[Intel-gfx] [PATCH v5 24/28] drm/i915/dp: Configure Display stream splitter registers during DSC enable

[Manasi Navare]

On Thu, Oct 18, 2018 at 08:02:14PM +0300, Ville Syrjälä wrote:
> On Fri, Oct 05, 2018 at 04:23:02PM -0700, Manasi Navare wrote:
> > Display Stream Splitter registers need to be programmed to enable
> > the joiner if two DSC engines are used and also to enable
> > the left and the right DSC engines. This happens as part of
> > the DSC enabling routine in the source in atomic commit.
> > 
> > v2:
> > * Rebase (Manasi)
> > 
> > Cc: Jani Nikula <jani.nikula at linux.intel.com>
> > Cc: Ville Syrjala <ville.syrjala at linux.intel.com>
> > Cc: Anusha Srivatsa <anusha.srivatsa at intel.com>
> > Signed-off-by: Manasi Navare <manasi.d.navare at intel.com>
> > Reviewed-by: Anusha Srivatsa <anusha.srivatsa at intelcom>
> > ---
> >  drivers/gpu/drm/i915/intel_vdsc.c | 22 ++++++++++++++++++++++
> >  1 file changed, 22 insertions(+)
> > 
> > diff --git a/drivers/gpu/drm/i915/intel_vdsc.c b/drivers/gpu/drm/i915/intel_vdsc.c
> > index f2b3b30b6f5e..d3001647a887 100644
> > --- a/drivers/gpu/drm/i915/intel_vdsc.c
> > +++ b/drivers/gpu/drm/i915/intel_vdsc.c
> > @@ -1009,6 +1009,12 @@ static void intel_dp_send_dsc_pps_sdp(struct intel_encoder *encoder,
> >  void intel_dsc_enable(struct intel_encoder *encoder,
> >  		      struct intel_crtc_state *crtc_state)
> >  {
> > +	struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
> > +	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> > +	enum pipe pipe = crtc->pipe;
> > +	i915_reg_t dss_ctl1_reg, dss_ctl2_reg;
> > +	u32 dss_ctl1_val = 0;
> > +	u32 dss_ctl2_val = 0;
> >  
> >  	if (!crtc_state->dsc_params.compression_enable)
> >  		return;
> > @@ -1017,5 +1023,21 @@ void intel_dsc_enable(struct intel_encoder *encoder,
> >  
> >  	intel_dp_send_dsc_pps_sdp(encoder, crtc_state);
> >  
> > +	/* Configure DSS_CTL registers for DSC */
> > +	if (encoder->type == INTEL_OUTPUT_EDP) {
> 
> Presumably this should check the transcoder instead? I see a lot of
> similar confusion in other patches as well.
>

So that would mean that if we force eDP output on pipe B then it will use transcoder B
and hence DSC engines on transcoder B, so we would use the DSS_CTL1/2 only for
Transcoder EDP else it shd use ICL_PIPE_DSS_CTL1(pipe).

And same for the DSC PPS configure patch as well.

Correct?
 
> > +		dss_ctl1_reg = DSS_CTL1;
> > +		dss_ctl2_reg = DSS_CTL2;
> > +	} else {
> > +		dss_ctl1_reg = ICL_PIPE_DSS_CTL1(pipe);
> > +		dss_ctl2_reg = ICL_PIPE_DSS_CTL2(pipe);
> > +	}
> > +	dss_ctl2_val |= LEFT_BRANCH_VDSC_ENABLE;
> > +	if (crtc_state->dsc_params.dsc_split) {
> > +		dss_ctl2_val |= RIGHT_BRANCH_VDSC_ENABLE;
> > +		dss_ctl1_val |= JOINER_ENABLE;
> > +	}
> > +	I915_WRITE(dss_ctl1_reg, dss_ctl1_val);
> > +	I915_WRITE(dss_ctl2_reg, dss_ctl2_val);
> > +
> >  	return;
> >  }
> > -- 
> > 2.18.0
> 
> -- 
> Ville Syrjälä
> Intel