[Nouveau] GM108GLM?
Karol Herbst
karolherbst at gmail.com
Thu Dec 8 14:32:49 UTC 2016
you can boot with nouveau.config=NvBoost=2 to enable higher clocks,
but that won't fill in the difference compared to Intel. For this
there are some changes needed on the mesa side regarding scheduling.
Also keep in mind, that PCIe is an important bottleneck here, because
the GPU can't push frames fast enough through the bus, that's why any
"high FPS" benchmark will be in favour of intel, because Intel doesn't
need to copy all the frames through the bus.
2016-12-08 14:46 GMT+01:00 Sune Mølgaard <smo at translucent.dk>:
> Aha! That seems to do it.
>
> If I interpret correctly, it doesn't set it quite to full power, though,
> but it's certainly an improvement:
>
> 07: core 405 MHz memory 810 MHz
> 0a: core 270-1124 MHz memory 1600 MHz
> 0f: core 270-1124 MHz memory 2002 MHz AC DC *
> AC: core 1012 MHz memory 2002 MHz
>
> A short run of glmark2 shows aver 100% improvement to ~550 FPS.
>
> Interestingly, it's still nowhere near a match for the built-in
> Broadwell-U with i915, which runs at ~1400 - ~1900 FPS.
>
> Thank you very much - I'll keep a look-out for future improvements :-)
>
> Best regards,
>
> Sune Mølgaard
>
> On 2016-12-08 14:14, Karol Herbst wrote:
>> also you can't change the clocks when there is nothing running on the
>> GPU. I have some patches pending for this in another series, but maybe
>> I may be able toe extract those fixes.
>>
>> Changing the clocks while something is running shouldn't cause any
>> troubles. Alternatively if you don't care about power consumption, you
>> can boot with nouveau.runpm=0 so that the gpu is always on.
>>
>> 2016-12-08 13:25 GMT+01:00 Sune Mølgaard <smo at translucent.dk>:
>>> Hi,
>>>
>>> With drm-next from
>>> http://kernel.ubuntu.com/~kernel-ppa/mainline/drm-next/2016-12-08/
>>>
>>> I don't get the error messages, but I still get a soft cpu lockup.
>>>
>>> What info would you need from me to get it working?
>>>
>>> Best regards,
>>>
>>> Sune Mølgaard
>>>
>>>
>>> On 2016-12-08 08:10, Karol Herbst wrote:
>>>> hi,
>>>>
>>>> give the drm-next kernel tree a try. Sadly the reclocking improvements didn't land with 4.9, so 4.10 is required.
>>>>
>>>> Greetings.
>>>>
>>>> On 7 December 2016 10:26:44 a.m. GMT+01:00, "Sune Mølgaard" <smo at translucent.dk> wrote:
>>>>> Hi again,
>>>>>
>>>>> It works :-)
>>>>>
>>>>> Reclocking, however, is another kettle of fish.
>>>>>
>>>>> Trying #echo 0f > /sys/kernel/debug/dri/0/pstate hangs X.
>>>>>
>>>>> Trying the same with no X running reveals:
>>>>>
>>>>> Dec 7 10:08:42 dell-smo kernel: [ 728.831020] nouveau 0000:08:00.0:
>>>>> clk: unable to find matching pll values
>>>>>
>>>>> a number of time as then soft lockup.
>>>>>
>>>>> Very much akin to
>>>>> https://people.freedesktop.org/~cbrill/dri-log/?channel=nouveau&date=2016-04-14
>>>>> , actually, so what I gather from that is that I need to provide you
>>>>> guys with some info about the card, so which do you need, and how do I
>>>>> extract them?
>>>>>
>>>>> Best regards,
>>>>>
>>>>> Sune Mølgaard
>>>>>
>>>>> On 2016-10-27 11:06, Pierre Moreau wrote:
>>>>>> Hello,
>>>>>>
>>>>>> The idea was to use the modesetting DDX instead of Nouveau’s one for
>>>>> Maxwell+
>>>>>> as EXA was [broken][1]. But you can give a try at Ilia’s
>>>>> [patches][2], which
>>>>>> fix the Nouveau DDX for GM10x and GM20x (I don’t think it has been
>>>>> tested on a
>>>>>> GM108 yet).
>>>>>>
>>>>>> Best regards,
>>>>>> Pierre Moreau
>>>>>>
>>>>>> [1]:
>>>>> https://cgit.freedesktop.org/nouveau/xf86-video-nouveau/commit/?id=3e2e0faa2ee1cce9c1bb5c7ad80d0592460f3edc
>>>>>> [2]: https://github.com/imirkin/xf86-video-nouveau/
>>>>>>
>>>>>>
>>>>>> On 11:29 am - Oct 18 2016, Sune Mølgaard wrote:
>>>>>>> Hi,
>>>>>>>
>>>>>>> It would seem like it (attachments are from 4.9-rc1, btw), but it
>>>>>>> doesn't look like there is any support in the Xorg driver.
>>>>>>>
>>>>>>> How can I help with that?
>>>>>>>
>>>>>>> Best regards,
>>>>>>>
>>>>>>> Sune Mølgaard
>>>>>>> Translucent ApS
>>>>>>>
>>>>>>> On 2016-04-22 09:33, Pierre Moreau wrote:
>>>>>>>> Hello,
>>>>>>>>
>>>>>>>> A patch was merged yesterday to recognise GM108 (see
>>>>>>>>
>>>>> https://github.com/skeggsb/nouveau/commit/3da1f2a19e5e8dc8d68a4400d9cca01c64ecd59e).
>>>>>>>> I guess it will make it into 4.7.
>>>>>>>>
>>>>>>>> Pierre
>>>>>>>
>>>>>>
>>>>>>> lspci -vvvv
>>>>>>> 00:00.0 Host bridge: Intel Corporation Broadwell-U Host Bridge -OPI
>>>>> (rev 09)
>>>>>>> Subsystem: Lenovo Broadwell-U Host Bridge -OPI
>>>>>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx-
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort+ >SERR- <PERR- INTx-
>>>>>>> Latency: 0
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: bdw_uncore
>>>>>>>
>>>>>>> 00:02.0 VGA compatible controller: Intel Corporation Broadwell-U
>>>>> Integrated Graphics (rev 09) (prog-if 00 [VGA controller])
>>>>>>> Subsystem: Lenovo Broadwell-U Integrated Graphics
>>>>>>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx+
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0
>>>>>>> Interrupt: pin A routed to IRQ 49
>>>>>>> Region 0: Memory at f2000000 (64-bit, non-prefetchable) [size=16M]
>>>>>>> Region 2: Memory at c0000000 (64-bit, prefetchable) [size=512M]
>>>>>>> Region 4: I/O ports at 4000 [size=64]
>>>>>>> [virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: i915
>>>>>>> Kernel modules: i915
>>>>>>>
>>>>>>> 00:03.0 Audio device: Intel Corporation Broadwell-U Audio Controller
>>>>> (rev 09)
>>>>>>> Subsystem: Lenovo Broadwell-U Audio Controller
>>>>>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx+
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0, Cache Line Size: 64 bytes
>>>>>>> Interrupt: pin A routed to IRQ 50
>>>>>>> Region 0: Memory at f4230000 (64-bit, non-prefetchable) [size=16K]
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: snd_hda_intel
>>>>>>> Kernel modules: snd_hda_intel
>>>>>>>
>>>>>>> 00:14.0 USB controller: Intel Corporation Wildcat Point-LP USB xHCI
>>>>> Controller (rev 03) (prog-if 30 [XHCI])
>>>>>>> Subsystem: Lenovo Wildcat Point-LP USB xHCI Controller
>>>>>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx+
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0
>>>>>>> Interrupt: pin A routed to IRQ 42
>>>>>>> Region 0: Memory at f4220000 (64-bit, non-prefetchable) [size=64K]
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: xhci_hcd
>>>>>>>
>>>>>>> 00:16.0 Communication controller: Intel Corporation Wildcat Point-LP
>>>>> MEI Controller #1 (rev 03)
>>>>>>> Subsystem: Lenovo Wildcat Point-LP MEI Controller
>>>>>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx+
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0
>>>>>>> Interrupt: pin A routed to IRQ 46
>>>>>>> Region 0: Memory at f4239000 (64-bit, non-prefetchable) [size=32]
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: mei_me
>>>>>>> Kernel modules: mei_me
>>>>>>>
>>>>>>> 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection
>>>>> (3) I218-V (rev 03)
>>>>>>> Subsystem: Lenovo Ethernet Connection (3) I218-V
>>>>>>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx+
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0
>>>>>>> Interrupt: pin A routed to IRQ 43
>>>>>>> Region 0: Memory at f4200000 (32-bit, non-prefetchable) [size=128K]
>>>>>>> Region 1: Memory at f423e000 (32-bit, non-prefetchable) [size=4K]
>>>>>>> Region 2: I/O ports at 4080 [size=32]
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: e1000e
>>>>>>> Kernel modules: e1000e
>>>>>>>
>>>>>>> 00:1b.0 Audio device: Intel Corporation Wildcat Point-LP High
>>>>> Definition Audio Controller (rev 03)
>>>>>>> Subsystem: Lenovo Wildcat Point-LP High Definition Audio Controller
>>>>>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx+
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 32, Cache Line Size: 64 bytes
>>>>>>> Interrupt: pin A routed to IRQ 47
>>>>>>> Region 0: Memory at f4234000 (64-bit, non-prefetchable) [size=16K]
