QMI protocol error (26): 'NoEffect' on stopping

[Kavula Suresh]

Please help on this, I am facing with this error lot of issues. Whenever
signal drops, only way I can recover is from system complete boot.

Appreciate for your help.

Thanks,

On Thu, Aug 13, 2015 at 10:11 AM, Kavula Suresh <kavulas at gmail.com> wrote:

> Can you please help with these issues, please...
>
> After identified as Disconnected from status command - While stopping
> network:
>
> *Issue # 1:*   error: couldn't stop network: QMI protocol error (26):
> 'NoEffect'
> Then, we do see "Network stopped successfully"
>
> Once above Issues appears, when we try start network gets following issue:
>
> *Issue # 2:*
> error: cannot re-start network, PDH already exists
>
> After Issue # 2 appears, when I try to get status, receives following
> message:
>
> *Issue:3*
> error: operation failed: Transaction timed out
> error: couldn't get packet service status
>
> Thanks,
>
>
>
>
>
> On Wed, Aug 12, 2015 at 5:50 PM, Kavula Suresh <kavulas at gmail.com> wrote:
>
>> I am not using Modem Manager, using qmicli and qmi-network manager.
>>
>> Thanks,
>>
>> On Wed, Aug 12, 2015 at 4:58 PM, Markus Gothe <nietzsche at lysator.liu.se>
>> wrote:
>>
>>> Oh, maybe I had to implement that one in uqmi.
>>> Aleksander should know how to use it with ‘mmcli'.
>>>
>>> //M
>>>
>>> On 12 Aug 2015, at 23:13 , Kavula Suresh <kavulas at gmail.com> wrote:
>>>
>>> Mark,
>>>
>>> Can you please give more specific on Auto-Connection. I am using Sierra
>>> MC7354 Modem, is there such kind of profile setting?
>>>
>>> Thanks
>>>
>>> On Wed, Aug 12, 2015 at 4:03 PM, Markus Gothe <nietzsche at lysator.liu.se>
>>> wrote:
>>>
>>>> Try to disable autoconnect.
>>>>
>>>> //M
>>>> On 12 Aug 2015, at 23:01 , Kavula Suresh <kavulas at gmail.com> wrote:
>>>>
>>>> Hello,
>>>>
>>>> As I integrated qmi, most cases my connection with verizon is getting
>>>> disconnecting sometimes.
>>>>
>>>> To reestablish connection, implemented status monitor mechanism and on
>>>> disconnection stopping (to clear) and then restarting.
>>>>
>>>> For status monitoring, stop and start used qmi-network script. But
>>>> receiving following errors.
>>>>
>>>> *On failure of disconnection:*
>>>>
>>>> Getting status with 'qmicli -d /dev/cdc-wdm0
>>>> --wds-get-packet-service-status --client-cid=8 --client-no-release-cid'...
>>>> Status: disconnected
>>>>
>>>> *After stop:*
>>>>
>>>> Stopping network with 'qmicli -d /dev/cdc-wdm0
>>>> --wds-stop-network=1205846256 --client-cid=8'...
>>>> error: couldn't stop network: QMI protocol error (26): 'NoEffect'
>>>> Network stopped successfully
>>>> Clearing state...
>>>>
>>>> *After start:*
>>>> error: cannot re-start network, PDH already exists
>>>> Status:ReStarted, disconnected Connection
>>>>
>>>>
>>>> Can you please give some suggestions on this.
>>>>
>>>> Thanks,
>>>> _______________________________________________
>>>> libqmi-devel mailing list
>>>> libqmi-devel at lists.freedesktop.org
>>>> http://lists.freedesktop.org/mailman/listinfo/libqmi-devel
>>>>
>>>>
>>>> //Markus - The panama-hat hacker
>>>>
>>>>
>>>
>>> //Markus - The panama-hat hacker
>>>
>>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.freedesktop.org/archives/libqmi-devel/attachments/20150923/8c9d0e07/attachment.html>