[Intel-gfx] [RFC PATCH 01/18] drm/i915: Removing the eDP specific DRRS implementation
Ramalingam C
ramalingam.c at intel.com
Fri Jun 26 06:51:45 PDT 2015
EDP specific DRRS implementation is removed to implement a
generic DRRS stack extentable accross the supportable encoders.
Signed-off-by: Ramalingam C <ramalingam.c at intel.com>
---
drivers/gpu/drm/i915/i915_debugfs.c | 110 ---------
drivers/gpu/drm/i915/i915_drv.h | 22 --
drivers/gpu/drm/i915/intel_ddi.c | 2 -
drivers/gpu/drm/i915/intel_dp.c | 392 ------------------------------
drivers/gpu/drm/i915/intel_drv.h | 5 -
drivers/gpu/drm/i915/intel_frontbuffer.c | 2 -
6 files changed, 533 deletions(-)
diff --git a/drivers/gpu/drm/i915/i915_debugfs.c b/drivers/gpu/drm/i915/i915_debugfs.c
index c49fe2a..7dbf170 100644
--- a/drivers/gpu/drm/i915/i915_debugfs.c
+++ b/drivers/gpu/drm/i915/i915_debugfs.c
@@ -2962,115 +2962,6 @@ static int i915_ddb_info(struct seq_file *m, void *unused)
return 0;
}
-static void drrs_status_per_crtc(struct seq_file *m,
- struct drm_device *dev, struct intel_crtc *intel_crtc)
-{
- struct intel_encoder *intel_encoder;
- struct drm_i915_private *dev_priv = dev->dev_private;
- struct i915_drrs *drrs = &dev_priv->drrs;
- int vrefresh = 0;
-
- for_each_encoder_on_crtc(dev, &intel_crtc->base, intel_encoder) {
- /* Encoder connected on this CRTC */
- switch (intel_encoder->type) {
- case INTEL_OUTPUT_EDP:
- seq_puts(m, "eDP:\n");
- break;
- case INTEL_OUTPUT_DSI:
- seq_puts(m, "DSI:\n");
- break;
- case INTEL_OUTPUT_HDMI:
- seq_puts(m, "HDMI:\n");
- break;
- case INTEL_OUTPUT_DISPLAYPORT:
- seq_puts(m, "DP:\n");
- break;
- default:
- seq_printf(m, "Other encoder (id=%d).\n",
- intel_encoder->type);
- return;
- }
- }
-
- if (dev_priv->vbt.drrs_type == STATIC_DRRS_SUPPORT)
- seq_puts(m, "\tVBT: DRRS_type: Static");
- else if (dev_priv->vbt.drrs_type == SEAMLESS_DRRS_SUPPORT)
- seq_puts(m, "\tVBT: DRRS_type: Seamless");
- else if (dev_priv->vbt.drrs_type == DRRS_NOT_SUPPORTED)
- seq_puts(m, "\tVBT: DRRS_type: None");
- else
- seq_puts(m, "\tVBT: DRRS_type: FIXME: Unrecognized Value");
-
- seq_puts(m, "\n\n");
-
- if (to_intel_crtc_state(intel_crtc->base.state)->has_drrs) {
- struct intel_panel *panel;
-
- mutex_lock(&drrs->mutex);
- /* DRRS Supported */
- seq_puts(m, "\tDRRS Supported: Yes\n");
-
- /* disable_drrs() will make drrs->dp NULL */
- if (!drrs->dp) {
- seq_puts(m, "Idleness DRRS: Disabled");
- mutex_unlock(&drrs->mutex);
- return;
- }
-
- panel = &drrs->dp->attached_connector->panel;
- seq_printf(m, "\t\tBusy_frontbuffer_bits: 0x%X",
- drrs->busy_frontbuffer_bits);
-
- seq_puts(m, "\n\t\t");
- if (drrs->refresh_rate_type == DRRS_HIGH_RR) {
- seq_puts(m, "DRRS_State: DRRS_HIGH_RR\n");
- vrefresh = panel->fixed_mode->vrefresh;
- } else if (drrs->refresh_rate_type == DRRS_LOW_RR) {
- seq_puts(m, "DRRS_State: DRRS_LOW_RR\n");
- vrefresh = panel->downclock_mode->vrefresh;
- } else {
- seq_printf(m, "DRRS_State: Unknown(%d)\n",
- drrs->refresh_rate_type);
- mutex_unlock(&drrs->mutex);
- return;
- }
- seq_printf(m, "\t\tVrefresh: %d", vrefresh);
-
- seq_puts(m, "\n\t\t");
- mutex_unlock(&drrs->mutex);
- } else {
- /* DRRS not supported. Print the VBT parameter*/
- seq_puts(m, "\tDRRS Supported : No");
- }
- seq_puts(m, "\n");
-}
-
-static int i915_drrs_status(struct seq_file *m, void *unused)
-{
- struct drm_info_node *node = m->private;
- struct drm_device *dev = node->minor->dev;
- struct intel_crtc *intel_crtc;
- int active_crtc_cnt = 0;
-
- for_each_intel_crtc(dev, intel_crtc) {
- drm_modeset_lock(&intel_crtc->base.mutex, NULL);
