELECT;
+ pch_ctl1 = I915_READ(BLC_PWM_PCH_CTL1);
+ if (pch_ctl1 & BLM_PCH_PWM_ENABLE) {
+ DRM_DEBUG_KMS("pch backlight already enabled\n");
+ pch_ctl1 &= ~BLM_PCH_PWM_ENABLE;
+ I915_WRITE(BLC_PWM_PCH_CTL1, pch_ctl1);
+ }
if (cpu_transcoder == TRANSCODER_EDP)
- tmp |= BLM_TRANSCODER_EDP;
+ cpu_ctl2 = BLM_TRANSCODER_EDP;
else
- tmp |= BLM_PIPE(cpu_transcoder);
- tmp &= ~BLM_PWM_ENABLE;
-
- I915_WRITE(BLC_PWM_CPU_CTL2, tmp);
+ cpu_ctl2 = BLM_PIPE(cpu_transcoder);
+ I915_WRITE(BLC_PWM_CPU_CTL2, cpu_ctl2);
POSTING_READ(BLC_PWM_CPU_CTL2);
- I915_WRITE(BLC_PWM_CPU_CTL2, tmp | BLM_PWM_ENABLE);
-
- if (!(dev_priv->quirks & QUIRK_NO_PCH_PWM_ENABLE)) {
- tmp = I915_READ(BLC_PWM_PCH_CTL1);
- tmp |= BLM_PCH_PWM_ENABLE;
- tmp &= ~BLM_PCH_OVERRIDE_ENABLE;
- I915_WRITE(BLC_PWM_PCH_CTL1, tmp);
- }
+ I915_WRITE(BLC_PWM_CPU_CTL2, cpu_ctl2 | BLM_PWM_ENABLE);
- /*
- * Call below after setting BLC_PWM_CPU_CTL2 and BLC_PWM_PCH_CTL1.
- * BLC_PWM_CPU_CTL may be cleared to zero automatically when these
- * registers are set.
- */
+ /* This won't stick until the above enable. */
intel_panel_actually_set_backlight(connector, panel->backlight.level);
+
+ pch_ctl2 = panel->backlight.max << 16;
+ I915_WRITE(BLC_PWM_PCH_CTL2, pch_ctl2);
+
+ pch_ctl1 = 0;
+ if (panel->backlight.active_low_pwm)
+ pch_ctl1 |= BLM_PCH_POLARITY;
+ I915_WRITE(BLC_PWM_PCH_CTL1, pch_ctl1);
+ POSTING_READ(BLC_PWM_PCH_CTL1);
+ I915_WRITE(BLC_PWM_PCH_CTL1, pch_ctl1 | BLM_PCH_PWM_ENABLE);
}
static void i9xx_enable_backlight(struct intel_connector *connector)
{
+ struct drm_device *dev = connector->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_panel *panel = &connector->panel;
+ u32 ctl, freq;
+ ctl = I915_READ(BLC_PWM_CTL);
+ if (ctl & BACKLIGHT_DUTY_CYCLE_MASK_PNV) {
+ WARN(1, "backlight already enabled\n");
+ I915_WRITE(BLC_PWM_CTL, 0);
+ }
+
+ freq = panel->backlight.max;
+ if (panel->backlight.combination_mode)
+ freq /= 0xff;
+
+ ctl = freq << 17;
+ if (IS_GEN2(dev) && panel->backlight.combination_mode)
+ ctl |= BLM_LEGACY_MODE;
+ if (IS_PINEVIEW(dev) && panel->backlight.active_low_pwm)
+ ctl |= BLM_POLARITY_PNV;
+
+ I915_WRITE(BLC_PWM_CTL, ctl);
+ POSTING_READ(BLC_PWM_CTL);
+
+ /* XXX: combine this into above write? */
intel_panel_actually_set_backlight(connector, panel->backlight.level);
}
@@ -772,25 +793,33 @@ static void i965_enable_backlight(struct intel_connector *connector)
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_panel *panel = &connector->panel;
enum pipe pipe = intel_get_pipe_from_connector(connector);
- u32 tmp;
-
- tmp = I915_READ(BLC_PWM_CTL2);
+ u32 ctl, ctl2, freq;
