[Intel-gfx] [PATCH 1/5] drm/i915: Enable edp psr error interrupts on hsw
Ville Syrjälä
ville.syrjala at linux.intel.com
Thu Mar 22 11:33:10 UTC 2018
On Thu, Mar 22, 2018 at 01:19:19AM +0000, Pandiyan, Dhinakaran wrote:
>
>
>
> On Wed, 2018-03-21 at 21:29 +0200, Ville Syrjälä wrote:
> > On Wed, Mar 21, 2018 at 07:19:53PM +0000, Pandiyan, Dhinakaran wrote:
> > >
> > >
> > >
> > > On Wed, 2018-03-21 at 20:59 +0200, Ville Syrjälä wrote:
> > > > On Tue, Mar 20, 2018 at 03:41:47PM -0700, Dhinakaran Pandiyan wrote:
> > > > > From: Daniel Vetter <daniel.vetter at ffwll.ch>
> > > > >
> > > > > The definitions for the error register should be valid on bdw/skl too,
> > > > > but there we haven't even enabled DE_MISC handling yet.
> > > > >
> > > > > Somewhat confusing the the moved register offset on bdw is only for
> > > > > the _CTL/_AUX register, and that _IIR/IMR stayed where they have been
> > > > > on bdw.
> > > > >
> > > > > v2: Fixes from Ville.
> > > > >
> > > > > v3: From DK
> > > > > * Rebased on drm-tip
> > > > > * Removed BDW IIR bit definition, looks like an unintentional change that
> > > > > should be in the following patch.
> > > > >
> > > > > Cc: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > > > > Cc: Rodrigo Vivi <rodrigo.vivi at intel.com>
> > > > > Cc: Daniel Vetter <daniel.vetter at intel.com>
> > > > > Signed-off-by: Daniel Vetter <daniel.vetter at intel.com>
> > > > > Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan at intel.com>
> > > > > ---
> > > > > drivers/gpu/drm/i915/i915_irq.c | 34 ++++++++++++++++++++++++++++++++++
> > > > > drivers/gpu/drm/i915/i915_reg.h | 8 ++++++++
> > > > > drivers/gpu/drm/i915/intel_psr.c | 3 ++-
> > > > > 3 files changed, 44 insertions(+), 1 deletion(-)
> > > > >
> > > > > diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
> > > > > index 44eef355e12c..e94a835b7515 100644
> > > > > --- a/drivers/gpu/drm/i915/i915_irq.c
> > > > > +++ b/drivers/gpu/drm/i915/i915_irq.c
> > > > > @@ -2392,6 +2392,26 @@ static void ilk_display_irq_handler(struct drm_i915_private *dev_priv,
> > > > > ironlake_rps_change_irq_handler(dev_priv);
> > > > > }
> > > > >
> > > > > +static void hsw_edp_psr_irq_handler(struct drm_i915_private *dev_priv)
> > > > > +{
> > > > > + u32 edp_psr_iir = I915_READ(EDP_PSR_IIR);
> > > > > +
> > > > > + if (edp_psr_iir & EDP_PSR_ERROR)
> > > > > + DRM_DEBUG_KMS("PSR error\n");
> > > > > +
> > > > > + if (edp_psr_iir & EDP_PSR_PRE_ENTRY) {
> > > > > + DRM_DEBUG_KMS("PSR prepare entry in 2 vblanks\n");
> > > >
> > > > I doubt we want to have the entry/exit interrupts generate all this
> > > > noise in dmesg all the time. We should probably only enable the
> > > > interrupts for testing. The error interrupt I suppose we want always,
> > > > might even want DRM_ERROR on it.
> > >
> > > I implement debugfs control in Patch 4/5, agreed on DRM_ERROR.
> >
> > Right. It's a bit hard to read this with stuff getting
> > added/remove/moved more or less randomly.
> >
> > >
> > > >
> > > > > + I915_WRITE(EDP_PSR_IMR, EDP_PSR_PRE_ENTRY);
> > > > > + }
> > > > > +
> > > > > + if (edp_psr_iir & EDP_PSR_POST_EXIT) {
> > > > > + DRM_DEBUG_KMS("PSR exit completed\n");
> > > > > + I915_WRITE(EDP_PSR_IMR, 0);
> > > > > + }
> > > > > +
> > > > > + I915_WRITE(EDP_PSR_IIR, edp_psr_iir);
> > > > > +}
> > > > > +
> > > > > static void ivb_display_irq_handler(struct drm_i915_private *dev_priv,
> > > > > u32 de_iir)
> > > > > {
> > > > > @@ -2404,6 +2424,9 @@ static void ivb_display_irq_handler(struct drm_i915_private *dev_priv,
> > > > > if (de_iir & DE_ERR_INT_IVB)
> > > > > ivb_err_int_handler(dev_priv);
> > > > >
> > > > > + if (de_iir & DE_EDP_PSR_INT_HSW)
> > > > > + hsw_edp_psr_irq_handler(dev_priv);
> > > > > +
> > > > > if (de_iir & DE_AUX_CHANNEL_A_IVB)
> > > > > dp_aux_irq_handler(dev_priv);
> > > > >
> > > > > @@ -3252,6 +3275,11 @@ static void ironlake_irq_reset(struct drm_device *dev)
> > > > > if (IS_GEN7(dev_priv))
> > > > > I915_WRITE(GEN7_ERR_INT, 0xffffffff);
> > > > >
> > > > > + if (IS_HASWELL(dev_priv)) {
> > > > > + I915_WRITE(EDP_PSR_IMR, 0xffffffff);
> > > > > + I915_WRITE(EDP_PSR_IIR, 0xffffffff);
> > > > > + }
> > > > > +
> > > > > gen5_gt_irq_reset(dev_priv);
> > > > >
> > > > > ibx_irq_reset(dev_priv);