-
- if (intel_crtc->base.state->active) {
- active_crtc_cnt++;
- seq_printf(m, "\nCRTC %d: ", active_crtc_cnt);
-
- drrs_status_per_crtc(m, dev, intel_crtc);
- }
-
- drm_modeset_unlock(&intel_crtc->base.mutex);
- }
-
- if (!active_crtc_cnt)
- seq_puts(m, "No active crtc found\n");
-
- return 0;
-}
-
struct pipe_crc_info {
const char *name;
struct drm_device *dev;
@@ -5048,7 +4939,6 @@ static const struct drm_info_list i915_debugfs_list[] = {
{"i915_wa_registers", i915_wa_registers, 0},
{"i915_ddb_info", i915_ddb_info, 0},
{"i915_sseu_status", i915_sseu_status, 0},
- {"i915_drrs_status", i915_drrs_status, 0},
{"i915_rps_boost_info", i915_rps_boost_info, 0},
};
#define I915_DEBUGFS_ENTRIES ARRAY_SIZE(i915_debugfs_list)
diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 491ef0c..922dd68 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -930,33 +930,12 @@ struct i915_fbc {
} no_fbc_reason;
};
-/**
- * HIGH_RR is the highest eDP panel refresh rate read from EDID
- * LOW_RR is the lowest eDP panel refresh rate found from EDID
- * parsing for same resolution.
- */
-enum drrs_refresh_rate_type {
- DRRS_HIGH_RR,
- DRRS_LOW_RR,
- DRRS_MAX_RR, /* RR count */
-};
-
enum drrs_support_type {
DRRS_NOT_SUPPORTED = 0,
STATIC_DRRS_SUPPORT = 1,
SEAMLESS_DRRS_SUPPORT = 2
};
-struct intel_dp;
-struct i915_drrs {
- struct mutex mutex;
- struct delayed_work work;
- struct intel_dp *dp;
- unsigned busy_frontbuffer_bits;
- enum drrs_refresh_rate_type refresh_rate_type;
- enum drrs_support_type type;
-};
-
struct i915_psr {
struct mutex lock;
bool sink_support;
@@ -1718,7 +1697,6 @@ struct drm_i915_private {
struct i915_hotplug hotplug;
struct i915_fbc fbc;
- struct i915_drrs drrs;
struct intel_opregion opregion;
struct intel_vbt_data vbt;
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index 31b29e8..75afbd7 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -2012,7 +2012,6 @@ static void intel_enable_ddi(struct intel_encoder *intel_encoder)
intel_edp_backlight_on(intel_dp);
intel_psr_enable(intel_dp);
- intel_edp_drrs_enable(intel_dp);
}
if (intel_crtc->config->has_audio) {
@@ -2038,7 +2037,6 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder)
if (type == INTEL_OUTPUT_EDP) {
struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
- intel_edp_drrs_disable(intel_dp);
intel_psr_disable(intel_dp);
intel_edp_backlight_off(intel_dp);
}
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index f52eef1..738e98e 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -1483,15 +1483,6 @@ found:
pipe_config->port_clock,
&pipe_config->dp_m_n);
- if (intel_connector->panel.downclock_mode != NULL &&
- dev_priv->drrs.type == SEAMLESS_DRRS_SUPPORT) {
- pipe_config->has_drrs = true;
- intel_link_compute_m_n(bpp, lane_count,
- intel_connector->panel.downclock_mode->clock,
- pipe_config->port_clock,
- &pipe_config->dp_m2_n2);
- }
-
if (IS_SKYLAKE(dev) && is_edp(intel_dp))
skl_edp_set_pll_config(pipe_config, common_rates[clock]);
else if (IS_BROXTON(dev))
@@ -5254,387 +5245,6 @@ intel_dp_init_panel_power_sequencer_registers(struct drm_device *dev,
I915_READ(pp_div_reg));
}
-/**
- * intel_dp_set_drrs_state - program registers for RR switch to take effect
- * @dev: DRM device
- * @refresh_rate: RR to be programmed
- *
- * This function gets called when refresh rate (RR) has to be changed from
- * one frequency to another. Switches can be between high and low RR
- * supported by the panel or to any other RR based on media playback (in
- * this case, RR value needs to be passed from user space).
