[Intel-gfx] [PATCH 8/9] drm/i915: Use state->visible in wm calculation

[Ville Syrjälä]

On Tue, Mar 10, 2015 at 10:19:56AM -0700, Matt Roper wrote:
> On Tue, Mar 10, 2015 at 01:15:28PM +0200, ville.syrjala at linux.intel.com wrote:
> > From: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > 
> > Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
> 
> The actual diff here needs to be regenerated since my patch got merged
> and changed this area of the code, but your final solution looks right
> to me.  The main difference between your patch here and what got merged
> yesterday is that your patch starts using state->visible rather than
> state->fb, which is the right move to make.
> 
> So assuming you rebase your changes onto the latest code,
> Reviewed-by: Matt Roper <matthew.d.roper at intel.com>

Yep, I was expecting a slight conflict here since you were working in the
same vicinity. So I'll respin this one on top of the latest stuff.

And I should change the vlv/chv code while I'm at it...

> 
> > ---
> >  drivers/gpu/drm/i915/intel_pm.c | 24 +++++++++++++++++-------
> >  1 file changed, 17 insertions(+), 7 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
> > index a06a2c7..499e054 100644
> > --- a/drivers/gpu/drm/i915/intel_pm.c
> > +++ b/drivers/gpu/drm/i915/intel_pm.c
> > @@ -1955,6 +1955,7 @@ static void ilk_compute_wm_parameters(struct drm_crtc *crtc,
> >  	struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
> >  	enum pipe pipe = intel_crtc->pipe;
> >  	struct drm_plane *plane;
> > +	const struct intel_plane_state *state;
> >  
> >  	if (!intel_crtc->active)
> >  		return;
> > @@ -1962,13 +1963,22 @@ static void ilk_compute_wm_parameters(struct drm_crtc *crtc,
> >  	p->active = true;
> >  	p->pipe_htotal = intel_crtc->config->base.adjusted_mode.crtc_htotal;
> >  	p->pixel_rate = ilk_pipe_pixel_rate(dev, crtc);
> > -	p->pri.bytes_per_pixel = crtc->primary->state->fb->bits_per_pixel / 8;
> > -	p->cur.bytes_per_pixel = 4;
> > -	p->pri.horiz_pixels = intel_crtc->config->pipe_src_w;
> > -	p->cur.horiz_pixels = intel_crtc->base.cursor->state->crtc_w;
> > -	/* TODO: for now, assume primary and cursor planes are always enabled. */
> > -	p->pri.enabled = true;
> > -	p->cur.enabled = true;
> > +
> > +	state = to_intel_plane_state(crtc->primary->state);
> > +	if (state->visible) {
> > +		p->pri.enabled = true;
> > +		p->pri.bytes_per_pixel =
> > +			drm_format_plane_cpp(state->base.fb->pixel_format, 0);
> > +		p->pri.horiz_pixels = drm_rect_width(&state->dst);
> > +	}
> > +
> > +	state = to_intel_plane_state(crtc->cursor->state);
> > +	if (state->visible) {
> > +		p->cur.enabled = true;
> > +		p->cur.bytes_per_pixel =
> > +			drm_format_plane_cpp(state->base.fb->pixel_format, 0);
> > +		p->cur.horiz_pixels = state->base.crtc_w;
> > +	}
> >  
> >  	drm_for_each_legacy_plane(plane, &dev->mode_config.plane_list) {
> >  		struct intel_plane *intel_plane = to_intel_plane(plane);
> > -- 
> > 2.0.5
> > 
> > _______________________________________________
> > Intel-gfx mailing list
> > Intel-gfx at lists.freedesktop.org
> > http://lists.freedesktop.org/mailman/listinfo/intel-gfx
> 
> -- 
> Matt Roper
> Graphics Software Engineer
> IoTG Platform Enabling & Development
> Intel Corporation
> (916) 356-2795

-- 
Ville Syrjälä
Intel OTC