[Intel-gfx] [PATCH 11/13] drm/i915: do full backlight setup at enable time

[Imre Deak]

On Fri, 2013-11-08 at 16:49 +0200, Jani Nikula wrote:
> We should now have all the information we need to do a full
> initialization of the backlight registers.
> 
> Signed-off-by: Jani Nikula <jani.nikula at intel.com>
> ---
>  drivers/gpu/drm/i915/intel_panel.c |  145 ++++++++++++++++++++++--------------
>  1 file changed, 89 insertions(+), 56 deletions(-)
> 
> diff --git a/drivers/gpu/drm/i915/intel_panel.c b/drivers/gpu/drm/i915/intel_panel.c
> index 0e8f0a3..da088e3 100644
> --- a/drivers/gpu/drm/i915/intel_panel.c
> +++ b/drivers/gpu/drm/i915/intel_panel.c
> @@ -719,50 +719,71 @@ static void pch_enable_backlight(struct intel_connector *connector)
>  	enum pipe pipe = intel_get_pipe_from_connector(connector);
>  	enum transcoder cpu_transcoder =
>  		intel_pipe_to_cpu_transcoder(dev_priv, pipe);
> -	u32 tmp;
> -
> -	tmp = I915_READ(BLC_PWM_CPU_CTL2);
> +	u32 cpu_ctl2, pch_ctl1, pch_ctl2;
>  
> -	/* Note that this can also get called through dpms changes. And
> -	 * we don't track the backlight dpms state, hence check whether
> -	 * we have to do anything first. */
> -	if (tmp & BLM_PWM_ENABLE)
> -		return;
> +	cpu_ctl2 = I915_READ(BLC_PWM_CPU_CTL2);
> +	if (cpu_ctl2 & BLM_PWM_ENABLE) {
> +		WARN(1, "cpu backlight already enabled\n");
> +		cpu_ctl2 &= ~BLM_PWM_ENABLE;
> +		I915_WRITE(BLC_PWM_CPU_CTL2, cpu_ctl2);
> +	}
>  
> -	if (INTEL_INFO(dev)->num_pipes == 3)
> -		tmp &= ~BLM_PIPE_SELECT_IVB;
> -	else
> -		tmp &= ~BLM_PIPE_SELECT;
> +	pch_ctl1 = I915_READ(BLC_PWM_PCH_CTL1);
> +	if (pch_ctl1 & BLM_PCH_PWM_ENABLE) {
> +		DRM_DEBUG_KMS("pch backlight already enabled\n");
> +		pch_ctl1 &= ~BLM_PCH_PWM_ENABLE;
> +		I915_WRITE(BLC_PWM_PCH_CTL1, pch_ctl1);
> +	}
>  
>  	if (cpu_transcoder == TRANSCODER_EDP)
> -		tmp |= BLM_TRANSCODER_EDP;
> +		cpu_ctl2 = BLM_TRANSCODER_EDP;
>  	else
> -		tmp |= BLM_PIPE(cpu_transcoder);
> -	tmp &= ~BLM_PWM_ENABLE;
> -
> -	I915_WRITE(BLC_PWM_CPU_CTL2, tmp);
> +		cpu_ctl2 = BLM_PIPE(cpu_transcoder);
> +	I915_WRITE(BLC_PWM_CPU_CTL2, cpu_ctl2);
>  	POSTING_READ(BLC_PWM_CPU_CTL2);
> -	I915_WRITE(BLC_PWM_CPU_CTL2, tmp | BLM_PWM_ENABLE);
> -
> -	if (!(dev_priv->quirks & QUIRK_NO_PCH_PWM_ENABLE)) {
> -		tmp = I915_READ(BLC_PWM_PCH_CTL1);
> -		tmp |= BLM_PCH_PWM_ENABLE;
> -		tmp &= ~BLM_PCH_OVERRIDE_ENABLE;
> -		I915_WRITE(BLC_PWM_PCH_CTL1, tmp);
> -	}

Like in the previous patch, why is this removed? If the w/a is not
needed any more it should be a separate patch.