- *
- * The caller of this function needs to take a lock on dev_priv->drrs.
- */
-static void intel_dp_set_drrs_state(struct drm_device *dev, int refresh_rate)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
- struct intel_encoder *encoder;
- struct intel_digital_port *dig_port = NULL;
- struct intel_dp *intel_dp = dev_priv->drrs.dp;
- struct intel_crtc_state *config = NULL;
- struct intel_crtc *intel_crtc = NULL;
- u32 reg, val;
- enum drrs_refresh_rate_type index = DRRS_HIGH_RR;
-
- if (refresh_rate <= 0) {
- DRM_DEBUG_KMS("Refresh rate should be positive non-zero.\n");
- return;
- }
-
- if (intel_dp == NULL) {
- DRM_DEBUG_KMS("DRRS not supported.\n");
- return;
- }
-
- /*
- * FIXME: This needs proper synchronization with psr state for some
- * platforms that cannot have PSR and DRRS enabled at the same time.
- */
-
- dig_port = dp_to_dig_port(intel_dp);
- encoder = &dig_port->base;
- intel_crtc = to_intel_crtc(encoder->base.crtc);
-
- if (!intel_crtc) {
- DRM_DEBUG_KMS("DRRS: intel_crtc not initialized\n");
- return;
- }
-
- config = intel_crtc->config;
-
- if (dev_priv->drrs.type < SEAMLESS_DRRS_SUPPORT) {
- DRM_DEBUG_KMS("Only Seamless DRRS supported.\n");
- return;
- }
-
- if (intel_dp->attached_connector->panel.downclock_mode->vrefresh ==
- refresh_rate)
- index = DRRS_LOW_RR;
-
- if (index == dev_priv->drrs.refresh_rate_type) {
- DRM_DEBUG_KMS(
- "DRRS requested for previously set RR...ignoring\n");
- return;
- }
-
- if (!intel_crtc->active) {
- DRM_DEBUG_KMS("eDP encoder disabled. CRTC not Active\n");
- return;
- }
-
- if (INTEL_INFO(dev)->gen >= 8 && !IS_CHERRYVIEW(dev)) {
- switch (index) {
- case DRRS_HIGH_RR:
- intel_dp_set_m_n(intel_crtc, M1_N1);
- break;
- case DRRS_LOW_RR:
- intel_dp_set_m_n(intel_crtc, M2_N2);
- break;
- case DRRS_MAX_RR:
- default:
- DRM_ERROR("Unsupported refreshrate type\n");
- }
- } else if (INTEL_INFO(dev)->gen > 6) {
- reg = PIPECONF(intel_crtc->config->cpu_transcoder);
- val = I915_READ(reg);
-
- if (index > DRRS_HIGH_RR) {
- if (IS_VALLEYVIEW(dev))
- val |= PIPECONF_EDP_RR_MODE_SWITCH_VLV;
- else
- val |= PIPECONF_EDP_RR_MODE_SWITCH;
- } else {
- if (IS_VALLEYVIEW(dev))
- val &= ~PIPECONF_EDP_RR_MODE_SWITCH_VLV;
- else
- val &= ~PIPECONF_EDP_RR_MODE_SWITCH;
- }
- I915_WRITE(reg, val);
- }
-
- dev_priv->drrs.refresh_rate_type = index;
-
- DRM_DEBUG_KMS("eDP Refresh Rate set to : %dHz\n", refresh_rate);
-}
-
-/**
- * intel_edp_drrs_enable - init drrs struct if supported
- * @intel_dp: DP struct
- *
- * Initializes frontbuffer_bits and drrs.dp
- */
-void intel_edp_drrs_enable(struct intel_dp *intel_dp)
-{
- struct drm_device *dev = intel_dp_to_dev(intel_dp);
- struct drm_i915_private *dev_priv = dev->dev_private;
- struct intel_digital_port *dig_port = dp_to_dig_port(intel_dp);
- struct drm_crtc *crtc = dig_port->base.base.crtc;
- struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
-
- if (!intel_crtc->config->has_drrs) {