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: snd_hda_intel
>>>>>>> Kernel modules: snd_hda_intel
>>>>>>>
>>>>>>> 00:1c.0 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express
>>>>> Root Port #6 (rev e3) (prog-if 00 [Normal decode])
>>>>>>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx-
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0, Cache Line Size: 64 bytes
>>>>>>> Interrupt: pin B routed to IRQ 17
>>>>>>> Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
>>>>>>> I/O behind bridge: 0000f000-00000fff
>>>>>>> Memory behind bridge: f4100000-f41fffff
>>>>>>> Prefetchable memory behind bridge:
>>>>> 00000000fff00000-00000000000fffff
>>>>>>> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort+ <SERR- <PERR-
>>>>>>> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
>>>>>>> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: pcieport
>>>>>>> Kernel modules: shpchp
>>>>>>>
>>>>>>> 00:1c.1 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express
>>>>> Root Port #3 (rev e3) (prog-if 00 [Normal decode])
>>>>>>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx-
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0, Cache Line Size: 64 bytes
>>>>>>> Interrupt: pin C routed to IRQ 18
>>>>>>> Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
>>>>>>> I/O behind bridge: 0000f000-00000fff
>>>>>>> Memory behind bridge: f4000000-f40fffff
>>>>>>> Prefetchable memory behind bridge:
>>>>> 00000000fff00000-00000000000fffff
>>>>>>> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort+ <SERR- <PERR-
>>>>>>> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
>>>>>>> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: pcieport
>>>>>>> Kernel modules: shpchp
>>>>>>>
>>>>>>> 00:1c.4 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express
>>>>> Root Port #5 (rev e3) (prog-if 00 [Normal decode])
>>>>>>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx-
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0, Cache Line Size: 64 bytes
>>>>>>> Interrupt: pin A routed to IRQ 16
>>>>>>> Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
>>>>>>> I/O behind bridge: 00003000-00003fff
>>>>>>> Memory behind bridge: f3000000-f3ffffff
>>>>>>> Prefetchable memory behind bridge:
>>>>> 00000000e0000000-00000000f1ffffff
>>>>>>> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort+ <SERR- <PERR-
>>>>>>> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
>>>>>>> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: pcieport
>>>>>>> Kernel modules: shpchp
>>>>>>>
>>>>>>> 00:1d.0 USB controller: Intel Corporation Wildcat Point-LP USB EHCI
>>>>> Controller (rev 03) (prog-if 20 [EHCI])
>>>>>>> Subsystem: Lenovo Wildcat Point-LP USB EHCI Controller
>>>>>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx-
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0
>>>>>>> Interrupt: pin A routed to IRQ 23
>>>>>>> Region 0: Memory at f423d000 (32-bit, non-prefetchable) [size=1K]
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: ehci-pci
>>>>>>>
>>>>>>> 00:1f.0 ISA bridge: Intel Corporation Wildcat Point-LP LPC
>>>>> Controller (rev 03)
>>>>>>> Subsystem: Lenovo Wildcat Point-LP LPC Controller
>>>>>>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx-
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: lpc_ich
>>>>>>> Kernel modules: lpc_ich
>>>>>>>
>>>>>>> 00:1f.2 SATA controller: Intel Corporation Wildcat Point-LP SATA
>>>>> Controller [AHCI Mode] (rev 03) (prog-if 01 [AHCI 1.0])
>>>>>>> Subsystem: Lenovo Wildcat Point-LP SATA Controller [AHCI Mode]
>>>>>>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx-
>>>>>>> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0
>>>>>>> Interrupt: pin B routed to IRQ 19
>>>>>>> Region 0: I/O ports at 40a8 [size=8]
>>>>>>> Region 1: I/O ports at 40b4 [size=4]
>>>>>>> Region 2: I/O ports at 40a0 [size=8]
>>>>>>> Region 3: I/O ports at 40b0 [size=4]
>>>>>>> Region 4: I/O ports at 4060 [size=32]
>>>>>>> Region 5: Memory at f423c000 (32-bit, non-prefetchable) [size=2K]
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: ahci
>>>>>>> Kernel modules: ahci
>>>>>>>
>>>>>>> 00:1f.3 SMBus: Intel Corporation Wildcat Point-LP SMBus Controller
>>>>> (rev 03)
>>>>>>> Subsystem: Lenovo Wildcat Point-LP SMBus Controller
>>>>>>> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx-
>>>>>>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Interrupt: pin C routed to IRQ 10
>>>>>>> Region 0: Memory at f4238000 (64-bit, non-prefetchable) [size=256]
>>>>>>> Region 4: I/O ports at efa0 [size=32]
>>>>>>> Kernel modules: i2c_i801
>>>>>>>
>>>>>>> 00:1f.6 Signal processing controller: Intel Corporation Wildcat
>>>>> Point-LP Thermal Management Controller (rev 03)
>>>>>>> Subsystem: Lenovo Wildcat Point-LP Thermal Management Controller
>>>>>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx-
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0
>>>>>>> Interrupt: pin C routed to IRQ 18
>>>>>>> Region 0: Memory at f423b000 (64-bit, non-prefetchable) [size=4K]
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: intel_pch_thermal
>>>>>>> Kernel modules: intel_pch_thermal
>>>>>>>
>>>>>>> 02:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd.
>>>>> RTS5227 PCI Express Card Reader (rev 01)
>>>>>>> Subsystem: Lenovo RTS5227 PCI Express Card Reader
>>>>>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx+
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0, Cache Line Size: 64 bytes
>>>>>>> Interrupt: pin A routed to IRQ 44
>>>>>>> Region 0: Memory at f4100000 (32-bit, non-prefetchable) [size=4K]
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: rtsx_pci
>>>>>>> Kernel modules: rtsx_pci
>>>>>>>
>>>>>>> 03:00.0 Network controller: Intel Corporation Wireless 7265 (rev 99)
>>>>>>> Subsystem: Intel Corporation Dual Band Wireless-AC 7265
>>>>>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx+
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0, Cache Line Size: 64 bytes
>>>>>>> Interrupt: pin A routed to IRQ 48
>>>>>>> Region 0: Memory at f4000000 (64-bit, non-prefetchable) [size=8K]
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: iwlwifi
>>>>>>> Kernel modules: iwlwifi
>>>>>>>
>>>>>>> 08:00.0 3D controller: NVIDIA Corporation GM108GLM [Quadro K620M]
>>>>> (rev a2)
>>>>>>> Subsystem: Lenovo GM108GLM [Quadro K620M]
>>>>>>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>> Stepping- SERR- FastB2B- DisINTx+
>>>>>>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>>>>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>>>>> Latency: 0, Cache Line Size: 64 bytes
>>>>>>> Interrupt: pin A routed to IRQ 45
>>>>>>> Region 0: Memory at f3000000 (32-bit, non-prefetchable) [size=16M]
>>>>>>> Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
>>>>>>> Region 3: Memory at f0000000 (64-bit, prefetchable) [size=32M]
>>>>>>> Region 5: I/O ports at 3000 [size=128]
>>>>>>> Expansion ROM at <ignored> [disabled]
>>>>>>> Capabilities: <access denied>
>>>>>>> Kernel driver in use: nouveau
>>>>>>> Kernel modules: nvidiafb, nouveau
>>>>>>>
>>>>>>
>>>>>>> dmesg |egrep -i "nouveau|nvidia"
>>>>>>> [ 1.893467] nouveau: detected PR support, will not use DSM
>>>>>>> [ 1.893677] nouveau 0000:08:00.0: NVIDIA GM108 (1183a0a2)
>>>>>>> [ 1.907342] nouveau 0000:08:00.0: bios: version 82.08.1f.00.03
>>>>>>> [ 1.991211] nouveau 0000:08:00.0: priv: HUB0: 6013d4 badf573f
>>>>> (1d408200)
>>>>>>> [ 1.991212] nouveau 0000:08:00.0: fb: 2048 MiB DDR3
>>>>>>> [ 3.269352] nouveau 0000:08:00.0: DRM: VRAM: 2048 MiB
>>>>>>> [ 3.269408] nouveau 0000:08:00.0: DRM: GART: 1048576 MiB
>>>>>>> [ 3.269465] nouveau 0000:08:00.0: DRM: Pointer to TMDS table
>>>>> invalid
>>>>>>> [ 3.269523] nouveau 0000:08:00.0: DRM: DCB version 4.0
>>>>>>> [ 3.269579] nouveau 0000:08:00.0: DRM: Pointer to flat panel
>>>>> table invalid
>>>>>>> [ 3.451054] nouveau 0000:08:00.0: DRM: MM: using COPY for buffer
>>>>> copies
>>>>>>> [ 3.451117] [drm] Initialized nouveau 1.3.1 20120801 for
>>>>> 0000:08:00.0 on minor 0
>>>>>>> [ 8.925115] nouveau 0000:08:00.0: DRM: evicting buffers...
