Unexpected Mode Preference when using --nas-set-system-selection-preference
Garrett Doorenbos
gdoorenbos at yahoo.com
Tue Apr 14 12:50:44 PDT 2015
Markus, I somehow missed your most recent email when I sent my last reply. I tried the set command as well, but I got a 'unknown option' error. I'm guessing that's due to using the older version?
On Tuesday, April 14, 2015 2:47 PM, Garrett Doorenbos <gdoorenbos at yahoo.com> wrote:
Thanks everyone for the helpful information.
Markus, I get a 'InvalidQmiCommand' error when I try to use that command. I'm also trying to set the technology preference. Is there an alternative to --nas-set-system-selection-prefrence for that?
I haven't tried updating the libqmi version yet, but I hope to soon.
Thanks,Garrett
On Tuesday, April 14, 2015 2:36 PM, Markus Gothe <nietzsche at lysator.liu.se> wrote:
Try using ‘--nas-get-technology-preference’ instead. It might work better.
//M
On 13 Apr 2015, at 22:43 , Markus Gothe <nietzsche at lysator.liu.se> wrote:
> There is something wrong with your modem... Sorry to say. The Verizon USB551L doesnt support neither GSM nor UMTS. :-(
> There are two known ways to get/set rat...
>
> The NAS set selection preference methinks is be uses when to choose between CDMA and GSM.
>
> I will check this up when I have the source code at hand.
>
> //M
>
> Den 10 apr 2015 22:10 skrev Garrett Doorenbos <gdoorenbos at yahoo.com>:
>>
>> Hello,
>>
>> I am using qmicli with a Novatel USB551L modem. When I try to use the --nas-set-system-selection-preference command to set my preference to ‘lte’, I get a ‘DeviceUnsupported’ error. I noticed that if I run the command with the verbose tag, the Mode Preference sent to the modem is ‘gsm, lte, td-scdma’. I think this causes problems since my modem doesn’t support td-scdma (--dms-get-capabilities shows only cdma20001x, evdo, gsm, umts, lte). I also noticed that whatever input I give to --nas-set-system-selection-preference, it seems to OR it with gsm, lte, and td-scdma. Is there a way to get --nas-set-system-selection-preference to only send ‘lte’ for the Mode Preference? I’ve copy/pasted results from my machine below.
>>
>> Thanks,
>> Garrett
>>
>> -----
>>
>> sh-4.2# qmicli -d /dev/cdc-wdm0 --dms-get-capabilities
>> [/dev/cdc-wdm0] Device capabilities retrieved:
>> Max TX channel rate: '5742000'
>> Max RX channel rate: '7200000'
>> Data Service: 'simultaneous-cs-ps'
>> SIM: 'supported'
>> Networks: 'cdma20001x, evdo, gsm, umts, lte'
>> sh-4.2# qmicli -d /dev/cdc-wdm0 --nas-set-system-selection-preference=lte
>> error: couldn't set operating mode: QMI protocol error (25): 'DeviceUnsupported'
>> sh-4.2# qmicli -d /dev/cdc-wdm0 --nas-set-system-selection-preference=lte -v
>> [13 Sep 2000, 03:43:25] [Debug] QMI Device at '/dev/cdc-wdm0' ready
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Assuming service 'nas' is supported...
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Allocating new client ID...
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Sent message...
>> <<<<<< RAW:
>> <<<<<< length = 16
>> <<<<<< data = 01:0F:00:00:00:00:00:01:22:00:04:00:01:01:00:03
>>
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Sent message (translated)...
>> <<<<<< QMUX:
>> <<<<<< length = 15
>> <<<<<< flags = 0x00
>> <<<<<< service = "ctl"
>> <<<<<< client = 0
>> <<<<<< QMI:
>> <<<<<< flags = "none"
>> <<<<<< transaction = 1
>> <<<<<< tlv_length = 4
>> <<<<<< message = "Allocate CID" (0x0022)
>> <<<<<< TLV:
>> <<<<<< type = "Service" (0x01)
>> <<<<<< length = 1
>> <<<<<< value = 03
>> <<<<<< translated = nas
>>
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Received message...
>>>>>>>> RAW:
>>>>>>>> length = 24
>>>>>>>> data = 01:17:00:80:00:00:01:01:22:00:0C:00:02:04:00:00:00:00:00:01:02:00:03:0A
>>
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Received message (translated)...
>>>>>>>> QMUX:
>>>>>>>> length = 23
>>>>>>>> flags = 0x80
>>>>>>>> service = "ctl"
>>>>>>>> client = 0
>>>>>>>> QMI:
>>>>>>>> flags = "response"
>>>>>>>> transaction = 1
>>>>>>>> tlv_length = 12
>>>>>>>> message = "Allocate CID" (0x0022)
>>>>>>>> TLV:
>>>>>>>> type = "Result" (0x02)
>>>>>>>> length = 4
>>>>>>>> value = 00:00:00:00
>>>>>>>> translated = SUCCESS
>>>>>>>> TLV:
>>>>>>>> type = "Allocation Info" (0x01)
>>>>>>>> length = 2
>>>>>>>> value = 03:0A
>>>>>>>> translated = [ service = 'nas' cid = '10' ]
>>
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Registered 'nas' (version unknown) client with ID '10'
>> [13 Sep 2000, 03:43:25] [Debug] Asynchronously setting system selection preference...
