[Intel-gfx] [PATCH 08/17] drm/i915/icl: Implement voltage swing programming sequence for Combo PHY DDI
Paulo Zanoni
paulo.r.zanoni at intel.com
Thu Mar 22 22:23:44 UTC 2018
Em Qui, 2018-02-22 às 00:55 -0300, Paulo Zanoni escreveu:
> From: Manasi Navare <manasi.d.navare at intel.com>
>
> This is an important part of the DDI initalization as well as
> for changing the voltage during DisplayPort link training.
>
> The Voltage swing seqeuence is similar to Cannonlake.
> However it has different register definitions and hence
> it makes sense to create a separate vswing sequence and
> program functions for ICL to leave room for more changes
> in case the Bspec changes later and deviates from CNL sequence.
>
> v2:
> Use ~TAP3_DISABLE for enbaling that bit (Jani Nikula)
>
> v3:
> * Use dw4_scaling column for PORT_TX_DW4 values (Rodrigo)
>
> v4:
> * Call it combo_vswing, use switch statement (Paulo)
>
> v5 (from Paulo):
> * Fix a typo.
> * s/rate < 600000/rate <= 600000/.
> * Don't remove blank lines that should be there.
>
> v6:
> * Rebased by Rodrigo on top of Cannonlake changes
> where non vswing sequences are not aligned with iboost
> anymore.
>
> v7: Another rebase after an upstream rework.
>
> v8 (from Paulo):
> * Adjust the code to the upstream output type changes.
> * Squash the patch that moved some functions up.
> * Merge both get_combo_buf_trans functions in order to simplify the
> code.
> * Change the changelog format.
>
> Cc: Jani Nikula <jani.nikula at linux.intel.com>
> Reviewed-by: Paulo Zanoni <paulo.r.zanoni at intel.com> (v5)
> Signed-off-by: Manasi Navare <manasi.d.navare at intel.com>
> Signed-off-by: Rodrigo Vivi <rodrigo.vivi at intel.com>
> Signed-off-by: Paulo Zanoni <paulo.r.zanoni at intel.com>
> ---
> drivers/gpu/drm/i915/intel_ddi.c | 189
> ++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 186 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_ddi.c
> b/drivers/gpu/drm/i915/intel_ddi.c
> index 0a4683991ec2..c38873cb98ca 100644
> --- a/drivers/gpu/drm/i915/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/intel_ddi.c
> @@ -849,6 +849,45 @@ cnl_get_buf_trans_edp(struct drm_i915_private
> *dev_priv, int *n_entries)
> }
> }
>
> +static const struct icl_combo_phy_ddi_buf_trans *
> +icl_get_combo_buf_trans(struct drm_i915_private *dev_priv, enum port
> port,
> + int type, int *n_entries)
> +{
> + u32 voltage = I915_READ(ICL_PORT_COMP_DW3(port)) &
> VOLTAGE_INFO_MASK;
> +
> + if (type == INTEL_OUTPUT_EDP && dev_priv-
> >vbt.edp.low_vswing) {
> + switch (voltage) {
> + case VOLTAGE_INFO_0_85V:
> + *n_entries =
> ARRAY_SIZE(icl_combo_phy_ddi_translations_edp_0_85V);
> + return
> icl_combo_phy_ddi_translations_edp_0_85V;
> + case VOLTAGE_INFO_0_95V:
> + *n_entries =
> ARRAY_SIZE(icl_combo_phy_ddi_translations_edp_0_95V);
> + return
> icl_combo_phy_ddi_translations_edp_0_95V;
> + case VOLTAGE_INFO_1_05V:
> + *n_entries =
> ARRAY_SIZE(icl_combo_phy_ddi_translations_edp_1_05V);
> + return
> icl_combo_phy_ddi_translations_edp_1_05V;
> + default:
> + MISSING_CASE(voltage);
> + return NULL;
> + }
> + } else {
> + switch (voltage) {
> + case VOLTAGE_INFO_0_85V:
> + *n_entries =
> ARRAY_SIZE(icl_combo_phy_ddi_translations_dp_hdmi_0_85V);
> + return
> icl_combo_phy_ddi_translations_dp_hdmi_0_85V;
> + case VOLTAGE_INFO_0_95V:
> + *n_entries =