>>>>>>> [ 8.925189] nouveau 0000:08:00.0: DRM: waiting for kernel
>>>>> channels to go idle...
>>>>>>> [ 8.925283] nouveau 0000:08:00.0: DRM: suspending client object
>>>>> trees...
>>>>>>> [ 8.929091] nouveau 0000:08:00.0: DRM: suspending kernel object
>>>>> tree...
>>>>>>> [ 17.449259] hid_logitech_hidpp hid_logitech_dj usbhid hid
>>>>> crct10dif_pclmul rtsx_pci_sdmmc crc32_pclmul crc32c_intel mmc_core
>>>>> nouveau ghash_clmulni_intel aesni_intel mxm_wmi i2c_algo_bit aes_x86_64
>>>>> ttm lrw gf128mul glue_helper drm_kms_helper ablk_helper cryptd
>>>>> syscopyarea sysfillrect psmouse sysimgblt fb_sys_fops drm ahci libahci
>>>>> rtsx_pci e1000e ptp pps_core thermal wmi fjes video button
>>>>>>> [ 18.641499] nouveau 0000:08:00.0: DRM: resuming kernel object
>>>>> tree...
>>>>>>> [ 18.724503] nouveau 0000:08:00.0: priv: HUB0: 6013d4 badf573f
>>>>> (1f408200)
>>>>>>> [ 18.761491] nouveau 0000:08:00.0: priv: HUB0: 10ecc0 ffffffff
>>>>> (1d40822c)
>>>>>>> [ 18.761992] nouveau 0000:08:00.0: DRM: resuming client object
>>>>> trees...
>>>>>>> [ 26.025637] nouveau 0000:08:00.0: DRM: evicting buffers...
>>>>>>> [ 26.025639] nouveau 0000:08:00.0: DRM: waiting for kernel
>>>>> channels to go idle...
>>>>>>> [ 26.025662] nouveau 0000:08:00.0: DRM: suspending client object
>>>>> trees...
>>>>>>> [ 26.029451] nouveau 0000:08:00.0: DRM: suspending kernel object
>>>>> tree...
>>>>>>
>>>>>>> [ 20.874]
>>>>>>> X.Org X Server 1.18.4
>>>>>>> Release Date: 2016-07-19
>>>>>>> [ 20.874] X Protocol Version 11, Revision 0
>>>>>>> [ 20.874] Build Operating System: Linux 3.13.0-95-generic x86_64
>>>>> Ubuntu
>>>>>>> [ 20.874] Current Operating System: Linux dell-smo
>>>>> 4.9.0-040900rc1-generic #201610151630 SMP Sat Oct 15 20:33:39 UTC 2016
>>>>> x86_64
>>>>>>> [ 20.874] Kernel command line:
>>>>> BOOT_IMAGE=/vmlinuz-4.9.0-040900rc1-generic
>>>>> root=UUID=a9421b5e-ff3f-4ebd-8f9f-13d24c76ba34 ro
>>>>> cryptopts=target=sda6_crypt,source=/dev/disk/by-uuid/64096e82-f7f4-4917-80df-e123aa15a022,discard
>>>>> vt.handoff=7
>>>>>>> [ 20.874] Build Date: 14 September 2016 03:33:24PM
>>>>>>> [ 20.874] xorg-server 2:1.18.4-0ubuntu0.1 (For technical support
>>>>> please see http://www.ubuntu.com/support)
>>>>>>> [ 20.874] Current version of pixman: 0.33.6
>>>>>>> [ 20.874] Before reporting problems, check http://wiki.x.org
>>>>>>> to make sure that you have the latest version.
>>>>>>> [ 20.874] Markers: (--) probed, (**) from config file, (==)
>>>>> default setting,
>>>>>>> (++) from command line, (!!) notice, (II) informational,
>>>>>>> (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
>>>>>>> [ 20.874] (==) Log file: "/var/log/Xorg.0.log", Time: Tue Oct 18
>>>>> 09:21:13 2016
>>>>>>> [ 20.877] (==) Using system config directory
>>>>> "/usr/share/X11/xorg.conf.d"
>>>>>>> [ 20.881] (==) No Layout section. Using the first Screen
>>>>> section.
>>>>>>> [ 20.881] (==) No screen section available. Using defaults.
>>>>>>> [ 20.881] (**) |-->Screen "Default Screen Section" (0)
>>>>>>> [ 20.881] (**) | |-->Monitor "<default monitor>"
>>>>>>> [ 20.882] (==) No monitor specified for screen "Default Screen
>>>>> Section".
>>>>>>> Using a default monitor configuration.
>>>>>>> [ 20.882] (==) Automatically adding devices
>>>>>>> [ 20.882] (==) Automatically enabling devices
>>>>>>> [ 20.882] (==) Automatically adding GPU devices
>>>>>>> [ 20.882] (==) Max clients allowed: 256, resource mask: 0x1fffff
>>>>>>> [ 20.889] (WW) The directory "/usr/share/fonts/X11/cyrillic" does
>>>>> not exist.
>>>>>>> [ 20.889] Entry deleted from font path.
>>>>>>> [ 20.892] (WW) The directory "/usr/share/fonts/X11/75dpi/" does
>>>>> not exist.
>>>>>>> [ 20.892] Entry deleted from font path.
>>>>>>> [ 20.893] (WW) The directory "/usr/share/fonts/X11/75dpi" does
>>>>> not exist.
>>>>>>> [ 20.893] Entry deleted from font path.
>>>>>>> [ 20.893] (==) FontPath set to:
>>>>>>> /usr/share/fonts/X11/misc,
>>>>>>> /usr/share/fonts/X11/100dpi/:unscaled,
>>>>>>> /usr/share/fonts/X11/Type1,
>>>>>>> /usr/share/fonts/X11/100dpi,
>>>>>>> built-ins
>>>>>>> [ 20.893] (==) ModulePath set to
>>>>> "/usr/lib/x86_64-linux-gnu/xorg/extra-modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
>>>>>>> [ 20.893] (II) The server relies on udev to provide the list of
>>>>> input devices.
>>>>>>> If no devices become available, reconfigure udev or disable
>>>>> AutoAddDevices.