- DRM_DEBUG_KMS("Panel doesn't support DRRS\n");
- return;
- }
-
- mutex_lock(&dev_priv->drrs.mutex);
- if (WARN_ON(dev_priv->drrs.dp)) {
- DRM_ERROR("DRRS already enabled\n");
- goto unlock;
- }
-
- dev_priv->drrs.busy_frontbuffer_bits = 0;
-
- dev_priv->drrs.dp = intel_dp;
-
-unlock:
- mutex_unlock(&dev_priv->drrs.mutex);
-}
-
-/**
- * intel_edp_drrs_disable - Disable DRRS
- * @intel_dp: DP struct
- *
- */
-void intel_edp_drrs_disable(struct intel_dp *intel_dp)
-{
- struct drm_device *dev = intel_dp_to_dev(intel_dp);
- struct drm_i915_private *dev_priv = dev->dev_private;
- struct intel_digital_port *dig_port = dp_to_dig_port(intel_dp);
- struct drm_crtc *crtc = dig_port->base.base.crtc;
- struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
-
- if (!intel_crtc->config->has_drrs)
- return;
-
- mutex_lock(&dev_priv->drrs.mutex);
- if (!dev_priv->drrs.dp) {
- mutex_unlock(&dev_priv->drrs.mutex);
- return;
- }
-
- if (dev_priv->drrs.refresh_rate_type == DRRS_LOW_RR)
- intel_dp_set_drrs_state(dev_priv->dev,
- intel_dp->attached_connector->panel.
- fixed_mode->vrefresh);
-
- dev_priv->drrs.dp = NULL;
- mutex_unlock(&dev_priv->drrs.mutex);
-
- cancel_delayed_work_sync(&dev_priv->drrs.work);
-}
-
-static void intel_edp_drrs_downclock_work(struct work_struct *work)
-{
- struct drm_i915_private *dev_priv =
- container_of(work, typeof(*dev_priv), drrs.work.work);
- struct intel_dp *intel_dp;
-
- mutex_lock(&dev_priv->drrs.mutex);
-
- intel_dp = dev_priv->drrs.dp;
-
- if (!intel_dp)
- goto unlock;
-
- /*
- * The delayed work can race with an invalidate hence we need to
- * recheck.
- */
-
- if (dev_priv->drrs.busy_frontbuffer_bits)
- goto unlock;
-
- if (dev_priv->drrs.refresh_rate_type != DRRS_LOW_RR)
- intel_dp_set_drrs_state(dev_priv->dev,
- intel_dp->attached_connector->panel.
- downclock_mode->vrefresh);
-
-unlock:
- mutex_unlock(&dev_priv->drrs.mutex);
-}
-
-/**
- * intel_edp_drrs_invalidate - Disable Idleness DRRS
- * @dev: DRM device
- * @frontbuffer_bits: frontbuffer plane tracking bits
- *
- * This function gets called everytime rendering on the given planes start.
- * Hence DRRS needs to be Upclocked, i.e. (LOW_RR -> HIGH_RR).
- *
- * Dirty frontbuffers relevant to DRRS are tracked in busy_frontbuffer_bits.
- */
-void intel_edp_drrs_invalidate(struct drm_device *dev,
- unsigned frontbuffer_bits)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
- struct drm_crtc *crtc;
- enum pipe pipe;
-
- if (dev_priv->drrs.type == DRRS_NOT_SUPPORTED)
- return;
-
- cancel_delayed_work(&dev_priv->drrs.work);
-
- mutex_lock(&dev_priv->drrs.mutex);
- if (!dev_priv->drrs.dp) {
- mutex_unlock(&dev_priv->drrs.mutex);
- return;
- }
-
- crtc = dp_to_dig_port(dev_priv->drrs.dp)->base.base.crtc;
- pipe = to_intel_crtc(crtc)->pipe;
-
- /* invalidate means busy screen hence upclock */
- if (dev_priv->drrs.refresh_rate_type == DRRS_LOW_RR) {
- intel_dp_set_drrs_state(dev_priv->dev,
- dev_priv->drrs.dp->attached_connector->panel.