> ARRAY_SIZE(icl_combo_phy_ddi_translations_dp_hdmi_0_95V);
> + return
> icl_combo_phy_ddi_translations_dp_hdmi_0_95V;
> + case VOLTAGE_INFO_1_05V:
> + *n_entries =
> ARRAY_SIZE(icl_combo_phy_ddi_translations_dp_hdmi_1_05V);
> + return
> icl_combo_phy_ddi_translations_dp_hdmi_1_05V;
> + default:
> + MISSING_CASE(voltage);
> + return NULL;
> + }
> + }
> +}
> +
> static int intel_ddi_hdmi_level(struct drm_i915_private *dev_priv,
> enum port port)
> {
> int n_entries, level, default_entry;
> @@ -2178,6 +2217,144 @@ static void cnl_ddi_vswing_sequence(struct
> intel_encoder *encoder,
> I915_WRITE(CNL_PORT_TX_DW5_GRP(port), val);
> }
>
> +static void icl_ddi_combo_vswing_program(struct drm_i915_private
> *dev_priv,
> + u32 level, enum port port,
> int type)
> +{
> + const struct icl_combo_phy_ddi_buf_trans *ddi_translations =
> NULL;
> + u32 n_entries, val;
> + int ln;
> +
> + ddi_translations = icl_get_combo_buf_trans(dev_priv, port,
> type,
> + &n_entries);
> + if (!ddi_translations)
> + return;
> +
> + if (level >= n_entries) {
> + DRM_DEBUG_KMS("DDI translation not found for level
> %d. Using %d instead.", level, n_entries - 1);
> + level = n_entries - 1;
> + }
> +
> + /* Set PORT_TX_DW5 Scaling Mode Sel to 110b. */
> + val = I915_READ(ICL_PORT_TX_DW5_LN0(port));
> + val &= ~SCALING_MODE_SEL_MASK;
> + val |= SCALING_MODE_SEL(0x6);
This should be RTERM_SEL.
> + I915_WRITE(ICL_PORT_TX_DW5_GRP(port), val);
> +
> + /* Program PORT_TX_DW5 */
> + val = I915_READ(ICL_PORT_TX_DW5_LN0(port));
> + /* Set DisableTap2 and DisableTap3 if MIPI DSI
> + * Clear DisableTap2 and DisableTap3 for all other Ports
> + */
> + if (type == INTEL_OUTPUT_DSI) {
> + val |= TAP2_DISABLE;
> + val |= TAP3_DISABLE;
> + } else {
> + val &= ~TAP2_DISABLE;
> + val &= ~TAP3_DISABLE;
> + }
> + I915_WRITE(ICL_PORT_TX_DW5_GRP(port), val);
> +
> + /* Program PORT_TX_DW2 */
> + val = I915_READ(ICL_PORT_TX_DW2_LN0(port));
> + val &= ~(SWING_SEL_LOWER_MASK | SWING_SEL_UPPER_MASK |
> + RCOMP_SCALAR_MASK);
> + val |=
> SWING_SEL_UPPER(ddi_translations[level].dw2_swing_select);
> + val |=
> SWING_SEL_LOWER(ddi_translations[level].dw2_swing_select);
> + /* Program Rcomp scalar for every table entry */
> + val |=
> RCOMP_SCALAR(ddi_translations[level].dw2_swing_scalar);
> + I915_WRITE(ICL_PORT_TX_DW2_GRP(port), val);
> +
> + /* Program PORT_TX_DW4 */
> + /* We cannot write to GRP. It would overwrite individual
> loadgen. */
> + for (ln = 0; ln <= 3; ln++) {
> + val = I915_READ(ICL_PORT_TX_DW4_LN(port, ln));
> + val &= ~(POST_CURSOR_1_MASK | POST_CURSOR_2_MASK |
> + CURSOR_COEFF_MASK);
> + val |= ddi_translations[level].dw4_scaling;
> + I915_WRITE(ICL_PORT_TX_DW4_LN(port, ln), val);
> + }
> +}
> +
> +static void icl_combo_phy_ddi_vswing_sequence(struct intel_encoder
> *encoder, u32 level)
> +{
> + struct drm_i915_private *dev_priv = to_i915(encoder-
> >base.dev);
> + enum port port = encoder->port;
> + int type = encoder->type;
> + int width = 0;
> + int rate = 0;
> + u32 val;
> + int ln = 0;
> +
> + if (type == INTEL_OUTPUT_HDMI) {
> + width = 4;
> + /* Rate is always < than 6GHz for HDMI */
> + } else {
> + struct intel_dp *intel_dp =
> enc_to_intel_dp(&encoder->base);
> +
> + width = intel_dp->lane_count;
> + rate = intel_dp->link_rate;
> + }
> +
> + /*
> + * 1. If port type is eDP or DP,
> + * set PORT_PCS_DW1 cmnkeeper_enable to 1b,
> + * else clear to 0b.