> > > > > @@ -3663,6 +3691,12 @@ static int ironlake_irq_postinstall(struct drm_device *dev)
> > > > > DE_DP_A_HOTPLUG);
> > > > > }
> > > > >
> > > > > + if (IS_HASWELL(dev_priv)) {
> > > > > + gen3_assert_iir_is_zero(dev_priv, EDP_PSR_IIR);
> > > > > + I915_WRITE(EDP_PSR_IMR, 0);
> > > > > + display_mask |= DE_EDP_PSR_INT_HSW;
> > > > > + }
> > > > > +
> > > > > dev_priv->irq_mask = ~display_mask;
> > > > >
> > > > > ibx_irq_pre_postinstall(dev);
> > > > > diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> > > > > index 1e000f3004cb..3447f03eac3d 100644
> > > > > --- a/drivers/gpu/drm/i915/i915_reg.h
> > > > > +++ b/drivers/gpu/drm/i915/i915_reg.h
> > > > > @@ -3828,6 +3828,13 @@ enum {
> > > > > #define EDP_PSR_TP1_TIME_0us (3<<4)
> > > > > #define EDP_PSR_IDLE_FRAME_SHIFT 0
> > > > >
> > > > > +/* Bspec claims those aren't shifted but stay at 0x64800 */
> > > > > +#define EDP_PSR_IMR _MMIO(0x64834)
> > > > > +#define EDP_PSR_IIR _MMIO(0x64838)
> > > > > +#define EDP_PSR_ERROR (1<<2)
> > > > > +#define EDP_PSR_POST_EXIT (1<<1)
> > > > > +#define EDP_PSR_PRE_ENTRY (1<<0)
> > > > > +
> > > > > #define EDP_PSR_AUX_CTL _MMIO(dev_priv->psr_mmio_base + 0x10)
> > > > > #define EDP_PSR_AUX_DATA(i) _MMIO(dev_priv->psr_mmio_base + 0x14 + (i) * 4) /* 5 registers */
> > > > >
> > > > > @@ -6628,6 +6635,7 @@ enum {
> > > > > #define DE_PCH_EVENT_IVB (1<<28)
> > > > > #define DE_DP_A_HOTPLUG_IVB (1<<27)
> > > > > #define DE_AUX_CHANNEL_A_IVB (1<<26)
> > > > > +#define DE_EDP_PSR_INT_HSW (1<<19)
> > > > > #define DE_SPRITEC_FLIP_DONE_IVB (1<<14)
> > > > > #define DE_PLANEC_FLIP_DONE_IVB (1<<13)
> > > > > #define DE_PIPEC_VBLANK_IVB (1<<10)
> > > > > diff --git a/drivers/gpu/drm/i915/intel_psr.c b/drivers/gpu/drm/i915/intel_psr.c
> > > > > index 317cb4a12693..27dfd507a4f7 100644
> > > > > --- a/drivers/gpu/drm/i915/intel_psr.c
> > > > > +++ b/drivers/gpu/drm/i915/intel_psr.c
> > > > > @@ -613,7 +613,8 @@ static void hsw_psr_enable_source(struct intel_dp *intel_dp,
> > > > > I915_WRITE(EDP_PSR_DEBUG,
> > > > > EDP_PSR_DEBUG_MASK_MEMUP |
> > > > > EDP_PSR_DEBUG_MASK_HPD |
> > > > > - EDP_PSR_DEBUG_MASK_LPSP);
> > > > > + EDP_PSR_DEBUG_MASK_LPSP |
> > > > > + EDP_PSR_DEBUG_MASK_REG_WRITE);
> > > >
> > > > I don't think Daniel's original had this actually. I think I added it
> > > > because I didn't want mmio to mess up my testing.
> > >
> > > It gets removed in a separate patch (2/5). So I assumed Daniel added it
> > > and you removed it.
> >
> > Hmm. That could indeed be the case.
> >
> > >
> > >
> > > > In general I'd really
> > > > prefer to mask everything so that we can be sure that the PSR exits
> > > > happen when we want/need them and not randomly due to other activity.
> > > >
> > > > If any random mmio can cause a PSR exit it's going to hard to prove that
> > > > we're doing the correct thing. Also seems pretty wasteful if eg. GT
> > > > interrupts can cause PSR exits for no good reason. I never tested to see
> > > > which registers cause the PSR exit. That would be good to know.
> > > >
> > >
> > > The same bit on SKL+ is called "Mask Display Reg Write", so it either
> > > means
> > > 1) HSW and BDW exit only on display register writes and the bspec
> > > description is ambiguous or
> >
> > The problem is that eg. some of the interrupt registers live in the
> > display block. Hence any interrupt could potentially cause the PSR exit.
> > As could any register read we do for debug purpose etc. So at least I
> > would feel safer if PSR can be made to work reliably with more or less
> > everything masked.
> >
> The idea is to move towards hardware triggered exits since that's what
> is necessary for PSR2 selective updates[1]. More importantly, there are
> places in the driver where we can't manually exit PSR without
> circumventing locking issues - from vblank enable for instance. Relying
> on hardware triggered exits in the modeset/commit path keeps it
> consistent IMO.
What's the difference between the hardware behaviour between "write any
random mmio to trigger an exit" vs. "write some specific register to
trigger an exit". I presume there is a way to trigger the exit
explicitly?
--
Ville Syrjälä
Intel OTC
More information about the Intel-gfx
mailing list