[Intel-gfx] [PATCH 3/6] drm/i915: Only use one link bw config for MST topologies

[Lyude Paul]

When a DP MST link needs retraining, sometimes the hub will detect that
the current link bw config is impossible and will update it's RX caps in
the DPCD to reflect the new maximum link rate. Currently, we make the
assumption that the RX caps in the dpcd will never change like this.
This means if the sink changes it's RX caps after we've already set up
an MST link and we attempt to add or remove another sink from the
topology, we could put ourselves into an invalid state where we've tried
to configure different sinks on the same MST topology with different
link rates. We could also run into this situation if a sink reports a
higher link rate after suspend, usually from us having trained it with a
fallback bw configuration before suspending.

So: "lock" the bw config by only using the max DP link rate/lane count
on the first modeset for an MST topology. For every modeset following,
we instead use the last configured link bw for this topology. We only
unlock the bw config when we've detected a new MST sink.

Signed-off-by: Lyude Paul <lyude at redhat.com>
Cc: Manasi Navare <manasi.d.navare at intel.com>
Cc: Ville Syrjälä <ville.syrjala at linux.intel.com>
---
 drivers/gpu/drm/i915/intel_dp.c     | 11 +++++++++--
 drivers/gpu/drm/i915/intel_dp_mst.c | 22 +++++++++++++++-------
 drivers/gpu/drm/i915/intel_drv.h    |  6 ++++++
 3 files changed, 30 insertions(+), 9 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 5abf0c95725a..5645a194de92 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -3871,18 +3871,25 @@ intel_dp_can_mst(struct intel_dp *intel_dp)
 static void
 intel_dp_configure_mst(struct intel_dp *intel_dp)
 {
+	bool was_mst;
+
 	if (!i915_modparams.enable_dp_mst)
 		return;
 
 	if (!intel_dp->can_mst)
 		return;
 
+	was_mst = intel_dp->is_mst;
 	intel_dp->is_mst = intel_dp_can_mst(intel_dp);
 
-	if (intel_dp->is_mst)
+	if (intel_dp->is_mst) {
 		DRM_DEBUG_KMS("Sink is MST capable\n");
-	else
+
+		if (!was_mst)
+			intel_dp->mst_bw_locked = false;
+	} else {
 		DRM_DEBUG_KMS("Sink is not MST capable\n");
+	}
 
 	drm_dp_mst_topology_mgr_set_mst(&intel_dp->mst_mgr,
 					intel_dp->is_mst);
diff --git a/drivers/gpu/drm/i915/intel_dp_mst.c b/drivers/gpu/drm/i915/intel_dp_mst.c
index c3de0918ee13..c0553456b18e 100644
--- a/drivers/gpu/drm/i915/intel_dp_mst.c
+++ b/drivers/gpu/drm/i915/intel_dp_mst.c
@@ -42,7 +42,7 @@ static bool intel_dp_mst_compute_config(struct intel_encoder *encoder,
 		to_intel_connector(conn_state->connector);
 	struct drm_atomic_state *state = pipe_config->base.state;
 	int bpp;
-	int lane_count, slots;
+	int lane_count, link_rate, slots;
 	const struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
 	int mst_pbn;
 	bool reduce_m_n = drm_dp_has_quirk(&intel_dp->desc,
@@ -56,16 +56,22 @@ static bool intel_dp_mst_compute_config(struct intel_encoder *encoder,
 			      bpp);
 	}
 	/*
-	 * for MST we always configure max link bw - the spec doesn't
-	 * seem to suggest we should do otherwise.
+	 * for MST we always configure max link bw if we don't know better -
+	 * the spec doesn't seem to suggest we should do otherwise. But,
+	 * ensure it always stays consistent with the rest of this hub's
+	 * state.
 	 */
-	lane_count = intel_dp_max_lane_count(intel_dp);
+	if (intel_dp->mst_bw_locked) {
+		lane_count = intel_dp->lane_count;
+		link_rate = intel_dp->link_rate;
+	} else {
+		lane_count = intel_dp_max_lane_count(intel_dp);
+		link_rate = intel_dp_max_link_rate(intel_dp);
+	}
 
 	pipe_config->lane_count = lane_count;
-
 	pipe_config->pipe_bpp = bpp;
-
-	pipe_config->port_clock = intel_dp_max_link_rate(intel_dp);
+	pipe_config->port_clock = link_rate;
 
 	if (drm_dp_mst_port_has_audio(&intel_dp->mst_mgr, connector->port))
 		pipe_config->has_audio = true;
@@ -221,6 +227,8 @@ static void intel_mst_pre_enable_dp(struct intel_encoder *encoder,
 	connector->encoder = encoder;
 	intel_mst->connector = connector;
 
+	intel_dp->mst_bw_locked = true;
+
 	DRM_DEBUG_KMS("active links %d\n", intel_dp->active_mst_links);
 
 	drm_dp_send_power_updown_phy(&intel_dp->mst_mgr, connector->port, true);
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index 3700fcfddb1f..e5d3ef6754a5 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -1110,6 +1110,12 @@ struct intel_dp {
 	bool can_mst; /* this port supports mst */
 	bool is_mst;
 	int active_mst_links;
+	/* Set when we've already decided on a link bw for mst, to prevent us
+	 * from setting different link bandwiths if the hub tries to confuse
+	 * us by changing it later
+	 */
+	bool mst_bw_locked;
+
 	/* connector directly attached - won't be use for modeset in mst world */
 	struct intel_connector *attached_connector;
 
-- 
2.14.3