- /* Note that this can also get called through dpms changes. And
- * we don't track the backlight dpms state, hence check whether
- * we have to do anything first. */
- if (tmp & BLM_PWM_ENABLE)
- return;
+ ctl2 = I915_READ(BLC_PWM_CTL2);
+ if (ctl2 & BLM_PWM_ENABLE) {
+ WARN(1, "backlight already enabled\n");
+ ctl2 &= ~BLM_PWM_ENABLE;
+ I915_WRITE(BLC_PWM_CTL2, ctl2);
+ }
- tmp &= ~BLM_PIPE_SELECT;
- tmp |= BLM_PIPE(pipe);
- tmp &= ~BLM_PWM_ENABLE;
+ freq = panel->backlight.max;
+ if (panel->backlight.combination_mode)
+ freq /= 0xff;
- I915_WRITE(BLC_PWM_CTL2, tmp);
- POSTING_READ(BLC_PWM_CTL2);
- I915_WRITE(BLC_PWM_CTL2, tmp | BLM_PWM_ENABLE);
+ ctl = freq << 16;
+ I915_WRITE(BLC_PWM_CTL, ctl);
+ /* XXX: combine this into above write? */
intel_panel_actually_set_backlight(connector, panel->backlight.level);
+
+ ctl2 = BLM_PIPE(pipe);
+ if (panel->backlight.combination_mode)
+ ctl2 |= BLM_COMBINATION_MODE;
+ if (panel->backlight.active_low_pwm)
+ ctl2 |= BLM_POLARITY_I965;
+ I915_WRITE(BLC_PWM_CTL2, ctl2);
+ POSTING_READ(BLC_PWM_CTL2);
+ I915_WRITE(BLC_PWM_CTL2, ctl2 | BLM_PWM_ENABLE);
}
static void vlv_enable_backlight(struct intel_connector *connector)
@@ -799,23 +828,27 @@ static void vlv_enable_backlight(struct intel_connector *connector)
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_panel *panel = &connector->panel;
enum pipe pipe = intel_get_pipe_from_connector(connector);
- u32 tmp;
+ u32 ctl, ctl2;
- tmp = I915_READ(VLV_BLC_PWM_CTL2(pipe));
+ ctl2 = I915_READ(VLV_BLC_PWM_CTL2(pipe));
+ if (ctl2 & BLM_PWM_ENABLE) {
+ WARN(1, "backlight already enabled\n");
+ ctl2 &= ~BLM_PWM_ENABLE;
+ I915_WRITE(VLV_BLC_PWM_CTL2(pipe), ctl2);
+ }
- /* Note that this can also get called through dpms changes. And
- * we don't track the backlight dpms state, hence check whether
- * we have to do anything first. */
- if (tmp & BLM_PWM_ENABLE)
- return;
+ ctl = panel->backlight.max << 16;
+ I915_WRITE(VLV_BLC_PWM_CTL(pipe), ctl);
- tmp &= ~BLM_PWM_ENABLE;
+ /* XXX: combine this into above write? */
+ intel_panel_actually_set_backlight(connector, panel->backlight.level);
- I915_WRITE(VLV_BLC_PWM_CTL2(pipe), tmp);
+ ctl2 = 0;
+ if (panel->backlight.active_low_pwm)
+ ctl2 |= BLM_POLARITY_I965;
+ I915_WRITE(VLV_BLC_PWM_CTL2(pipe), ctl2);
POSTING_READ(VLV_BLC_PWM_CTL2(pipe));
- I915_WRITE(VLV_BLC_PWM_CTL2(pipe), tmp | BLM_PWM_ENABLE);
-
- intel_panel_actually_set_backlight(connector, panel->backlight.level);
+ I915_WRITE(VLV_BLC_PWM_CTL2(pipe), ctl2 | BLM_PWM_ENABLE);
}
void intel_panel_enable_backlight(struct intel_connector *connector)
--
1.7.10.4
More information about the Intel-gfx
mailing list