- fixed_mode->vrefresh);
- }
-
- frontbuffer_bits &= INTEL_FRONTBUFFER_ALL_MASK(pipe);
-
- dev_priv->drrs.busy_frontbuffer_bits |= frontbuffer_bits;
- mutex_unlock(&dev_priv->drrs.mutex);
-}
-
-/**
- * intel_edp_drrs_flush - Restart Idleness DRRS
- * @dev: DRM device
- * @frontbuffer_bits: frontbuffer plane tracking bits
- *
- * This function gets called every time rendering on the given planes has
- * completed or flip on a crtc is completed. So DRRS should be upclocked
- * (LOW_RR -> HIGH_RR). And also Idleness detection should be started again,
- * if no other planes are dirty.
- *
- * Dirty frontbuffers relevant to DRRS are tracked in busy_frontbuffer_bits.
- */
-void intel_edp_drrs_flush(struct drm_device *dev,
- unsigned frontbuffer_bits)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
- struct drm_crtc *crtc;
- enum pipe pipe;
-
- if (dev_priv->drrs.type == DRRS_NOT_SUPPORTED)
- return;
-
- cancel_delayed_work(&dev_priv->drrs.work);
-
- mutex_lock(&dev_priv->drrs.mutex);
- if (!dev_priv->drrs.dp) {
- mutex_unlock(&dev_priv->drrs.mutex);
- return;
- }
-
- crtc = dp_to_dig_port(dev_priv->drrs.dp)->base.base.crtc;
- pipe = to_intel_crtc(crtc)->pipe;
- dev_priv->drrs.busy_frontbuffer_bits &= ~frontbuffer_bits;
-
- /* flush means busy screen hence upclock */
- if (dev_priv->drrs.refresh_rate_type == DRRS_LOW_RR)
- intel_dp_set_drrs_state(dev_priv->dev,
- dev_priv->drrs.dp->attached_connector->panel.
- fixed_mode->vrefresh);
-
- /*
- * flush also means no more activity hence schedule downclock, if all
- * other fbs are quiescent too
- */
- if (!dev_priv->drrs.busy_frontbuffer_bits)
- schedule_delayed_work(&dev_priv->drrs.work,
- msecs_to_jiffies(1000));
- mutex_unlock(&dev_priv->drrs.mutex);
-}
-
-/**
- * DOC: Display Refresh Rate Switching (DRRS)
- *
- * Display Refresh Rate Switching (DRRS) is a power conservation feature
- * which enables swtching between low and high refresh rates,
- * dynamically, based on the usage scenario. This feature is applicable
- * for internal panels.
- *
- * Indication that the panel supports DRRS is given by the panel EDID, which
- * would list multiple refresh rates for one resolution.
- *
- * DRRS is of 2 types - static and seamless.
- * Static DRRS involves changing refresh rate (RR) by doing a full modeset
- * (may appear as a blink on screen) and is used in dock-undock scenario.
- * Seamless DRRS involves changing RR without any visual effect to the user
- * and can be used during normal system usage. This is done by programming
- * certain registers.
- *
- * Support for static/seamless DRRS may be indicated in the VBT based on
- * inputs from the panel spec.
- *
- * DRRS saves power by switching to low RR based on usage scenarios.
- *
- * eDP DRRS:-
- * The implementation is based on frontbuffer tracking implementation.
- * When there is a disturbance on the screen triggered by user activity or a
- * periodic system activity, DRRS is disabled (RR is changed to high RR).
- * When there is no movement on screen, after a timeout of 1 second, a switch
- * to low RR is made.
- * For integration with frontbuffer tracking code,
- * intel_edp_drrs_invalidate() and intel_edp_drrs_flush() are called.
- *
- * DRRS can be further extended to support other internal panels and also
- * the scenario of video playback wherein RR is set based on the rate
- * requested by userspace.
- */
-
-/**
- * intel_dp_drrs_init - Init basic DRRS work and mutex.
- * @intel_connector: eDP connector
- * @fixed_mode: preferred mode of panel
- *
- * This function is called only once at driver load to initialize basic
- * DRRS stuff.
