[Intel-gfx] [PATCH v10 1/6] drm/i915/tgl: Add DC3CO required register and bits

[Anshuman Gupta]

On 2019-10-04 at 18:48:08 +0300, Ville Syrjälä wrote:
> On Thu, Oct 03, 2019 at 01:47:33PM +0530, Anshuman Gupta wrote:
> > Adding following definition to i915_reg.h
> > 1. DC_STATE_EN register DC3CO bit fields and masks.
> >    DC3CO enable bit will be used by driver to make DC3CO
> >    ready for DMC f/w and status bit will be used as DC3CO
> >    entry status.
> > 2. Transcoder EXITLINE register and its bit fields and mask.
> >    Transcoder EXITLINE enable bit represents PSR2 idle frame
> >    reset should be applied at exit line and exitlines mask
> >    represent required number of scanlines at which DC3CO
> >    exit happens.
> > 
> >    B.Specs:49196
> > 
> > v1: Use of REG_BIT and using extra space for EXITLINE_ macro
> >     definition. [Animesh]
> > 
> > Cc: Jani Nikula <jani.nikula at intel.com>
> > Cc: Imre Deak <imre.deak at intel.com>
> > Cc: Animesh Manna <animesh.manna at intel.com>
> > Reviewed-by: Animesh Manna <animesh.manna at intel.com>
> > Reviewed-by: Imre Deak <imre.deak at intel.com>
> > Signed-off-by: Anshuman Gupta <anshuman.gupta at intel.com>
> > ---
> >  drivers/gpu/drm/i915/i915_reg.h | 8 ++++++++
> >  1 file changed, 8 insertions(+)
> > 
> > diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> > index eefd789b9a28..8fd93008214b 100644
> > --- a/drivers/gpu/drm/i915/i915_reg.h
> > +++ b/drivers/gpu/drm/i915/i915_reg.h
> > @@ -4144,6 +4144,7 @@ enum {
> >  #define _VTOTAL_A	0x6000c
> >  #define _VBLANK_A	0x60010
> >  #define _VSYNC_A	0x60014
> > +#define _EXITLINE_A	0x60018
> >  #define _PIPEASRC	0x6001c
> >  #define _BCLRPAT_A	0x60020
> >  #define _VSYNCSHIFT_A	0x60028
> > @@ -4190,11 +4191,16 @@ enum {
> >  #define VTOTAL(trans)		_MMIO_TRANS2(trans, _VTOTAL_A)
> >  #define VBLANK(trans)		_MMIO_TRANS2(trans, _VBLANK_A)
> >  #define VSYNC(trans)		_MMIO_TRANS2(trans, _VSYNC_A)
> > +#define EXITLINE(trans)		_MMIO_TRANS2(trans, _EXITLINE_A)
> >  #define BCLRPAT(trans)		_MMIO_TRANS2(trans, _BCLRPAT_A)
> >  #define VSYNCSHIFT(trans)	_MMIO_TRANS2(trans, _VSYNCSHIFT_A)
> >  #define PIPESRC(trans)		_MMIO_TRANS2(trans, _PIPEASRC)
> >  #define PIPE_MULT(trans)	_MMIO_TRANS2(trans, _PIPE_MULT_A)
> >  
> > +#define   EXITLINE_ENABLE	REG_BIT(31)
> > +#define   EXITLINE_MASK		REG_GENMASK(12, 0)
> > +#define   EXITLINE_SHIFT	0
> 
> Why are these defines hanging mid-air?
If i understand your comment correctly, the place these EXITLINE
bit defines is not correct, and it should be moved after
EXITLINE(trans) define, am i correct ? 
> 
> > +
> >  /*
> >   * HSW+ eDP PSR registers
> >   *
> > @@ -10288,6 +10294,8 @@ enum skl_power_gate {
> >  /* GEN9 DC */
> >  #define DC_STATE_EN			_MMIO(0x45504)
> >  #define  DC_STATE_DISABLE		0
> > +#define  DC_STATE_EN_DC3CO		REG_BIT(30)
> > +#define  DC_STATE_DC3CO_STATUS		REG_BIT(29)
> >  #define  DC_STATE_EN_UPTO_DC5		(1 << 0)
> >  #define  DC_STATE_EN_DC9		(1 << 3)
> >  #define  DC_STATE_EN_UPTO_DC6		(2 << 0)
> > -- 
> > 2.21.0
> > 
> > _______________________________________________
> > Intel-gfx mailing list
> > Intel-gfx at lists.freedesktop.org
> > https://lists.freedesktop.org/mailman/listinfo/intel-gfx
> 
> -- 
> Ville Syrjälä
> Intel