>>>>>>> [ 20.894] (II) Loader magic: 0x563366d65dc0
>>>>>>> [ 20.894] (II) Module ABI versions:
>>>>>>> [ 20.894] X.Org ANSI C Emulation: 0.4
>>>>>>> [ 20.894] X.Org Video Driver: 20.0
>>>>>>> [ 20.894] X.Org XInput driver : 22.1
>>>>>>> [ 20.894] X.Org Server Extension : 9.0
>>>>>>> [ 20.895] (++) using VT number 7
>>>>>>>
>>>>>>> [ 20.895] (II) systemd-logind: logind integration requires
>>>>> -keeptty and -keeptty was not provided, disabling logind integration
>>>>>>> [ 20.895] (II) xfree86: Adding drm device (/dev/dri/card1)
>>>>>>> [ 20.910] (II) xfree86: Adding drm device (/dev/dri/card0)
>>>>>>> [ 20.912] (--) PCI:*(0:0:2:0) 8086:1616:17aa:2225 rev 9, Mem @
>>>>> 0xf2000000/16777216, 0xc0000000/536870912, I/O @ 0x00004000/64, BIOS @
>>>>> 0x????????/131072
>>>>>>> [ 20.912] (--) PCI: (0:8:0:0) 10de:137a:17aa:2225 rev 162, Mem @
>>>>> 0xf3000000/16777216, 0xe0000000/268435456, 0xf0000000/33554432, I/O @
>>>>> 0x00003000/128
>>>>>>> [ 20.912] (II) LoadModule: "glx"
>>>>>>> [ 20.936] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
>>>>>>> [ 20.980] (II) Module glx: vendor="X.Org Foundation"
>>>>>>> [ 20.980] compiled for 1.18.4, module version = 1.0.0
>>>>>>> [ 20.980] ABI class: X.Org Server Extension, version 9.0
>>>>>>> [ 20.980] (==) AIGLX enabled
>>>>>>> [ 20.980] (==) Matched intel as autoconfigured driver 0
>>>>>>> [ 20.980] (==) Matched nvidia as autoconfigured driver 1
>>>>>>> [ 20.980] (==) Matched nouveau as autoconfigured driver 2
>>>>>>> [ 20.980] (==) Matched intel as autoconfigured driver 3
>>>>>>> [ 20.980] (==) Matched modesetting as autoconfigured driver 4
>>>>>>> [ 20.980] (==) Matched fbdev as autoconfigured driver 5
>>>>>>> [ 20.980] (==) Matched vesa as autoconfigured driver 6
>>>>>>> [ 20.980] (==) Assigned the driver to the xf86ConfigLayout
>>>>>>> [ 20.980] (II) LoadModule: "intel"
>>>>>>> [ 20.983] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
>>>>>>> [ 20.988] (II) Module intel: vendor="X.Org Foundation"
>>>>>>> [ 20.988] compiled for 1.18.4, module version = 2.99.917
>>>>>>> [ 20.988] Module class: X.Org Video Driver
>>>>>>> [ 20.988] ABI class: X.Org Video Driver, version 20.0
>>>>>>> [ 20.988] (II) LoadModule: "nvidia"
>>>>>>> [ 20.991] (WW) Warning, couldn't open module nvidia
>>>>>>> [ 20.991] (II) UnloadModule: "nvidia"
>>>>>>> [ 20.991] (II) Unloading nvidia
>>>>>>> [ 20.991] (EE) Failed to load module "nvidia" (module does not
>>>>> exist, 0)
>>>>>>> [ 20.991] (II) LoadModule: "nouveau"
>>>>>>> [ 20.991] (II) Loading
>>>>> /usr/lib/xorg/modules/drivers/nouveau_drv.so
>>>>>>> [ 20.994] (II) Module nouveau: vendor="X.Org Foundation"
>>>>>>> [ 20.994] compiled for 1.18.3, module version = 1.0.13
>>>>>>> [ 20.994] Module class: X.Org Video Driver
>>>>>>> [ 20.994] ABI class: X.Org Video Driver, version 20.0
>>>>>>> [ 20.994] (II) LoadModule: "modesetting"
>>>>>>> [ 20.994] (II) Loading
>>>>> /usr/lib/xorg/modules/drivers/modesetting_drv.so
>>>>>>> [ 20.995] (II) Module modesetting: vendor="X.Org Foundation"
>>>>>>> [ 20.995] compiled for 1.18.4, module version = 1.18.4
>>>>>>> [ 20.995] Module class: X.Org Video Driver
>>>>>>> [ 20.995] ABI class: X.Org Video Driver, version 20.0
>>>>>>> [ 20.995] (II) LoadModule: "fbdev"
>>>>>>> [ 20.995] (WW) Warning, couldn't open module fbdev
>>>>>>> [ 20.995] (II) UnloadModule: "fbdev"
>>>>>>> [ 20.995] (II) Unloading fbdev
>>>>>>> [ 20.995] (EE) Failed to load module "fbdev" (module does not
>>>>> exist, 0)
>>>>>>> [ 20.995] (II) LoadModule: "vesa"
>>>>>>> [ 20.995] (WW) Warning, couldn't open module vesa
>>>>>>> [ 20.995] (II) UnloadModule: "vesa"
>>>>>>> [ 20.995] (II) Unloading vesa
>>>>>>> [ 20.995] (EE) Failed to load module "vesa" (module does not
>>>>> exist, 0)
>>>>>>> [ 20.995] (==) Matched intel as autoconfigured driver 0
>>>>>>> [ 20.995] (==) Matched nvidia as autoconfigured driver 1
>>>>>>> [ 20.995] (==) Matched nouveau as autoconfigured driver 2
>>>>>>> [ 20.995] (==) Matched intel as autoconfigured driver 3
>>>>>>> [ 20.995] (==) Matched modesetting as autoconfigured driver 4
>>>>>>> [ 20.995] (==) Matched fbdev as autoconfigured driver 5
>>>>>>> [ 20.995] (==) Matched vesa as autoconfigured driver 6
>>>>>>> [ 20.995] (==) Assigned the driver to the xf86ConfigLayout
>>>>>>> [ 20.995] (II) LoadModule: "intel"
>>>>>>> [ 20.996] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
>>>>>>> [ 20.996] (II) Module intel: vendor="X.Org Foundation"
>>>>>>> [ 20.996] compiled for 1.18.4, module version = 2.99.917
>>>>>>> [ 20.996] Module class: X.Org Video Driver
>>>>>>> [ 20.996] ABI class: X.Org Video Driver, version 20.0
>>>>>>> [ 20.996] (II) UnloadModule: "intel"
>>>>>>> [ 20.996] (II) Unloading intel
>>>>>>> [ 20.996] (II) Failed to load module "intel" (already loaded,
>>>>> 22067)
>>>>>>> [ 20.996] (II) LoadModule: "nvidia"
>>>>>>> [ 20.996] (WW) Warning, couldn't open module nvidia
>>>>>>> [ 20.996] (II) UnloadModule: "nvidia"
>>>>>>> [ 20.996] (II) Unloading nvidia
>>>>>>> [ 20.996] (EE) Failed to load module "nvidia" (module does not
>>>>> exist, 0)
>>>>>>> [ 20.996] (II) LoadModule: "nouveau"
>>>>>>> [ 20.996] (II) Loading
>>>>> /usr/lib/xorg/modules/drivers/nouveau_drv.so
>>>>>>> [ 20.996] (II) Module nouveau: vendor="X.Org Foundation"
>>>>>>> [ 20.996] compiled for 1.18.3, module version = 1.0.13
>>>>>>> [ 20.996] Module class: X.Org Video Driver
>>>>>>> [ 20.996] ABI class: X.Org Video Driver, version 20.0
>>>>>>> [ 20.996] (II) UnloadModule: "nouveau"
>>>>>>> [ 20.996] (II) Unloading nouveau
>>>>>>> [ 20.996] (II) Failed to load module "nouveau" (already loaded,
>>>>> 0)
>>>>>>> [ 20.996] (II) LoadModule: "modesetting"
>>>>>>> [ 20.996] (II) Loading
>>>>> /usr/lib/xorg/modules/drivers/modesetting_drv.so
>>>>>>> [ 20.996] (II) Module modesetting: vendor="X.Org Foundation"
>>>>>>> [ 20.996] compiled for 1.18.4, module version = 1.18.4
>>>>>>> [ 20.996] Module class: X.Org Video Driver
>>>>>>> [ 20.996] ABI class: X.Org Video Driver, version 20.0
>>>>>>> [ 20.996] (II) UnloadModule: "modesetting"
>>>>>>> [ 20.996] (II) Unloading modesetting
>>>>>>> [ 20.996] (II) Failed to load module "modesetting" (already
>>>>> loaded, 0)
>>>>>>> [ 20.996] (II) LoadModule: "fbdev"
>>>>>>> [ 20.996] (WW) Warning, couldn't open module fbdev
>>>>>>> [ 20.996] (II) UnloadModule: "fbdev"
>>>>>>> [ 20.996] (II) Unloading fbdev
>>>>>>> [ 20.996] (EE) Failed to load module "fbdev" (module does not
>>>>> exist, 0)
>>>>>>> [ 20.996] (II) LoadModule: "vesa"
>>>>>>> [ 20.997] (WW) Warning, couldn't open module vesa
>>>>>>> [ 20.997] (II) UnloadModule: "vesa"
>>>>>>> [ 20.997] (II) Unloading vesa
>>>>>>> [ 20.997] (EE) Failed to load module "vesa" (module does not
>>>>> exist, 0)
>>>>>>> [ 20.997] (II) intel: Driver for Intel(R) Integrated Graphics
>>>>> Chipsets:
>>>>>>> i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
>>>>>>> 915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
>>>>>>> Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35,
>>>>> Q33,
>>>>>>> GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
>>>>>>> [ 20.997] (II) intel: Driver for Intel(R) HD Graphics: 2000-6000
>>>>>>> [ 20.997] (II) intel: Driver for Intel(R) Iris(TM) Graphics:
>>>>> 5100, 6100
>>>>>>> [ 20.997] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics:
>>>>> 5200, 6200, P6300
>>>>>>> [ 20.997] (II) NOUVEAU driver
>>>>>>> [ 20.997] (II) NOUVEAU driver for NVIDIA chipset families :
>>>>>>> [ 20.997] RIVA TNT (NV04)
>>>>>>> [ 20.997] RIVA TNT2 (NV05)
>>>>>>> [ 20.997] GeForce 256 (NV10)
>>>>>>> [ 20.997] GeForce 2 (NV11, NV15)
>>>>>>> [ 20.997] GeForce 4MX (NV17, NV18)
>>>>>>> [ 20.997] GeForce 3 (NV20)
>>>>>>> [ 20.997] GeForce 4Ti (NV25, NV28)
>>>>>>> [ 20.997] GeForce FX (NV3x)
>>>>>>> [ 20.997] GeForce 6 (NV4x)
>>>>>>> [ 20.997] GeForce 7 (G7x)
>>>>>>> [ 20.997] GeForce 8 (G8x)
>>>>>>> [ 20.997] GeForce GTX 200 (NVA0)
>>>>>>> [ 20.997] GeForce GTX 400 (NVC0)
>>>>>>> [ 20.997] (II) modesetting: Driver for Modesetting Kernel
>>>>> Drivers: kms
>>>>>>> [ 21.020] (II) intel(0): Using Kernel Mode Setting driver: i915,