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Sent message...
>> <<<<<< RAW:
>> <<<<<< length = 29
>> <<<<<< data = 01:1C:00:00:03:0A:00:01:00:33:00:10:00:19:04:00:00:00:00:00:17:01:00:01:11:02:00:B4:5B
>>
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Sent message (translated)...
>> <<<<<< QMUX:
>> <<<<<< length = 28
>> <<<<<< flags = 0x00
>> <<<<<< service = "nas"
>> <<<<<< client = 10
>> <<<<<< QMI:
>> <<<<<< flags = "none"
>> <<<<<< transaction = 1
>> <<<<<< tlv_length = 16
>> <<<<<< message = "Set System Selection Preference" (0x0033)
>> <<<<<< TLV:
>> <<<<<< type = "GSM WCDMA Acquisition Order Preference" (0x19)
>> <<<<<< length = 4
>> <<<<<< value = 00:00:00:00
>> <<<<<< translated = automatic
>> <<<<<< TLV:
>> <<<<<< type = "Change Duration" (0x17)
>> <<<<<< length = 1
>> <<<<<< value = 01
>> <<<<<< translated = permanent
>> <<<<<< TLV:
>> <<<<<< type = "Mode Preference" (0x11)
>> <<<<<< length = 2
>> <<<<<< value = B4:5B
>> <<<<<< translated = gsm, lte, td-scdma
>>
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Received message...
>>>>>>>> RAW:
>>>>>>>> length = 20
>>>>>>>> data = 01:13:00:80:03:0A:02:01:00:33:00:07:00:02:04:00:01:00:19:00
>>
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Received message (translated)...
>>>>>>>> QMUX:
>>>>>>>> length = 19
>>>>>>>> flags = 0x80
>>>>>>>> service = "nas"
>>>>>>>> client = 10
>>>>>>>> QMI:
>>>>>>>> flags = "response"
>>>>>>>> transaction = 1
>>>>>>>> tlv_length = 7
>>>>>>>> message = "Set System Selection Preference" (0x0033)
>>>>>>>> TLV:
>>>>>>>> type = "Result" (0x02)
>>>>>>>> length = 4
>>>>>>>> value = 01:00:19:00
>>>>>>>> translated = FAILURE: DeviceUnsupported
>>
>> error: couldn't set operating mode: QMI protocol error (25): 'DeviceUnsupported'
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Unregistered 'nas' client with ID '10'
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Sent message...
>> <<<<<< RAW:
>> <<<<<< length = 17
>> <<<<<< data = 01:10:00:00:00:00:00:02:23:00:05:00:01:02:00:03:0A
>>
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Sent message (translated)...
>> <<<<<< QMUX:
>> <<<<<< length = 16
>> <<<<<< flags = 0x00
>> <<<<<< service = "ctl"
>> <<<<<< client = 0
>> <<<<<< QMI:
>> <<<<<< flags = "none"
>> <<<<<< transaction = 2
>> <<<<<< tlv_length = 5
>> <<<<<< message = "Release CID" (0x0023)
>> <<<<<< TLV:
>> <<<<<< type = "Release Info" (0x01)
>> <<<<<< length = 2
>> <<<<<< value = 03:0A
>> <<<<<< translated = [ service = 'nas' cid = '10' ]
>>
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Received message...
>>>>>>>> RAW:
>>>>>>>> length = 24
>>>>>>>> data = 01:17:00:80:00:00:01:02:23:00:0C:00:02:04:00:00:00:00:00:01:02:00:03:0A
>>
>> [13 Sep 2000, 03:43:25] [Debug] [/dev/cdc-wdm0] Received message (translated)...
>>>>>>>> QMUX:
>>>>>>>> length = 23
>>>>>>>> flags = 0x80
>>>>>>>> service = "ctl"
>>>>>>>> client = 0
>>>>>>>> QMI:
>>>>>>>> flags = "response"
>>>>>>>> transaction = 2
>>>>>>>> tlv_length = 12
>>>>>>>> message = "Release CID" (0x0023)
>>>>>>>> TLV:
>>>>>>>> type = "Result" (0x02)
>>>>>>>> length = 4
>>>>>>>> value = 00:00:00:00
>>>>>>>> translated = SUCCESS
>>>>>>>> TLV:
>>>>>>>> type = "Release Info" (0x01)
>>>>>>>> length = 2
>>>>>>>> value = 03:0A
>>>>>>>> translated = [ service = 'nas' cid = '10' ]
>>
>> [13 Sep 2000, 03:43:25] [Debug] Client released
>> sh-4.2#
>>
> _______________________________________________
> libqmi-devel mailing list
> libqmi-devel at lists.freedesktop.org
> http://lists.freedesktop.org/mailman/listinfo/libqmi-devel
//Markus - The panama-hat hacker
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.freedesktop.org/archives/libqmi-devel/attachments/20150414/2a5f2cfc/attachment-0001.html>
More information about the libqmi-devel
mailing list