- *
- * Returns:
- * Downclock mode if panel supports it, else return NULL.
- * DRRS support is determined by the presence of downclock mode (apart
- * from VBT setting).
- */
-static struct drm_display_mode *
-intel_dp_drrs_init(struct intel_connector *intel_connector,
- struct drm_display_mode *fixed_mode)
-{
- struct drm_connector *connector = &intel_connector->base;
- struct drm_device *dev = connector->dev;
- struct drm_i915_private *dev_priv = dev->dev_private;
- struct drm_display_mode *downclock_mode = NULL;
-
- INIT_DELAYED_WORK(&dev_priv->drrs.work, intel_edp_drrs_downclock_work);
- mutex_init(&dev_priv->drrs.mutex);
-
- if (INTEL_INFO(dev)->gen <= 6) {
- DRM_DEBUG_KMS("DRRS supported for Gen7 and above\n");
- return NULL;
- }
-
- if (dev_priv->vbt.drrs_type != SEAMLESS_DRRS_SUPPORT) {
- DRM_DEBUG_KMS("VBT doesn't support DRRS\n");
- return NULL;
- }
-
- downclock_mode = intel_find_panel_downclock
- (dev, fixed_mode, connector);
-
- if (!downclock_mode) {
- DRM_DEBUG_KMS("Downclock mode is not found. DRRS not supported\n");
- return NULL;
- }
-
- dev_priv->drrs.type = dev_priv->vbt.drrs_type;
-
- dev_priv->drrs.refresh_rate_type = DRRS_HIGH_RR;
- DRM_DEBUG_KMS("seamless DRRS supported for eDP panel.\n");
- return downclock_mode;
-}
-
static bool intel_edp_init_connector(struct intel_dp *intel_dp,
struct intel_connector *intel_connector)
{
@@ -5696,8 +5306,6 @@ static bool intel_edp_init_connector(struct intel_dp *intel_dp,
list_for_each_entry(scan, &connector->probed_modes, head) {
if ((scan->type & DRM_MODE_TYPE_PREFERRED)) {
fixed_mode = drm_mode_duplicate(dev, scan);
- downclock_mode = intel_dp_drrs_init(
- intel_connector, fixed_mode);
break;
}
}
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index bcafefc..e2f534a 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -1198,11 +1198,6 @@ void intel_dp_hot_plug(struct intel_encoder *intel_encoder);
void vlv_power_sequencer_reset(struct drm_i915_private *dev_priv);
uint32_t intel_dp_pack_aux(const uint8_t *src, int src_bytes);
void intel_plane_destroy(struct drm_plane *plane);
-void intel_edp_drrs_enable(struct intel_dp *intel_dp);
-void intel_edp_drrs_disable(struct intel_dp *intel_dp);
-void intel_edp_drrs_invalidate(struct drm_device *dev,
- unsigned frontbuffer_bits);
-void intel_edp_drrs_flush(struct drm_device *dev, unsigned frontbuffer_bits);
/* intel_dp_mst.c */
int intel_dp_mst_encoder_init(struct intel_digital_port *intel_dig_port, int conn_id);
diff --git a/drivers/gpu/drm/i915/intel_frontbuffer.c b/drivers/gpu/drm/i915/intel_frontbuffer.c
index 57095f5..249d0b3 100644
--- a/drivers/gpu/drm/i915/intel_frontbuffer.c
+++ b/drivers/gpu/drm/i915/intel_frontbuffer.c
@@ -154,7 +154,6 @@ void intel_fb_obj_invalidate(struct drm_i915_gem_object *obj,
intel_mark_fb_busy(dev, obj->frontbuffer_bits, ring);
intel_psr_invalidate(dev, obj->frontbuffer_bits);
- intel_edp_drrs_invalidate(dev, obj->frontbuffer_bits);
intel_fbc_invalidate(dev_priv, obj->frontbuffer_bits, origin);
}
@@ -181,7 +180,6 @@ void intel_frontbuffer_flush(struct drm_device *dev,
intel_mark_fb_busy(dev, frontbuffer_bits, NULL);
- intel_edp_drrs_flush(dev, frontbuffer_bits);
intel_psr_flush(dev, frontbuffer_bits);
intel_fbc_flush(dev_priv, frontbuffer_bits);
}
--
1.7.9.5
More information about the Intel-gfx
mailing list