>>>>> version 1.6.0 20160919
>>>>>>> [ 21.020] (II) intel(0): SNA compiled: xserver-xorg-video-intel
>>>>> 2:2.99.917+git1610121931.eb01cc~gd~x (Oibaf <fmrummey at gmail.com>)
>>>>>>> [ 21.020] (II) intel(0): SNA compiled for use with valgrind
>>>>>>> [ 21.022] (II) [drm] nouveau interface version: 1.3.1
>>>>>>> [ 21.022] (EE) Unknown chipset: NV118
>>>>>>> [ 21.022] (WW) Falling back to old probe method for modesetting
>>>>>>> [ 21.024] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD
>>>>> Graphics 5500
>>>>>>> [ 21.024] (--) intel(0): CPU: x86-64, sse2, sse3, ssse3, sse4.1,
>>>>> sse4.2, avx, avx2; using a maximum of 2 threads
>>>>>>> [ 21.024] (II) intel(0): Creating default Display subsection in
>>>>> Screen section
>>>>>>> "Default Screen Section" for depth/fbbpp 24/32
>>>>>>> [ 21.024] (==) intel(0): Depth 24, (--) framebuffer bpp 32
>>>>>>> [ 21.024] (==) intel(0): RGB weight 888
>>>>>>> [ 21.024] (==) intel(0): Default visual is TrueColor
>>>>>>> [ 21.024] (II) intel(0): Output eDP1 has no monitor section
>>>>>>> [ 21.052] (--) intel(0): Found backlight control interface
>>>>> intel_backlight (type 'raw') for output eDP1
>>>>>>> [ 21.052] (II) intel(0): Enabled output eDP1
>>>>>>> [ 21.052] (II) intel(0): Output DP1 has no monitor section
>>>>>>> [ 21.052] (II) intel(0): Enabled output DP1
>>>>>>> [ 21.052] (II) intel(0): Output HDMI1 has no monitor section
>>>>>>> [ 21.052] (II) intel(0): Enabled output HDMI1
>>>>>>> [ 21.052] (II) intel(0): Output DP2 has no monitor section
>>>>>>> [ 21.052] (II) intel(0): Enabled output DP2
>>>>>>> [ 21.052] (II) intel(0): Output HDMI2 has no monitor section
>>>>>>> [ 21.052] (II) intel(0): Enabled output HDMI2
>>>>>>> [ 21.052] (--) intel(0): Using a maximum size of 256x256 for
>>>>> hardware cursors
>>>>>>> [ 21.052] (II) intel(0): Output VIRTUAL1 has no monitor section
>>>>>>> [ 21.052] (II) intel(0): Enabled output VIRTUAL1
>>>>>>> [ 21.052] (--) intel(0): Output eDP1 using initial mode 2880x1620
>>>>> on pipe 0
>>>>>>> [ 21.052] (--) intel(0): Output DP1 using initial mode 2560x1440
>>>>> on pipe 1
>>>>>>> [ 21.052] (==) intel(0): TearFree enabled
>>>>>>> [ 21.052] (==) intel(0): DPI set to (96, 96)
>>>>>>> [ 21.052] (II) Loading sub module "dri2"
>>>>>>> [ 21.052] (II) LoadModule: "dri2"
>>>>>>> [ 21.053] (II) Module "dri2" already built-in
>>>>>>> [ 21.053] (II) Loading sub module "present"
>>>>>>> [ 21.053] (II) LoadModule: "present"
>>>>>>> [ 21.053] (II) Module "present" already built-in
>>>>>>> [ 21.053] (==) Depth 24 pixmap format is 32 bpp
>>>>>>> [ 21.058] (II) intel(0): SNA initialized with Broadwell (gen8)
>>>>> backend
>>>>>>> [ 21.058] (==) intel(0): Backing store enabled
>>>>>>> [ 21.058] (==) intel(0): Silken mouse enabled
>>>>>>> [ 21.060] (II) intel(0): HW Cursor enabled
>>>>>>> [ 21.060] (II) intel(0): RandR 1.2 enabled, ignore the following
>>>>> RandR disabled message.
>>>>>>> [ 21.061] (==) intel(0): DPMS enabled
>>>>>>> [ 21.061] (==) intel(0): Display hotplug detection enabled
>>>>>>> [ 21.061] (II) intel(0): [DRI2] Setup complete
>>>>>>> [ 21.061] (II) intel(0): [DRI2] DRI driver: i965
>>>>>>> [ 21.061] (II) intel(0): [DRI2] VDPAU driver: va_gl
>>>>>>> [ 21.061] (II) intel(0): direct rendering: DRI2 enabled
>>>>>>> [ 21.061] (II) intel(0): hardware support for Present enabled
>>>>>>> [ 21.061] (--) RandR disabled
>>>>>>> [ 21.067] (II) SELinux: Disabled on system
>>>>>>> [ 21.115] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
>>>>>>> [ 21.115] (II) AIGLX: enabled GLX_ARB_create_context
>>>>>>> [ 21.115] (II) AIGLX: enabled GLX_ARB_create_context_profile
>>>>>>> [ 21.115] (II) AIGLX: enabled
>>>>> GLX_EXT_create_context_es{,2}_profile
>>>>>>> [ 21.115] (II) AIGLX: enabled GLX_INTEL_swap_event
>>>>>>> [ 21.115] (II) AIGLX: enabled GLX_SGI_swap_control and
>>>>> GLX_MESA_swap_control
>>>>>>> [ 21.115] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
>>>>>>> [ 21.115] (II) AIGLX: enabled GLX_ARB_fbconfig_float
>>>>>>> [ 21.115] (II) AIGLX: enabled GLX_EXT_fbconfig_packed_float
>>>>>>> [ 21.115] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by
>>>>> buffer objects
>>>>>>> [ 21.115] (II) AIGLX: enabled GLX_ARB_create_context_robustness
>>>>>>> [ 21.116] (II) AIGLX: Loaded and initialized i965
>>>>>>> [ 21.116] (II) GLX: Initialized DRI2 GL provider for screen 0
>>>>>>> [ 21.125] (II) intel(0): switch to mode 2880x1620 at 60.0 on eDP1
>>>>> using pipe 0, position (0, 0), rotation normal, reflection none
>>>>>>> [ 21.126] (II) intel(0): switch to mode 2560x1440 at 60.0 on DP1
>>>>> using pipe 1, position (0, 0), rotation normal, reflection none
>>>>>>> [ 21.127] (II) intel(0): Setting screen physical size to 762 x
>>>>> 428
>>>>>>> [ 21.271] (II) config/udev: Adding input device Power Button
>>>>> (/dev/input/event3)
>>>>>>> [ 21.276] (**) Power Button: Applying InputClass "evdev keyboard
>>>>> catchall"
>>>>>>> [ 21.276] (II) LoadModule: "evdev"
>>>>>>> [ 21.276] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
>>>>>>> [ 21.279] (II) Module evdev: vendor="X.Org Foundation"
>>>>>>> [ 21.280] compiled for 1.18.1, module version = 2.10.1
>>>>>>> [ 21.280] Module class: X.Org XInput Driver
>>>>>>> [ 21.280] ABI class: X.Org XInput driver, version 22.1
>>>>>>> [ 21.280] (II) Using input driver 'evdev' for 'Power Button'
>>>>>>> [ 21.280] (**) Power Button: always reports core events
>>>>>>> [ 21.280] (**) evdev: Power Button: Device: "/dev/input/event3"
>>>>>>> [ 21.280] (--) evdev: Power Button: Vendor 0 Product 0x1
>>>>>>> [ 21.280] (--) evdev: Power Button: Found keys
>>>>>>> [ 21.280] (II) evdev: Power Button: Configuring as keyboard
>>>>>>> [ 21.280] (**) Option "config_info"
>>>>> "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event3"
>>>>>>> [ 21.280] (II) XINPUT: Adding extended input device "Power
>>>>> Button" (type: KEYBOARD, id 6)
>>>>>>> [ 21.280] (**) Option "xkb_rules" "evdev"
>>>>>>> [ 21.280] (**) Option "xkb_model" "pc105"
>>>>>>> [ 21.280] (**) Option "xkb_layout" "dk"
>>>>>>> [ 21.359] (II) config/udev: Adding input device Video Bus
>>>>> (/dev/input/event15)
>>>>>>> [ 21.359] (**) Video Bus: Applying InputClass "evdev keyboard
>>>>> catchall"
>>>>>>> [ 21.359] (II) Using input driver 'evdev' for 'Video Bus'
>>>>>>> [ 21.359] (**) Video Bus: always reports core events
>>>>>>> [ 21.359] (**) evdev: Video Bus: Device: "/dev/input/event15"
>>>>>>> [ 21.359] (--) evdev: Video Bus: Vendor 0 Product 0x6
>>>>>>> [ 21.359] (--) evdev: Video Bus: Found keys
>>>>>>> [ 21.359] (II) evdev: Video Bus: Configuring as keyboard
>>>>>>> [ 21.359] (**) Option "config_info"
>>>>> "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input16/event15"
>>>>>>> [ 21.359] (II) XINPUT: Adding extended input device "Video Bus"
>>>>> (type: KEYBOARD, id 7)
>>>>>>> [ 21.359] (**) Option "xkb_rules" "evdev"
>>>>>>> [ 21.359] (**) Option "xkb_model" "pc105"
>>>>>>> [ 21.359] (**) Option "xkb_layout" "dk"
>>>>>>> [ 21.359] (II) config/udev: Adding input device Video Bus
>>>>> (/dev/input/event16)
>>>>>>> [ 21.359] (**) Video Bus: Applying InputClass "evdev keyboard
>>>>> catchall"
>>>>>>> [ 21.361] (II) Using input driver 'evdev' for 'Video Bus'
>>>>>>> [ 21.361] (**) Video Bus: always reports core events
>>>>>>> [ 21.361] (**) evdev: Video Bus: Device: "/dev/input/event16"
>>>>>>> [ 21.361] (--) evdev: Video Bus: Vendor 0 Product 0x6
>>>>>>> [ 21.361] (--) evdev: Video Bus: Found keys
>>>>>>> [ 21.361] (II) evdev: Video Bus: Configuring as keyboard
>>>>>>> [ 21.361] (**) Option "config_info"
>>>>> "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:09/LNXVIDEO:01/input/input17/event16"
>>>>>>> [ 21.361] (II) XINPUT: Adding extended input device "Video Bus"
>>>>> (type: KEYBOARD, id 8)
>>>>>>> [ 21.361] (**) Option "xkb_rules" "evdev"
>>>>>>> [ 21.361] (**) Option "xkb_model" "pc105"
>>>>>>> [ 21.361] (**) Option "xkb_layout" "dk"
>>>>>>> [ 21.362] (II) config/udev: Adding input device Lid Switch
>>>>> (/dev/input/event1)
>>>>>>> [ 21.362] (II) No input driver specified, ignoring this device.
>>>>>>> [ 21.362] (II) This device may have been added with another
>>>>> device file.
>>>>>>> [ 21.362] (II) config/udev: Adding input device Sleep Button
>>>>> (/dev/input/event2)
>>>>>>> [ 21.362] (**) Sleep Button: Applying InputClass "evdev keyboard
>>>>> catchall"
>>>>>>> [ 21.362] (II) Using input driver 'evdev' for 'Sleep Button'
>>>>>>> [ 21.362] (**) Sleep Button: always reports core events
>>>>>>> [ 21.362] (**) evdev: Sleep Button: Device: "/dev/input/event2"
>>>>>>> [ 21.362] (--) evdev: Sleep Button: Vendor 0 Product 0x3
>>>>>>> [ 21.364] (--) evdev: Sleep Button: Found keys
>>>>>>> [ 21.364] (II) evdev: Sleep Button: Configuring as keyboard
>>>>>>> [ 21.364] (**) Option "config_info"
>>>>> "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3/event2"
>>>>>>> [ 21.364] (II) XINPUT: Adding extended input device "Sleep
>>>>> Button" (type: KEYBOARD, id 9)
>>>>>>> [ 21.364] (**) Option "xkb_rules" "evdev"
>>>>>>> [ 21.364] (**) Option "xkb_model" "pc105"
>>>>>>> [ 21.364] (**) Option "xkb_layout" "dk"
>>>>>>> [ 21.365] (II) config/udev: Adding input device HDA Intel HDMI
>>>>> HDMI/DP,pcm=3 (/dev/input/event18)
>>>>>>> [ 21.365] (II) No input driver specified, ignoring this device.
>>>>>>> [ 21.365] (II) This device may have been added with another
>>>>> device file.
>>>>>>> [ 21.365] (II) config/udev: Adding input device HDA Intel HDMI
>>>>> HDMI/DP,pcm=7 (/dev/input/event19)
>>>>>>> [ 21.365] (II) No input driver specified, ignoring this device.
>>>>>>> [ 21.365] (II) This device may have been added with another
>>>>> device file.
>>>>>>> [ 21.365] (II) config/udev: Adding input device HDA Intel HDMI
>>>>> HDMI/DP,pcm=8 (/dev/input/event20)
>>>>>>> [ 21.365] (II) No input driver specified, ignoring this device.
>>>>>>> [ 21.365] (II) This device may have been added with another
>>>>> device file.
>>>>>>> [ 21.366] (II) config/udev: Adding input device Logitech M705
>>>>> (/dev/input/event4)
>>>>>>> [ 21.366] (**) Logitech M705: Applying InputClass "evdev pointer
>>>>> catchall"
>>>>>>> [ 21.366] (II) Using input driver 'evdev' for 'Logitech M705'
>>>>>>> [ 21.366] (**) Logitech M705: always reports core events
>>>>>>> [ 21.366] (**) evdev: Logitech M705: Device: "/dev/input/event4"
>>>>>>> [ 21.366] (--) evdev: Logitech M705: Vendor 0x46d Product 0x101b
>>>>>>> [ 21.366] (--) evdev: Logitech M705: Found 20 mouse buttons
>>>>>>> [ 21.366] (--) evdev: Logitech M705: Found scroll wheel(s)
>>>>>>> [ 21.366] (--) evdev: Logitech M705: Found relative axes
>>>>>>> [ 21.366] (--) evdev: Logitech M705: Found x and y relative axes
>>>>>>> [ 21.366] (II) evdev: Logitech M705: Configuring as mouse
>>>>>>> [ 21.366] (II) evdev: Logitech M705: Adding scrollwheel support
>>>>>>> [ 21.366] (**) evdev: Logitech M705: YAxisMapping: buttons 4 and
>>>>> 5
>>>>>>> [ 21.366] (**) evdev: Logitech M705: EmulateWheelButton: 4,
>>>>> EmulateWheelInertia: 10, EmulateWheelTimeout: 200
>>>>>>> [ 21.366] (**) Option "config_info"
>>>>> "udev:/sys/devices/pci0000:00/0000:00:14.0/usb2/2-1/2-1:1.2/0003:046D:C52B.0003/0003:046D:101B.0004/input/input6/event4"
>>>>>>> [ 21.366] (II) XINPUT: Adding extended input device "Logitech
>>>>> M705" (type: MOUSE, id 10)
>>>>>>> [ 21.366] (II) evdev: Logitech M705: initialized for relative
>>>>> axes.
>>>>>>> [ 21.366] (**) Logitech M705: (accel) keeping acceleration scheme
>>>>> 1
>>>>>>> [ 21.366] (**) Logitech M705: (accel) acceleration profile 0
>>>>>>> [ 21.366] (**) Logitech M705: (accel) acceleration factor: 2.000
>>>>>>> [ 21.366] (**) Logitech M705: (accel) acceleration threshold: 4
>>>>>>> [ 21.367] (II) config/udev: Adding input device Logitech M705
>>>>> (/dev/input/mouse0)
>>>>>>> [ 21.367] (II) No input driver specified, ignoring this device.
>>>>>>> [ 21.367] (II) This device may have been added with another
>>>>> device file.
