[Openchrome-users] cn700&Gentoo

[Juergen Hoelker]

Ivor Hewitt wrote:
> On Sunday 07 May 2006 02:16, Juergen Hoelker wrote:
>> (II) LoadModule: "via"
>> (WW) Warning, couldn't open module via
>>
> X can't find your driver. Your distro/ebuild is putting the built module
> somewhere other than where the X build put the rest of the modules.
> Find the location and a ModulePath setting into your xorg pointing to
it... or
> change the location the driver builds to be the same as the others.
>
thx for the tip, that worked so far, but now i can't get any output to
mv TV(PAL), it says in the Xorg.0.log, that no Mode could be loaded:

(--) VIA(0): Detected VIA Technologies VT1625 TV Encoder
(II) VIA(0): ViaTVInit
(II) VIA(0): ViaVT162xInit
(II) VIA(0): VT162xSave
(II) VIA(0): ViaOutputsSelect
(II) VIA(0): ViaOutputsSelect: X Configuration: 0x04
(II) VIA(0): ViaOutputsSelect: BIOS Initialised register: 0x07
(II) VIA(0): ViaOutputsSelect: TV.
(II) VIA(0): ViaModesAttach
(II) VIA(0): TV: Using hsync range of 24.00-80.00 kHz
(II) VIA(0): TV: Using vrefresh range of 50.00-75.00 Hz
(II) VIA(0): Clock range:  20.00 to 230.00 MHz
(II) VIA(0): ViaValidMode: Validating 640x350 (31500)
(II) VIA(0): ViaModePrimaryVGAValid
(II) VIA(0): VT1625ModeValid
(II) VIA(0): Not a mode defined by the TV Encoder.
(II) VIA(0): Mode "640x350" not supported by TV encoder.
(II) VIA(0): Not using default mode "640x350" (unknown reason)
(II) VIA(0): Not using default mode "320x175" (bad mode
clock/interlace/doublescan)
(II) VIA(0): ViaValidMode: Validating 640x400 (31500)
(II) VIA(0): ViaModePrimaryVGAValid
(II) VIA(0): VT1625ModeValid

... (much more here)

(II) VIA(0): TV standard is PAL. This is an incompatible mode.
(II) VIA(0): Mode "720x480Under" not supported by TV encoder.
(II) VIA(0): Not using default mode "720x480Under" (unknown reason)
(II) VIA(0): ViaValidMode: Validating 720x480Fit (28980)
(II) VIA(0): ViaModePrimaryVGAValid
(II) VIA(0): VT1625ModeValid
(II) VIA(0): TV standard is PAL. This is an incompatible mode.
(II) VIA(0): Mode "720x480Fit" not supported by TV encoder.
(II) VIA(0): Not using default mode "720x480Fit" (unknown reason)
(II) VIA(0): ViaValidMode: Validating 720x480Over (27025)
(II) VIA(0): ViaModePrimaryVGAValid
(II) VIA(0): VT1625ModeValid
(II) VIA(0): TV standard is PAL. This is an incompatible mode.
(II) VIA(0): Mode "720x480Over" not supported by TV encoder.
(II) VIA(0): Not using default mode "720x480Over" (unknown reason)
(WW) VIA(0): Mode pool is empty
(EE) VIA(0): No valid modes found
(II) VIA(0): VIAFreeRec
(II) VIA(0): I2C device "I2C bus 2:VT1625" removed.
(II) VIA(0): VIAUnmapMem
(II) VIA(0): VIAFreeScreen
(II) VIA(0): VIAFreeRec
(II) UnloadModule: "via"
(II) UnloadModule: "ddc"
(II) Unloading /usr/lib/xorg/modules/libddc.so
(II) UnloadModule: "i2c"
(II) Unloading /usr/lib/xorg/modules/libi2c.so
(II) UnloadModule: "vgahw"
(II) Unloading /usr/lib/xorg/modules/libvgahw.so
(EE) Screen(s) found, but none have a usable configuration.

and my Modes are:

    Subsection "Display"
        Depth       24
        Modes         "720x576Over" "572x480" "720x480Noscale"
        ViewPort    0 0
    EndSubsection


so, whats wrong here now????