No SIM Slot Paths

[Bushman, Jeff]

This is what I get:

root at de-01:~# qmicli -d /dev/cdc-wdm0 -p --uim-get-slot-status
[/dev/cdc-wdm0] Successfully got slots status
[/dev/cdc-wdm0] 2 physical slots found:
  Physical slot 1:
     Card status: unknown
     Slot status: active
    Logical slot: 1
  Physical slot 2:
     Card status: unknown
     Slot status: inactive
root at de-01:~# qmicli -d /dev/cdc-wdm0 -p --uim-get-card-status
[/dev/cdc-wdm0] Successfully got card status
Provisioning applications:
	Primary GW:   slot '1', application '1'
	Primary 1X:   session doesn't exist
	Secondary GW: session doesn't exist
	Secondary 1X: session doesn't exist
Slot [1]:
	Card state: 'present'
	UPIN state: 'not-initialized'
		UPIN retries: '0'
		UPUK retries: '0'
	Application [1]:
		Application type:  'usim (2)'
		Application state: 'ready'
		Application ID:
			A0:00:00:00:87:10:02:FF:FF:FF:FF:89:03:02:00:00
		Personalization state: 'ready'
		UPIN replaces PIN1: 'no'
		PIN1 state: 'disabled'
			PIN1 retries: '3'
			PUK1 retries: '10'
		PIN2 state: 'enabled-not-verified'
			PIN2 retries: '3'
			PUK2 retries: '10'
	Application [2]:
		Application type:  'isim (5)'
		Application state: 'detected'
		Application ID:
			A0:00:00:00:87:10:04:FF:FF:FF:FF:89:03:02:00:00
		Personalization state: 'unknown'
		UPIN replaces PIN1: 'no'
		PIN1 state: 'disabled'
			PIN1 retries: '3'
			PUK1 retries: '10'
		PIN2 state: 'not-initialized'
			PIN2 retries: '0'
			PUK2 retries: '0'
Slot [2]:
	Card state: 'absent'
	UPIN state: 'not-initialized'
		UPIN retries: '0'
		UPUK retries: '0'
root at de-01:~# mbimcli -d /dev/cdc-wdm0 -p --ms-query-device-slot-mappings
[/dev/cdc-wdm0] Slot mappings retrieved:
	 Executor '0': slot '0'

So it appears that the data is there in QMI mode, but not MBIM mode?

Jeff

-----Original Message-----
From: Aleksander Morgado <aleksander at aleksander.es> 
Sent: Thursday, November 18, 2021 1:09 AM
To: Eric Caruso <ejcaruso at chromium.org>
Cc: Bushman, Jeff <jbushman at ciena.com>; modemmanager-devel at lists.freedesktop.org
Subject: [**EXTERNAL**] Re: No SIM Slot Paths

Hey,

>
> New enough QMI and MBIM modems have messages to gather all the data for each connected SIM. It's possible that the message is simply not supported by your modem, since 1.18.2 should be new enough such that the MBIM implementation of load_sim_slots, etc. is available.
>

Let's confirm whether the modem supports them or not; Jeff can you run the following commands in the MC7455?

$ qmicli -d /dev/cdc-wdm0 -p --uim-get-slot-status $ qmicli -d /dev/cdc-wdm0 -p --uim-get-card-status $ mbimcli -d /dev/cdc-wdm0 -p --ms-query-device-slot-mappings

--
Aleksander
https://urldefense.com/v3/__https://aleksander.es__;!!OSsGDw!aU0cMFxJaX5umiSfQgu_7vPROh_5eaLghoOP-3YAJRQINkoc78qtuUPHiq5_fA$ [aleksander[.]es]