>>>>>>> [ 21.367] (II) config/udev: Adding input device Lite-On
>>>>> Technology USB Productivity Option Keyboard( has the hub in # 1 )
>>>>> (/dev/input/event6)
>>>>>>> [ 21.367] (**) Lite-On Technology USB Productivity Option
>>>>> Keyboard( has the hub in # 1 ): Applying InputClass "evdev keyboard
>>>>> catchall"
>>>>>>> [ 21.367] (II) Using input driver 'evdev' for 'Lite-On Technology
>>>>> USB Productivity Option Keyboard( has the hub in # 1 )'
>>>>>>> [ 21.367] (**) Lite-On Technology USB Productivity Option
>>>>> Keyboard( has the hub in # 1 ): always reports core events
>>>>>>> [ 21.367] (**) evdev: Lite-On Technology USB Productivity Option
>>>>> Keyboard( has the hub in # 1 ): Device: "/dev/input/event6"
>>>>>>> [ 21.367] (--) evdev: Lite-On Technology USB Productivity Option
>>>>> Keyboard( has the hub in # 1 ): Vendor 0x4b3 Product 0x301b
>>>>>>> [ 21.367] (--) evdev: Lite-On Technology USB Productivity Option
>>>>> Keyboard( has the hub in # 1 ): Found keys
>>>>>>> [ 21.367] (II) evdev: Lite-On Technology USB Productivity Option
>>>>> Keyboard( has the hub in # 1 ): Configuring as keyboard
>>>>>>> [ 21.367] (**) Option "config_info"
>>>>> "udev:/sys/devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2.2/2-2.2.1/2-2.2.1:1.0/0003:04B3:301B.0005/input/input8/event6"
>>>>>>> [ 21.367] (II) XINPUT: Adding extended input device "Lite-On
>>>>> Technology USB Productivity Option Keyboard( has the hub in # 1 )"
>>>>> (type: KEYBOARD, id 11)
>>>>>>> [ 21.367] (**) Option "xkb_rules" "evdev"
>>>>>>> [ 21.367] (**) Option "xkb_model" "pc105"
>>>>>>> [ 21.367] (**) Option "xkb_layout" "dk"
>>>>>>> [ 21.368] (II) config/udev: Adding input device Lite-On
>>>>> Technology USB Productivity Option Keyboard( has the hub in # 1 )
>>>>> (/dev/input/event7)
>>>>>>> [ 21.368] (**) Lite-On Technology USB Productivity Option
>>>>> Keyboard( has the hub in # 1 ): Applying InputClass "evdev keyboard
>>>>> catchall"
>>>>>>> [ 21.368] (II) Using input driver 'evdev' for 'Lite-On Technology
>>>>> USB Productivity Option Keyboard( has the hub in # 1 )'
>>>>>>> [ 21.368] (**) Lite-On Technology USB Productivity Option
>>>>> Keyboard( has the hub in # 1 ): always reports core events
>>>>>>> [ 21.368] (**) evdev: Lite-On Technology USB Productivity Option
>>>>> Keyboard( has the hub in # 1 ): Device: "/dev/input/event7"
>>>>>>> [ 21.368] (--) evdev: Lite-On Technology USB Productivity Option
>>>>> Keyboard( has the hub in # 1 ): Vendor 0x4b3 Product 0x301b
>>>>>>> [ 21.368] (--) evdev: Lite-On Technology USB Productivity Option
>>>>> Keyboard( has the hub in # 1 ): Found keys
>>>>>>> [ 21.368] (II) evdev: Lite-On Technology USB Productivity Option
>>>>> Keyboard( has the hub in # 1 ): Configuring as keyboard
>>>>>>> [ 21.368] (**) Option "config_info"
>>>>> "udev:/sys/devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2.2/2-2.2.1/2-2.2.1:1.1/0003:04B3:301B.0006/input/input9/event7"
>>>>>>> [ 21.368] (II) XINPUT: Adding extended input device "Lite-On
>>>>> Technology USB Productivity Option Keyboard( has the hub in # 1 )"
>>>>> (type: KEYBOARD, id 12)
>>>>>>> [ 21.368] (**) Option "xkb_rules" "evdev"
>>>>>>> [ 21.368] (**) Option "xkb_model" "pc105"
>>>>>>> [ 21.368] (**) Option "xkb_layout" "dk"
>>>>>>> [ 21.369] (II) config/udev: Adding input device Integrated Camera
>>>>> (/dev/input/event17)
>>>>>>> [ 21.369] (**) Integrated Camera: Applying InputClass "evdev
>>>>> keyboard catchall"
>>>>>>> [ 21.369] (II) Using input driver 'evdev' for 'Integrated Camera'
>>>>>>> [ 21.369] (**) Integrated Camera: always reports core events
>>>>>>> [ 21.369] (**) evdev: Integrated Camera: Device:
>>>>> "/dev/input/event17"
>>>>>>> [ 21.369] (--) evdev: Integrated Camera: Vendor 0x5986 Product
>>>>> 0x366
>>>>>>> [ 21.369] (--) evdev: Integrated Camera: Found keys
>>>>>>> [ 21.369] (II) evdev: Integrated Camera: Configuring as keyboard
>>>>>>> [ 21.369] (**) Option "config_info"
>>>>> "udev:/sys/devices/pci0000:00/0000:00:14.0/usb2/2-8/2-8:1.0/input/input18/event17"
>>>>>>> [ 21.369] (II) XINPUT: Adding extended input device "Integrated
>>>>> Camera" (type: KEYBOARD, id 13)
>>>>>>> [ 21.369] (**) Option "xkb_rules" "evdev"
>>>>>>> [ 21.369] (**) Option "xkb_model" "pc105"
>>>>>>> [ 21.369] (**) Option "xkb_layout" "dk"
>>>>>>> [ 21.370] (II) config/udev: Adding input device HDA Digital
>>>>> PCBeep (/dev/input/event10)
>>>>>>> [ 21.370] (II) No input driver specified, ignoring this device.
>>>>>>> [ 21.370] (II) This device may have been added with another
>>>>> device file.
>>>>>>> [ 21.370] (II) config/udev: Adding input device HDA Intel PCH
>>>>> Dock Mic (/dev/input/event11)
>>>>>>> [ 21.370] (II) No input driver specified, ignoring this device.
>>>>>>> [ 21.370] (II) This device may have been added with another
>>>>> device file.
>>>>>>> [ 21.370] (II) config/udev: Adding input device HDA Intel PCH Mic
>>>>> (/dev/input/event12)
>>>>>>> [ 21.370] (II) No input driver specified, ignoring this device.
>>>>>>> [ 21.370] (II) This device may have been added with another
>>>>> device file.
>>>>>>> [ 21.370] (II) config/udev: Adding input device HDA Intel PCH
>>>>> Dock Headphone (/dev/input/event13)
>>>>>>> [ 21.370] (II) No input driver specified, ignoring this device.
>>>>>>> [ 21.370] (II) This device may have been added with another
>>>>> device file.
>>>>>>> [ 21.375] (II) config/udev: Adding input device HDA Intel PCH
>>>>> Headphone (/dev/input/event14)
>>>>>>> [ 21.375] (II) No input driver specified, ignoring this device.
>>>>>>> [ 21.375] (II) This device may have been added with another
>>>>> device file.
>>>>>>> [ 21.375] (II) config/udev: Adding input device AT Translated Set
>>>>> 2 keyboard (/dev/input/event0)
>>>>>>> [ 21.375] (**) AT Translated Set 2 keyboard: Applying InputClass
>>>>> "evdev keyboard catchall"
>>>>>>> [ 21.375] (II) Using input driver 'evdev' for 'AT Translated Set
>>>>> 2 keyboard'
>>>>>>> [ 21.375] (**) AT Translated Set 2 keyboard: always reports core
>>>>> events
>>>>>>> [ 21.375] (**) evdev: AT Translated Set 2 keyboard: Device:
>>>>> "/dev/input/event0"
>>>>>>> [ 21.375] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1
>>>>> Product 0x1
>>>>>>> [ 21.375] (--) evdev: AT Translated Set 2 keyboard: Found keys
>>>>>>> [ 21.375] (II) evdev: AT Translated Set 2 keyboard: Configuring
>>>>> as keyboard
>>>>>>> [ 21.375] (**) Option "config_info"
>>>>> "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
>>>>>>> [ 21.375] (II) XINPUT: Adding extended input device "AT
>>>>> Translated Set 2 keyboard" (type: KEYBOARD, id 14)
>>>>>>> [ 21.375] (**) Option "xkb_rules" "evdev"
>>>>>>> [ 21.375] (**) Option "xkb_model" "pc105"
>>>>>>> [ 21.375] (**) Option "xkb_layout" "dk"
>>>>>>> [ 21.376] (II) config/udev: Adding input device SynPS/2 Synaptics
>>>>> TouchPad (/dev/input/event5)
>>>>>>> [ 21.376] (**) SynPS/2 Synaptics TouchPad: Applying InputClass
>>>>> "evdev touchpad catchall"
>>>>>>> [ 21.376] (**) SynPS/2 Synaptics TouchPad: Applying InputClass
>>>>> "evdev touchscreen catchall"
>>>>>>> [ 21.376] (**) SynPS/2 Synaptics TouchPad: Applying InputClass
>>>>> "touchpad catchall"
>>>>>>> [ 21.376] (**) SynPS/2 Synaptics TouchPad: Applying InputClass
>>>>> "Default clickpad buttons"
>>>>>>> [ 21.376] (II) LoadModule: "synaptics"
>>>>>>> [ 21.376] (II) Loading
>>>>> /usr/lib/xorg/modules/input/synaptics_drv.so
>>>>>>> [ 21.381] (II) Module synaptics: vendor="X.Org Foundation"
>>>>>>> [ 21.381] compiled for 1.18.1, module version = 1.8.2
