[Intel-gfx] [PATCH v2 1/4] drm/i915: Don't populate pipe_src_{w, h} multiple times

[Daniel Vetter]

On Tue, Oct 01, 2013 at 10:52:14PM +0300, ville.syrjala at linux.intel.com wrote:
> From: Ville Syrjälä <ville.syrjala at linux.intel.com>
> 
> If we ever end up doing the retry loop due to bandwidth constraints, we
> would rewrite pipe_src_{w,n} based on adjusted_mode timings. But by that
> time the encoder may have already replaced the adjusted_mode with a
> fixed panel mode, which would then corrupt pipe_src_{w,h}.
> 
> v2: Use requested_mode and slap on a big comment from Daniel
> 
> Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>

Queued for -next, thanks for the patch. I'll wait for Rodrigo to sanity
check the next patch, and the third one doesn't apply right away (and I'm
lazy).
-Daniel

> ---
>  drivers/gpu/drm/i915/intel_display.c | 16 ++++++++++++----
>  1 file changed, 12 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> index a91f20a..4fa97a5 100644
> --- a/drivers/gpu/drm/i915/intel_display.c
> +++ b/drivers/gpu/drm/i915/intel_display.c
> @@ -8472,6 +8472,18 @@ intel_modeset_pipe_config(struct drm_crtc *crtc,
>  	if (plane_bpp < 0)
>  		goto fail;
>  
> +	/*
> +	 * Determine the real pipe dimensions. Note that stereo modes can
> +	 * increase the actual pipe size due to the frame doubling and
> +	 * insertion of additional space for blanks between the frame. This
> +	 * is stored in the crtc timings. We use the requested mode to do this
> +	 * computation to clearly distinguish it from the adjusted mode, which
> +	 * can be changed by the connectors in the below retry loop.
> +	 */
> +	drm_mode_set_crtcinfo(&pipe_config->requested_mode, CRTC_STEREO_DOUBLE);
> +	pipe_config->pipe_src_w = pipe_config->requested_mode.crtc_hdisplay;
> +	pipe_config->pipe_src_h = pipe_config->requested_mode.crtc_vdisplay;
> +
>  encoder_retry:
>  	/* Ensure the port clock defaults are reset when retrying. */
>  	pipe_config->port_clock = 0;
> @@ -8480,10 +8492,6 @@ encoder_retry:
>  	/* Fill in default crtc timings, allow encoders to overwrite them. */
>  	drm_mode_set_crtcinfo(&pipe_config->adjusted_mode, CRTC_STEREO_DOUBLE);
>  
> -	/* set_crtcinfo() may have adjusted hdisplay/vdisplay */
> -	pipe_config->pipe_src_w = pipe_config->adjusted_mode.crtc_hdisplay;
> -	pipe_config->pipe_src_h = pipe_config->adjusted_mode.crtc_vdisplay;
> -
>  	/* Pass our mode to the connectors and the CRTC to give them a chance to
>  	 * adjust it according to limitations or connector properties, and also
>  	 * a chance to reject the mode entirely.
> -- 
> 1.8.1.5
> 

-- 
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch