[Intel-gfx] [PATCH 1/2] drm : adds Y-coordinate and Colorimetry Format

Jani Nikula jani.nikula at linux.intel.com
Thu Dec 22 11:05:18 UTC 2016


On Wed, 21 Dec 2016, vathsala nagaraju <vathsala.nagaraju at intel.com> wrote:
> PSR2 vsc revision number hb2( as per table 6-11)is updated to
> 4 or 5 based on Y cordinate and Colorimetry Format as below
> 04h = 3D stereo + PSR/PSR2 + Y-coordinate.
> 05h = -3D stereo- + PSR/PSR2 + Y-coordinate + Pixel Encoding/Colorimetry
> Format indication. A DP Source device is allowed to indicate the pixel
> encoding/colorimetry format to the DP Sink device with VSC SDP only when
> the DP Sink device supports it (
> i.e.,VSC_SDP_EXTENSION_FOR_COLORIMETRY_SUPPORTED bit in the
> DPRX_FEATURE_ENUMERATION_LIST register (DPCD Address 02210h, bit 3;
> is set to 1).
>
> Cc: Rodrigo Vivi <rodrigo.vivi at intel.com>
> Cc: Jim Bride <jim.bride at linux.intel.com>
> Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju at intel.com>
> ---
>  include/drm/drm_dp_helper.h | 4 ++++
>  1 file changed, 4 insertions(+)
>
> diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
> index 55bbeb0..b3d2858 100644
> --- a/include/drm/drm_dp_helper.h
> +++ b/include/drm/drm_dp_helper.h
> @@ -194,6 +194,7 @@
>  # define DP_PSR_SETUP_TIME_0                (6 << 1)
>  # define DP_PSR_SETUP_TIME_MASK             (7 << 1)
>  # define DP_PSR_SETUP_TIME_SHIFT            1
> +# define DP_PSR_Y_COORDINATE               (1 << 4)  /* eDP 1.4 */

Do you think DP_PSR2_SU_Y_COORDINATE_REQUIRED would be too long? It was
introduced in eDP 1.4a to be specific.

While adding stuff here, please also add DP_PSR2_SU_GRANULARITY_REQUIRED
from eDP v1.4b.

>  
>  /*
>   * 0x80-0x8f describe downstream port capabilities, but there are two layouts
> @@ -568,6 +569,9 @@
>  #define DP_RECEIVER_ALPM_STATUS		    0x200b  /* eDP 1.4 */
>  # define DP_ALPM_LOCK_TIMEOUT_ERROR	    (1 << 0)
>  
> +#define DPRX_FEATURE_ENUMERATION_LIST	    0x2210
> +# define VSC_SDP_EXT_FOR_COLORIMETRY_SUPPORTED (1 << 3)
> +

All DPCD register and bit defs in this file are prefixed with
DP_. Please add that.

If you're going through the trouble of adding the bits from the spec,
you might as well add all of the bits in this register, and I could
review them at no extra trouble, instead of everyone adding bits and
pieces a little bit at a time. Saves everyone some trouble.

BR,
Jani.


>  /* DP 1.2 Sideband message defines */
>  /* peer device type - DP 1.2a Table 2-92 */
>  #define DP_PEER_DEVICE_NONE		0x0

-- 
Jani Nikula, Intel Open Source Technology Center


More information about the Intel-gfx mailing list