> + */
> + val = I915_READ(ICL_PORT_PCS_DW1_LN0(port));
> + if (type == INTEL_OUTPUT_HDMI)
> + val &= ~COMMON_KEEPER_EN;
> + else
> + val |= COMMON_KEEPER_EN;
> + I915_WRITE(ICL_PORT_PCS_DW1_GRP(port), val);
> +
> + /* 2. Program loadgen select */
> + /*
> + * Program PORT_TX_DW4_LN depending on Bit rate and used
> lanes
> + * <= 6 GHz and 4 lanes (LN0=0, LN1=1, LN2=1, LN3=1)
> + * <= 6 GHz and 1,2 lanes (LN0=0, LN1=1, LN2=1, LN3=0)
> + * > 6 GHz (LN0=0, LN1=0, LN2=0, LN3=0)
> + */
> + for (ln = 0; ln <= 3; ln++) {
> + val = I915_READ(ICL_PORT_TX_DW4_LN(port, ln));
> + val &= ~LOADGEN_SELECT;
> +
> + if ((rate <= 600000 && width == 4 && ln >= 1) ||
> + (rate <= 600000 && width < 4 && (ln == 1 || ln
> == 2))) {
> + val |= LOADGEN_SELECT;
> + }
> + I915_WRITE(ICL_PORT_TX_DW4_LN(port, ln), val);
> + }
> +
> + /* 3. Set PORT_CL_DW5 SUS Clock Config to 11b */
> + val = I915_READ(ICL_PORT_CL_DW5(port));
> + val |= SUS_CLOCK_CONFIG;
> + I915_WRITE(ICL_PORT_CL_DW5(port), val);
> +
> + /* 4. Clear training enable to change swing values */
> + val = I915_READ(ICL_PORT_TX_DW5_LN0(port));
> + val &= ~TX_TRAINING_EN;
> + I915_WRITE(ICL_PORT_TX_DW5_GRP(port), val);
> +
> + /* 5. Program swing and de-emphasis */
> + icl_ddi_combo_vswing_program(dev_priv, level, port, type);
> +
> + /* 6. Set training enable to trigger update */
> + val = I915_READ(ICL_PORT_TX_DW5_LN0(port));
> + val |= TX_TRAINING_EN;
> + I915_WRITE(ICL_PORT_TX_DW5_GRP(port), val);
> +}
> +
> +static void icl_ddi_vswing_sequence(struct intel_encoder *encoder,
> u32 level)
> +{
> + enum port port = encoder->port;
> +
> + if (port == PORT_A || port == PORT_B)
> + icl_combo_phy_ddi_vswing_sequence(encoder, level);
> + else
> + /* Not Implemented Yet */
> + WARN_ON(1);
> +}
> +
> static uint32_t translate_signal_level(int signal_levels)
> {
> int i;
> @@ -2209,7 +2386,9 @@ u32 bxt_signal_levels(struct intel_dp
> *intel_dp)
> struct intel_encoder *encoder = &dport->base;
> int level = intel_ddi_dp_level(intel_dp);
>
> - if (IS_CANNONLAKE(dev_priv))
> + if (IS_ICELAKE(dev_priv))
> + icl_ddi_vswing_sequence(encoder, level);
I was 100% sure I had already reworked the patch to follow the new
standard for the other platforms, but I guess I was wrong.
I'll update this patch based on my review, but I guess now we'll be at
a point where I changed the patch so much that we'll need a new
reviewer.
> + else if (IS_CANNONLAKE(dev_priv))
> cnl_ddi_vswing_sequence(encoder, level, encoder-
> >type);
> else
> bxt_ddi_vswing_sequence(encoder, level, encoder-
> >type);
> @@ -2389,7 +2568,9 @@ static void intel_ddi_pre_enable_dp(struct
> intel_encoder *encoder,
>
> intel_display_power_get(dev_priv, dig_port-
> >ddi_io_power_domain);
>
> - if (IS_CANNONLAKE(dev_priv))
> + if (IS_ICELAKE(dev_priv))
> + icl_ddi_vswing_sequence(encoder, level);
> + else if (IS_CANNONLAKE(dev_priv))
> cnl_ddi_vswing_sequence(encoder, level, encoder-
> >type);
> else if (IS_GEN9_LP(dev_priv))
> bxt_ddi_vswing_sequence(encoder, level, encoder-
> >type);
> @@ -2420,7 +2601,9 @@ static void intel_ddi_pre_enable_hdmi(struct
> intel_encoder *encoder,
>
> intel_display_power_get(dev_priv, dig_port-
> >ddi_io_power_domain);
>
> - if (IS_CANNONLAKE(dev_priv))
> + if (IS_ICELAKE(dev_priv))
> + icl_ddi_vswing_sequence(encoder, level);
> + else if (IS_CANNONLAKE(dev_priv))
> cnl_ddi_vswing_sequence(encoder, level,
> INTEL_OUTPUT_HDMI);
> else if (IS_GEN9_LP(dev_priv))
> bxt_ddi_vswing_sequence(encoder, level,
> INTEL_OUTPUT_HDMI);
More information about the Intel-gfx
mailing list