> +	I915_WRITE(BLC_PWM_CPU_CTL2, cpu_ctl2 | BLM_PWM_ENABLE);
>  
> -	/*
> -	 * Call below after setting BLC_PWM_CPU_CTL2 and BLC_PWM_PCH_CTL1.
> -	 * BLC_PWM_CPU_CTL may be cleared to zero automatically when these
> -	 * registers are set.
> -	 */
> +	/* This won't stick until the above enable. */
>  	intel_panel_actually_set_backlight(connector, panel->backlight.level);
> +
> +	pch_ctl2 = panel->backlight.max << 16;
> +	I915_WRITE(BLC_PWM_PCH_CTL2, pch_ctl2);
> +
> +	pch_ctl1 = 0;
> +	if (panel->backlight.active_low_pwm)
> +		pch_ctl1 |= BLM_PCH_POLARITY;
> +	I915_WRITE(BLC_PWM_PCH_CTL1, pch_ctl1);
> +	POSTING_READ(BLC_PWM_PCH_CTL1);
> +	I915_WRITE(BLC_PWM_PCH_CTL1, pch_ctl1 | BLM_PCH_PWM_ENABLE);
>  }
>  
>  static void i9xx_enable_backlight(struct intel_connector *connector)
>  {
> +	struct drm_device *dev = connector->base.dev;
> +	struct drm_i915_private *dev_priv = dev->dev_private;
>  	struct intel_panel *panel = &connector->panel;
> +	u32 ctl, freq;
>  
> +	ctl = I915_READ(BLC_PWM_CTL);
> +	if (ctl & BACKLIGHT_DUTY_CYCLE_MASK_PNV) {
> +		WARN(1, "backlight already enabled\n");
> +		I915_WRITE(BLC_PWM_CTL, 0);
> +	}
> +
> +	freq = panel->backlight.max;
> +	if (panel->backlight.combination_mode)
> +		freq /= 0xff;
> +
> +	ctl = freq << 17;
> +	if (IS_GEN2(dev) && panel->backlight.combination_mode)
> +		ctl |= BLM_LEGACY_MODE;
> +	if (IS_PINEVIEW(dev) && panel->backlight.active_low_pwm)
> +		ctl |= BLM_POLARITY_PNV;
> +
> +	I915_WRITE(BLC_PWM_CTL, ctl);
> +	POSTING_READ(BLC_PWM_CTL);
> +
> +	/* XXX: combine this into above write? */
>  	intel_panel_actually_set_backlight(connector, panel->backlight.level);
>  }
>  
> @@ -772,25 +793,33 @@ static void i965_enable_backlight(struct intel_connector *connector)
>  	struct drm_i915_private *dev_priv = dev->dev_private;
>  	struct intel_panel *panel = &connector->panel;
>  	enum pipe pipe = intel_get_pipe_from_connector(connector);
> -	u32 tmp;
> -
> -	tmp = I915_READ(BLC_PWM_CTL2);
> +	u32 ctl, ctl2, freq;
>  
> -	/* Note that this can also get called through dpms changes. And
> -	 * we don't track the backlight dpms state, hence check whether
> -	 * we have to do anything first. */
> -	if (tmp & BLM_PWM_ENABLE)
> -		return;
> +	ctl2 = I915_READ(BLC_PWM_CTL2);
> +	if (ctl2 & BLM_PWM_ENABLE) {
> +		WARN(1, "backlight already enabled\n");
> +		ctl2 &= ~BLM_PWM_ENABLE;
> +		I915_WRITE(BLC_PWM_CTL2, ctl2);
> +	}
>  
> -	tmp &= ~BLM_PIPE_SELECT;
> -	tmp |= BLM_PIPE(pipe);
> -	tmp &= ~BLM_PWM_ENABLE;
> +	freq = panel->backlight.max;
> +	if (panel->backlight.combination_mode)
> +		freq /= 0xff;
>  
> -	I915_WRITE(BLC_PWM_CTL2, tmp);
> -	POSTING_READ(BLC_PWM_CTL2);
> -	I915_WRITE(BLC_PWM_CTL2, tmp | BLM_PWM_ENABLE);
> +	ctl = freq << 16;
> +	I915_WRITE(BLC_PWM_CTL, ctl);
>  
> +	/* XXX: combine this into above write? */
>  	intel_panel_actually_set_backlight(connector, panel->backlight.level);
> +
> +	ctl2 = BLM_PIPE(pipe);
> +	if (panel->backlight.combination_mode)
> +		ctl2 |= BLM_COMBINATION_MODE;
> +	if (panel->backlight.active_low_pwm)
> +		ctl2 |= BLM_POLARITY_I965;
> +	I915_WRITE(BLC_PWM_CTL2, ctl2);
> +	POSTING_READ(BLC_PWM_CTL2);
> +	I915_WRITE(BLC_PWM_CTL2, ctl2 | BLM_PWM_ENABLE);
>  }
>  
>  static void vlv_enable_backlight(struct intel_connector *connector)
> @@ -799,23 +828,27 @@ static void vlv_enable_backlight(struct intel_connector *connector)
>  	struct drm_i915_private *dev_priv = dev->dev_private;
>  	struct intel_panel *panel = &connector->panel;
>  	enum pipe pipe = intel_get_pipe_from_connector(connector);
> -	u32 tmp;
> +	u32 ctl, ctl2;
>  
> -	tmp = I915_READ(VLV_BLC_PWM_CTL2(pipe));
> +	ctl2 = I915_READ(VLV_BLC_PWM_CTL2(pipe));
> +	if (ctl2 & BLM_PWM_ENABLE) {
> +		WARN(1, "backlight already enabled\n");
> +		ctl2 &= ~BLM_PWM_ENABLE;
> +		I915_WRITE(VLV_BLC_PWM_CTL2(pipe), ctl2);
> +	}
>  
> -	/* Note that this can also get called through dpms changes. And
> -	 * we don't track the backlight dpms state, hence check whether
> -	 * we have to do anything first. */
> -	if (tmp & BLM_PWM_ENABLE)
> -		return;
> +	ctl = panel->backlight.max << 16;
> +	I915_WRITE(VLV_BLC_PWM_CTL(pipe), ctl);
>  
> -	tmp &= ~BLM_PWM_ENABLE;
> +	/* XXX: combine this into above write? */
> +	intel_panel_actually_set_backlight(connector, panel->backlight.level);
>  
> -	I915_WRITE(VLV_BLC_PWM_CTL2(pipe), tmp);
> +	ctl2 = 0;
> +	if (panel->backlight.active_low_pwm)
> +		ctl2 |= BLM_POLARITY_I965;
> +	I915_WRITE(VLV_BLC_PWM_CTL2(pipe), ctl2);
>  	POSTING_READ(VLV_BLC_PWM_CTL2(pipe));
> -	I915_WRITE(VLV_BLC_PWM_CTL2(pipe), tmp | BLM_PWM_ENABLE);
> -
> -	intel_panel_actually_set_backlight(connector, panel->backlight.level);
> +	I915_WRITE(VLV_BLC_PWM_CTL2(pipe), ctl2 | BLM_PWM_ENABLE);
>  }
>  
>  void intel_panel_enable_backlight(struct intel_connector *connector)

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 490 bytes
Desc: This is a digitally signed message part
URL: <http://lists.freedesktop.org/archives/intel-gfx/attachments/20131113/696ceb8f/attachment.sig>