>>>>>>> [ 21.381] Module class: X.Org XInput Driver
>>>>>>> [ 21.381] ABI class: X.Org XInput driver, version 22.1
>>>>>>> [ 21.381] (II) Using input driver 'synaptics' for 'SynPS/2
>>>>> Synaptics TouchPad'
>>>>>>> [ 21.381] (**) SynPS/2 Synaptics TouchPad: always reports core
>>>>> events
>>>>>>> [ 21.381] (**) Option "Device" "/dev/input/event5"
>>>>>>> [ 21.464] (II) synaptics: SynPS/2 Synaptics TouchPad: found
>>>>> clickpad property
>>>>>>> [ 21.464] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis
>>>>> range 1266 - 5676 (res 45)
>>>>>>> [ 21.464] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis
>>>>> range 1096 - 4758 (res 68)
>>>>>>> [ 21.464] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure
>>>>> range 0 - 255
>>>>>>> [ 21.464] (--) synaptics: SynPS/2 Synaptics TouchPad: finger
>>>>> width range 0 - 15
>>>>>>> [ 21.464] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons:
>>>>> left double triple
>>>>>>> [ 21.464] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2
>>>>> Product 0x7
>>>>>>> [ 21.464] (**) Option "SoftButtonAreas" "50% 0 82% 0 0 0 0 0"
>>>>>>> [ 21.464] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad
>>>>> found
>>>>>>> [ 21.464] (**) SynPS/2 Synaptics TouchPad: always reports core
>>>>> events
>>>>>>> [ 21.500] (**) Option "config_info"
>>>>> "udev:/sys/devices/platform/i8042/serio1/input/input5/event5"
>>>>>>> [ 21.500] (II) XINPUT: Adding extended input device "SynPS/2
>>>>> Synaptics TouchPad" (type: TOUCHPAD, id 15)
>>>>>>> [ 21.500] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel)
>>>>> MinSpeed is now constant deceleration 2.5
>>>>>>> [ 21.500] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel)
>>>>> MaxSpeed is now 1.75
>>>>>>> [ 21.500] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel)
>>>>> AccelFactor is now 0.035
>>>>>>> [ 21.500] (**) SynPS/2 Synaptics TouchPad: (accel) keeping
>>>>> acceleration scheme 1
>>>>>>> [ 21.500] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration
>>>>> profile 1
>>>>>>> [ 21.500] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration
>>>>> factor: 2.000
>>>>>>> [ 21.500] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration
>>>>> threshold: 4
>>>>>>> [ 21.500] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad
>>>>> found
>>>>>>> [ 21.500] (II) config/udev: Adding input device SynPS/2 Synaptics
>>>>> TouchPad (/dev/input/mouse1)
>>>>>>> [ 21.500] (**) SynPS/2 Synaptics TouchPad: Ignoring device from
>>>>> InputClass "touchpad ignore duplicates"
>>>>>>> [ 21.501] (II) config/udev: Adding input device TPPS/2 IBM
>>>>> TrackPoint (/dev/input/event8)
>>>>>>> [ 21.501] (**) TPPS/2 IBM TrackPoint: Applying InputClass "evdev
>>>>> pointer catchall"
>>>>>>> [ 21.501] (**) TPPS/2 IBM TrackPoint: Applying InputClass
>>>>> "trackpoint catchall"
>>>>>>> [ 21.501] (II) Using input driver 'evdev' for 'TPPS/2 IBM
>>>>> TrackPoint'
>>>>>>> [ 21.501] (**) TPPS/2 IBM TrackPoint: always reports core events
>>>>>>> [ 21.501] (**) evdev: TPPS/2 IBM TrackPoint: Device:
>>>>> "/dev/input/event8"
>>>>>>> [ 21.501] (--) evdev: TPPS/2 IBM TrackPoint: Vendor 0x2 Product
>>>>> 0xa
>>>>>>> [ 21.501] (--) evdev: TPPS/2 IBM TrackPoint: Found 3 mouse
>>>>> buttons
>>>>>>> [ 21.501] (--) evdev: TPPS/2 IBM TrackPoint: Found relative axes
>>>>>>> [ 21.501] (--) evdev: TPPS/2 IBM TrackPoint: Found x and y
>>>>> relative axes
>>>>>>> [ 21.501] (II) evdev: TPPS/2 IBM TrackPoint: Configuring as mouse
>>>>>>> [ 21.501] (**) Option "Emulate3Buttons" "true"
>>>>>>> [ 21.501] (**) Option "EmulateWheel" "true"
>>>>>>> [ 21.501] (**) Option "EmulateWheelButton" "2"
>>>>>>> [ 21.501] (**) Option "YAxisMapping" "4 5"
>>>>>>> [ 21.501] (**) evdev: TPPS/2 IBM TrackPoint: YAxisMapping:
>>>>> buttons 4 and 5
>>>>>>> [ 21.501] (**) Option "XAxisMapping" "6 7"
>>>>>>> [ 21.501] (**) evdev: TPPS/2 IBM TrackPoint: XAxisMapping:
>>>>> buttons 6 and 7
>>>>>>> [ 21.501] (**) evdev: TPPS/2 IBM TrackPoint: EmulateWheelButton:
>>>>> 2, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
>>>>>>> [ 21.501] (**) Option "config_info"
>>>>> "udev:/sys/devices/platform/i8042/serio1/serio2/input/input7/event8"
>>>>>>> [ 21.501] (II) XINPUT: Adding extended input device "TPPS/2 IBM
>>>>> TrackPoint" (type: MOUSE, id 16)
>>>>>>> [ 21.501] (II) evdev: TPPS/2 IBM TrackPoint: initialized for
>>>>> relative axes.
>>>>>>> [ 21.501] (**) TPPS/2 IBM TrackPoint: (accel) keeping
>>>>> acceleration scheme 1
>>>>>>> [ 21.501] (**) TPPS/2 IBM TrackPoint: (accel) acceleration
>>>>> profile 0
>>>>>>> [ 21.501] (**) TPPS/2 IBM TrackPoint: (accel) acceleration
>>>>> factor: 2.000
>>>>>>> [ 21.501] (**) TPPS/2 IBM TrackPoint: (accel) acceleration
>>>>> threshold: 4
>>>>>>> [ 21.501] (II) config/udev: Adding input device TPPS/2 IBM
>>>>> TrackPoint (/dev/input/mouse2)
>>>>>>> [ 21.501] (II) No input driver specified, ignoring this device.
>>>>>>> [ 21.501] (II) This device may have been added with another
>>>>> device file.
>>>>>>> [ 21.502] (II) config/udev: Adding input device ThinkPad Extra
>>>>> Buttons (/dev/input/event9)
>>>>>>> [ 21.502] (**) ThinkPad Extra Buttons: Applying InputClass "evdev
>>>>> keyboard catchall"
>>>>>>> [ 21.502] (II) Using input driver 'evdev' for 'ThinkPad Extra
>>>>> Buttons'
>>>>>>> [ 21.502] (**) ThinkPad Extra Buttons: always reports core events
>>>>>>> [ 21.502] (**) evdev: ThinkPad Extra Buttons: Device:
>>>>> "/dev/input/event9"
>>>>>>> [ 21.502] (--) evdev: ThinkPad Extra Buttons: Vendor 0x17aa
>>>>> Product 0x5054
>>>>>>> [ 21.502] (--) evdev: ThinkPad Extra Buttons: Found keys
>>>>>>> [ 21.502] (II) evdev: ThinkPad Extra Buttons: Configuring as
>>>>> keyboard
>>>>>>> [ 21.502] (**) Option "config_info"
>>>>> "udev:/sys/devices/platform/thinkpad_acpi/input/input10/event9"
>>>>>>> [ 21.502] (II) XINPUT: Adding extended input device "ThinkPad
>>>>> Extra Buttons" (type: KEYBOARD, id 17)
>>>>>>> [ 21.502] (**) Option "xkb_rules" "evdev"
>>>>>>> [ 21.502] (**) Option "xkb_model" "pc105"
>>>>>>> [ 21.502] (**) Option "xkb_layout" "dk"
>>>>>>> [ 23.053] (II) intel(0): EDID vendor "MEI", prod id 38562
>>>>>>> [ 23.053] (II) intel(0): EDID quirk: Use maximum size instead
>>>>> of detailed timing sizes.
>>>>>>> [ 23.053] (II) intel(0): Using EDID range info for horizontal
>>>>> sync
>>>>>>> [ 23.053] (II) intel(0): Using EDID range info for vertical
>>>>> refresh
>>>>>>> [ 23.053] (II) intel(0): Printing DDC gathered Modelines:
>>>>>>> [ 23.053] (II) intel(0): Modeline "2880x1620"x0.0 302.50 2880
>>>>> 2924 2928 3076 1620 1629 1630 1640 +hsync +vsync (98.3 kHz eP)
>>>>>>> [ 23.053] (II) intel(0): Modeline "2880x1620"x0.0 302.50 2880
>>>>> 2924 2928 3076 1620 1629 1630 1967 +hsync +vsync (98.3 kHz e)
>>>>>>> [ 23.909] (II) intel(0): resizing framebuffer to 5440x1620
>>>>>>> [ 23.960] (II) intel(0): switch to mode 2560x1440 at 60.0 on DP1
>>>>> using pipe 1, position (2880, 0), rotation normal, reflection none
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>> _______________________________________________
>>>>>>> Nouveau mailing list
>>>>>>> Nouveau at lists.freedesktop.org
>>>>>>> https://lists.freedesktop.org/mailman/listinfo/nouveau
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> ------------------------------------------------------------------------
>>>>>
>>>>> _______________________________________________
>>>>> Nouveau mailing list
>>>>> Nouveau at lists.freedesktop.org
>>>>> https://lists.freedesktop.org/mailman/listinfo/nouveau
>>>>
>>>
>
More information about the Nouveau
mailing list